Amazing work as always! Even if I may not be constantly present, I’ll do my best to support the railfanning community as much as possible. I’m greatly thankful for your fantastic work and passions that you put your dedication to. Keep enjoying on what you are striving for, and continued wishes for the outcomes that you desire for! Hope you and your family had a great Thanksgiving! 🚂👍🍂
I have OCD and that would drive me crazy too have to do that just a suggestion maybe put a wireless cam on the ceiling above the turn table or just type it in twice for all the times you switch but a pain in the butt anyway hope you can sort it out or the people replace it with a new one for the grief you have gone through good luck and happy rails to you 🚂💯💔
Thats a good idea with the camera on the ceiling to help monitor the bridge track position. Also, a great suggestion to type it in twice. The only thing that worries me about that is that it can possibly get progressively worse. I would like to think that it should work right the first time, but I will definitely try your suggestions. thanks!
Just a guess, is the voltage feeding the table correct? Might be slightly low and motor and electronics not operating there best. Good ground always important. Impressive table.
Great suggestions Joey! I actually checked this out before and the voltage is good. I also checked the ground wire, and it is connected properly. Thanks, I will continue testing everything I can think of and continue troubleshooting. Hopefully I can find a solution soon!
That is very disappointing after you already took it out and sent it back. I’m no expert. But from your testing. It seems like the circuit assembly might be working correctly. I wonder if the problem is mechanical. Again I’m no expert. I look forward to your end results.
Yes, this is very disappointing. I agree with you that it probably is mechanical, although I am not sure what it can be at this time. I will continue testing it and hopefully find out what's causing the issue and try to resolve it if possible. I will make a follow up video if I have any results sometime soon. Thank you for your suggestion!
Please understand these tables cost approximately $2,500 with all of the features and are supposed to be built to last. Yet, this table had this issue from the beginning, and it is only 3 years old and rarely used. Also, this turntable just came back from the factory, so it should work properly. To answer your question, I find this situation very disappointing, and I am not so sure that I would be so quick as to purchase another one again. At this point, I think I will just keep testing it and hopefully find a solution very soon. Thanks for your comment!
I agree you should not have program it twice.I hope you get it fixed
Exactly, somethings not right. Thank you very much!
Wow, George, that sucks. Why it finds it a second time correctly, but not first? Too weird!
Hey Anthony, yes this totally sucks! It doesn't make any sense.
They should totally replace your turntable. The proof is in your video. 👍
Yes I agree Jim, that would be the right thing to do!
I have a good lawyer if you need one. He specializes in train derailments for miniature train layouts.
Amazing work as always! Even if I may not be constantly present, I’ll do my best to support the railfanning community as much as possible. I’m greatly thankful for your fantastic work and passions that you put your dedication to. Keep enjoying on what you are striving for, and continued wishes for the outcomes that you desire for! Hope you and your family had a great Thanksgiving! 🚂👍🍂
I have OCD and that would drive me crazy too have to do that just a suggestion maybe put a wireless cam on the ceiling above the turn table or just type it in twice for all the times you switch but a pain in the butt anyway hope you can sort it out or the people replace it with a new one for the grief you have gone through good luck and happy rails to you 🚂💯💔
Thats a good idea with the camera on the ceiling to help monitor the bridge track position. Also, a great suggestion to type it in twice. The only thing that worries me about that is that it can possibly get progressively worse. I would like to think that it should work right the first time, but I will definitely try your suggestions. thanks!
Happy rails to you as well! 🚂🚂🚂
Just a guess, is the voltage feeding the table correct? Might be slightly low and motor and electronics not operating there best. Good ground always important. Impressive table.
Great suggestions Joey! I actually checked this out before and the voltage is good. I also checked the ground wire, and it is connected properly. Thanks, I will continue testing everything I can think of and continue troubleshooting. Hopefully I can find a solution soon!
Who makes the turntable?
That is very disappointing after you already took it out and sent it back. I’m no expert. But from your testing. It seems like the circuit assembly might be working correctly. I wonder if the problem is mechanical. Again I’m no expert. I look forward to your end results.
Yes, this is very disappointing. I agree with you that it probably is mechanical, although I am not sure what it can be at this time. I will continue testing it and hopefully find out what's causing the issue and try to resolve it if possible. I will make a follow up video if I have any results sometime soon. Thank you for your suggestion!
Can you buy a new Turntable
Please understand these tables cost approximately $2,500 with all of the features and are supposed to be built to last. Yet, this table had this issue from the beginning, and it is only 3 years old and rarely used. Also, this turntable just came back from the factory, so it should work properly. To answer your question, I find this situation very disappointing, and I am not so sure that I would be so quick as to purchase another one again. At this point, I think I will just keep testing it and hopefully find a solution very soon. Thanks for your comment!
I understand Is there expensive
Is your temple of millhouse turntable