How to make Automatic Irrigation System Using Arduino
HTML-код
- Опубликовано: 16 апр 2019
- PCB for 2$ (any colour) : www.jlcpcb.com
I will show you how to build and implement an automatic irrigation system which can sense the water content in the soil and automatically irrigate your garden. This system can be programmed for different crop requirements and seasonal variations. This system is best suited for drip irrigation technique. I have also tested the system for different soil conditions and water availability.
This System will help you to irrigate your backyard Garden or your Indoor Garden automatically and you need not to worry about watering your favorite plants in your busy schedule.
Arduino UNO is the brain of this system and all the sensors and display devices are controlled by it. A Moisture sensor is used to read the Moisture content of the soil. An LCD is provided to monitor the Soil Status, Ambient Temperature, and Status of Water supply(Water Pump).
Please follow the following Instructable link for circuit diagram and Arduino code.
www.instructables.com/id/How-...
The above instructable is in gardening contest. PLEASE VOTE ME and it is highly appreciated! Thanks
Thank you for watching.
Subscribe for more project Videos. 
Наука
Keep it bro uh helping many of people's out there❤️🔥
Thanks for this project. I think I will give it a go.
Good Sandesh 👍🏻
Sickkk project bruv!!!🦾
Good job man, Where did you get your water level sensor ? (from any online shop maybe ?) I'm looking for the one with reasonable price.
Hey! Thank you very much for this helpful video :D
Great job
nice job! you should maybe make it so it pumps water for like 20 seconds and then waits a minute to read the sensor again since it might take a while until the water reaches the sensor
hi, thank you very much for your video, but do you mind if add pump runtime for 20 sec only then wait for 3 minutes to let the soil soak properly and run it again for 20sec until the sensor will be satisfied. thank you very much in advance
Excellet bro.I have some doubts.1.Whats the use of speaker?2.If I have to use more than one soil moisture senser how can I connect them?
Please make a video on wiring on Perfborad of this project
Hello, I was hoping that you could help me. I like your design, but I want to use a timer and have the moisture sensor as a safety. Also Like to add Co2 read out. Thanks in advance for any help. Skip
Nice👍
Congratulations...
2k subscribers..
Thank you:)
Hi good vedio bro..but one question..bout code ..from where should it downloaded and what should be required
@The Technocrat I uploaded the same code but when my water level switch was OFF then my pump wasn't OFF it was running but the value of PUMP given by LCD was PUMP OFF
Hello sir, can it be implemented in real garden. If yes den what should be the motor capacity.
hi, good project! can you share a link to the float switch sales? thanks
I have a dout about the circut diagram . Can you upload a video on circuit diagram of this automated water irrigation?
PlZ make a video of solar irrigation system with perfect connection
Can you let me what if we went out for few days
Will it work autometically
Hi Sandesh!
hi! is there any way to make this done with a solar power source
sir please can you explain the significance if LM393 in the system above
Can you please give complete details about this project
Where do I get the complete report on this project?
Relay modul kesa lena h mix ya single
while compiling the arduino code i get errors saying undefined reference to `Print::write(unsigned char const*, unsigned int)'
and undefined reference to main ...what can i do ????? please help me i have project demo tmrw
Sir did u upload the code with fixed bugs
Can we use this without the display
Hye can i use this for 2 horsepower water pump?
There is no code for ardunio bro In the link. There is only hardware details
And you have shown how to do wiring on bread board and on the garden you have used it on Perfborad. Tell me which way we have to use to make this project?
I suggest you to construct the project on the prefboard or PCB. But for testing you may try it on breadboard
Thanks The Technocrat
Nice work bro. Please could you help me with the code for the project? It isn't clearly stated on your page. Thanks a lot.
Please bro, could you assist me with the code. It isn't clearly stated on your page and I want to use it for my project? 🙏
Did u got
Are you using two relays?
One for arduino and other for water pump ?
i have use dthe relay only for pump control.
sir is there any code for motor pumpin
Why the water pump always on?
I want a model of this shall u do i give money
Bro agar water level htana ho to code kese set karain????
Sir which water pump did you use please reply sir
it is the small pump used for small fountains and air cooler
Hello technocrat can u make a video of watering using our mob phone when v r not at home , if v make a phone call the system vil do watering
where is the link
cost ?
i have some doubts
Sir I have an issue in the project
My pump doesn't turn off after placing sensor in water 🥺🥺🥺 I have done all other work
Where did you fixed the temperature Sensor?
donde declaro la libreia!! donde!
Where is the link for pcb board zip file
Is this a good project for mechanical engineering
Maybe :) depends on application
Brother where temperature sensor will be connected?? I need it please hep
To the analog input of Arduino. Here in my demo I have it on the PCB itself.. place the sensor where you want to take the temp measurement.
can i have a complete coding?
What is the use of speaker in this project?
Speaker is for notification sound. A piezo buzzer should work fine.
sir the lcd is going weird when the relay switches and pump is on what to do(i used a dc pump)
and when the pump is removed every thing works fine
Have you connected flyback diode to the relay?? Also proper grounding should solve your problem.
No it is 220 V 30W pump.
Looks like a EMI Problem. Try to isolate the microcontroller-lcd circuit in a grounded metal container. Or place the motor , relay and motor wiring circuit away (maybe 2meter) from the circuit. I am not a EMI expert but this is worth a try. Please share your learnings here.
Thanks
Where did you use temperature sensor? i haven't seen in whole video
It is in the PCB itself.
@@TheTechnocrat yes that's why i asked for the temperature sensor it is in the PCB but the function is not explained in their if you show that in video than it would be more helpful and i can understand better
Can i use aurdino nano in place of uno
Yes
How to program different types of codes to aurdino ?
could you be more specific? What are the different types of code? are you referring to number of sensors?
Sir the code in the description is not clearly visible from the pictures given please could you reupload the whole code i needed it for my project
pls email me nsgsarge@gmail.com
will it work without that blue cable which is connected to upload the code
Yes. It is required only to upload the code.
@@TheTechnocrat tq for replying its means a lot, but my 16x2 lcd is not working, i followed ur circuit as in instructables, the lcd is turning on its showing rectangular white dots.
@@HikaruKouki please recheck the circuit and make sure everything is grounded.
White box means there might be problem with pot connected to lcd. Adjust the pot and I think that problem will be solved.
Wont the circuit without lcd
Code link nai mil raha h please link send kr dijiye
Can we use arduino nano for this ?
Yes
Sir will you provide the tool kit for us?
What tool kit. ? Are you taking about the project component?
hello may i know if i use mini water pump where should i connect it with?
Connect it to relay only. But insted of 230V connect to 12 v supply or voltage of mini pump.
@@TheTechnocrat The mini water pump has 2 wires. The red one i should connect to the relay and the black one i should place it at the 5V from the arduino? or should i connect the black wires to 9V battery?
Please send your circuit diagram through Google drive. Or send me a link.
@@TheTechnocrat I build my circuit exactly the same as yours and for the code i downloaded your code too however when i upload it, the result isn't like your demonstration. The lcd display dry soil and pump is on but the water pump is not turn on and when the water level is low the pump says its OFF but the water pump is running. Also the led should light up the same as the relay led turn on. But when the green led from relay is turn on my LED is off. Also the moisture sensor does not react and display soggy soil when i place it into the wet soil. Can you please explain...I had no idea how this can happen because i follow everything like you did. But my project is not working.
Bro I am not able to code it please help me 🥺
What’s the specification of the water pump?
It is a fountain water pump you can buy online or any home supplies store.
@@TheTechnocrat sir i need a complete ready project of this irrigation system can i know the cost for this Project and ur contract details. We selected this project to conduct a final year project in engineering
sir is there any code for motor pumping please tell me sir except motor i completed all of my project
Sorry I didn't understand what is motor pumping code. Can you please elaborate the application. Thanks
@@TheTechnocrat sir i done all the project .but i have doubt is there any code to run the motor?????
i mean you uploaded a code for the project that code is sufficient to run the motor or else is there any code for motor running
The same code can run the motor . Before connecting to the mains supply make sure the relay is working according to logic.
Thanks
Did you finish the project??
sir ,, can we connect it with android application ? if can we did it, then how ???
Yes it is possible. I would suggest you to learn about ESP8266, Bluetooth modules and MIT APP INVENTOR for mobile application. Ofcourse there are many apps in Android store for communication with WiFi and bluetooth modules.
Water level sensor or water pump ka connection kese hua
Plz reply
Bro can we do this without Arduino
if u know pls help me bro i have to submit the mini project. 🤦♂️
but why? Arduino is damn cheap.
no you cannot in your case. cuz you need a lot of electrical knowledge to do with out arduino. Recommend buying the arduino uno.
Hai do you know how to do this project without Arduino ?
@@hazirah5200 yeah we done this
@@WTFWasThat yeah! But it's a task for us
Hello bro can you give the code of this project plz it's urgent
Link in Description. Thank you
please send the arduino code for above project code is not clear in pdf
It is in my instructables page. Find the link in video description.
Code is not clear sir.
Sir can you please tell me about detail in requirements please sir its very urgent to me
All the materials is in the link in Description
@@TheTechnocrat hi sir sorry for late reply I have completed the experiment but I don't know how to work the water pump.the remaining process was completed.can you please tell me about water pump working
Link for code please
I have updated the link for code. Please check the description.
i made this one bt when moist nd soggy soil is detected water stop for a while nd pump is in off mode...after a while pump started automatically...why is it
It is because the sensor detected the soil to be dry after some time and the sudden flood of water might have caused the sensor to detect the moist condition and turn off the pump.
This is the bug I was talking in the video. This can be improved by placing the sensor in the most appropriate place and maybe add a timer in the code to avoid the false trigger of the pump relay.
Seems incomplete
Can I know the cost to purchase the total finished project
9000
@@lakshmiayyam6610 contact details plz
Jlcpcb file give plz
Fucking hell...the code shows error at multiple ends
I'll work for you for free if you'd help me build the devices I have in my head.
We can do emps and RVs to fly to the Moon even.
I just don't have the mechanical and engineering skills you have.
Nice :o