*BROTHA YOUR VIDEO DID IT! I HAVE NEVER EVER LIKED ANY VIDEO ON RUclips EVER!!! UNTIL NOW!!!! AFTER NUMEROUS VIDEO’S TO LEARN HOW TO CLEAR, PAIR AND LEARN WITHOUT SUCCESS, YOUR VIDEO DID IT!!!!* THANK U SOOOO MUCH MY G!!!!*
Watched at least 10 other videos and not one told me not to release A button after pushing A & B and then to hit the B button 3 times and finally All other codes were cleared. Very frustrating when you do what other videos tell what to do and it doesn't work. Thank you!
My stupid remote that has to copy the codes is not flashing at all at start when clicking A+B. It starts to flash after 5 seconds then long flashing. What the hell am I doing wrong?
Press A and B simultaneously until LED flashes thrice then release B while keep pressing A, then press B 3 times and you will see led flashing continously then remove hand from A now the remote will be erased from codes then press and hold A on the copy remote and then on the original remote. same for B
Reset and copy looks successful and it works fine for the very first time when I first press the button, but then it "forgets" the code and never works again unless I repeat the whole procedure. Any idea?
How do I connect a new original device. It seems I have two original remotes. One works. And the other doesn’t just replaced the batteries to start testing it
One original remote only (pairing) support automation devices, If you want to pair another one use a clone/copy remote that remote should copy the wireless frequency code from original remote.
@@FrancescoBaldacchini i figured. Turns out there was an issue with the C button. Something made it stay pressed and i had to remove it. Might be an imperfect contact somewhere.
Tried cloning my garage remote, and everything went as should, light on the cloned remote is solid blue, which tells me it has copied code but does not operate garage? any ideas ?
Hi, I tried to reset a Sonoff universal remote (433 Mhz) by pressing A+B button, but the led remains steady RED. How can fix it? Another question, how can I replace the battery ? thank you
With me, my garage door opens but does not close. And I can only open my garage door once, and when I close it again with my original remote and then want to open it again with the cloned remote it won't go I don't understand :(
I can go trough the first steps easily, but when I try to copy it the light flashes few times then stays on. Can’t seem to get it to flash rapidly. What am I doing wrong?
*BROTHA YOUR VIDEO DID IT! I HAVE NEVER EVER LIKED ANY VIDEO ON RUclips EVER!!! UNTIL NOW!!!! AFTER NUMEROUS VIDEO’S TO LEARN HOW TO CLEAR, PAIR AND LEARN WITHOUT SUCCESS, YOUR VIDEO DID IT!!!!* THANK U SOOOO MUCH MY G!!!!*
I'm glad you found the video useful, thank you for your kind words!
Watched at least 10 other videos and not one told me not to release A button after pushing A & B and then to hit the B button 3 times and finally All other codes were cleared. Very frustrating when you do what other videos tell what to do and it doesn't work. Thank you!
An actual tutorial video that is easy to follow and more importantly - works!!! THANK YOU!!
You're welcome!
you're the bomb bro!!!, I share the same sentiments as others before me, what a wonderful tutorial .
An excellent video! I have successfully copied my garage remote.
Thanks, exactly explained how to do it. Worked like charm
BEST of BEST clearly instructions, thanks 😊
Thank you very much my friend, you saved me a.major headache
Thank you for posting. These instructions are easy to follow.
Thank you for your video 😊
Excellent, thank you!
My stupid remote that has to copy the codes is not flashing at all at start when clicking A+B. It starts to flash after 5 seconds then long flashing. What the hell am I doing wrong?
I cannot reset the remote can you. Please help me with this it jus keeps flashing when I press any button from ABCD
Did you solve this? It’s happening to me too
Did any solution . Same with me
Press A and B simultaneously until LED flashes thrice then release B while keep pressing A, then press B 3 times and you will see led flashing continously then remove hand from A now the remote will be erased from codes then press and hold A on the copy remote and then on the original remote. same for B
Reset and copy looks successful and it works fine for the very first time when I first press the button, but then it "forgets" the code and never works again unless I repeat the whole procedure. Any idea?
Sounds like you need a rolling code fob.
Same problem here … anyone got a solution for this ?
same here... what could be the reason.... should I buy rolling code remote and do it again? is it available in Amazon? Is it pricey?
How do I connect a new original device. It seems I have two original remotes. One works. And the other doesn’t just replaced the batteries to start testing it
One original remote only (pairing) support automation devices, If you want to pair another one use a clone/copy remote that remote should copy the wireless frequency code from original remote.
Thanks for this video gets to the point and worked first time
Thank you! Very helpful.
You're welcome!
The IR LED is located in front of the remote, why not put both remote front to front to facilitate the copy process ?
Best video explains how to reset and recode this RC
Thank you. It works!
perfectly explained,thank you......
You are welcome!
thanks alot, im from Malaysia
You're welcome! Hope this helps.
I have a Vauxhall Vectra C. Will this work to copy my key for opening my doors and trunk? Thank you
Hi. My remote is continuously flashing and no combination of keys can stop this. Do you know what i can do?
same here
@@FrancescoBaldacchini i figured. Turns out there was an issue with the C button. Something made it stay pressed and i had to remove it. Might be an imperfect contact somewhere.
@@dianazamfirescu359what brand/model is that remote control they’re cloning onto?
An 433 mhz key could be cloned into a 355 mhz key?? Thanks
No, 355Mhz support 355Mhz clone/copy remote only
Thanks!@@Techlogics
Can you help? My remote is not ABCD; it is 1234. When I press anything, the LED flashes.
Tried cloning my garage remote, and everything went as should, light on the cloned remote is solid blue, which tells me it has copied code but does not operate garage? any ideas ?
Same problem here. Were you able to solve the problem?
Great video. It worked well . Thanks.
The best, thanks youuuu! ❤️🙏🏻
Can i do it without the remote copier device?
Just 2 remote can be cloned?
Awesome work!
Hi, I tried to reset a Sonoff universal remote (433 Mhz) by pressing A+B button, but the led remains steady RED. How can fix it? Another question, how can I replace the battery ? thank you
With me, my garage door opens but does not close.
And I can only open my garage door once, and when I close it again with my original remote and then want to open it again with the cloned remote it won't go I don't understand :(
Is it possible to concert it into a mobile application ?
Thank you finally someone with a brain lol
Can I use this for my car?
When i try to clear the codes off the new remotes they won't clear by pressing the 2 top buttons no matter how lo g i hold them! Plz help
Hold them together for few seconds than realise one button and keep presing other one, then realised button press 3 time while holding pressed button
I can go trough the first steps easily, but when I try to copy it the light flashes few times then stays on. Can’t seem to get it to flash rapidly. What am I doing wrong?
I press A and B at the same time and it will not blink. The LED stays solid.
Make sure your remote model should be copy/clone type remote. Or try C & D Button
No clue how this works. What is the copy button ? Got 4 units. Mom is working.
thank you so much
How can I make master remote to work all remote
thaks, woked for me
When i clicl A+B, it keep gives me continous blue light without flashing no matter yime of clicking 😮
Easy instructions. Thank you.
Thank you
Is there a way to add a new code without having to delete all the codes previously installed?
I want to know too, did you find out?
i can not reset the remote
I have the same problem
Make sure the remote is clone/copy compatible remote
J'ai besoin une démonstration d'une amc
Mer
El mando falla no funciona