Before insert icopy as single sketch assembly, you can create inside one single frame with whatever profile inside, applying notch, holes, miter, etc. and only after insert icopy frame in your final assembly. Doing that, all features as miter, hole, notch will be applied on each new created frame.
Excellent Professor! I thought It was going to be an impossible task but I actually drew it in about one hour. I have to keep pausing and going back. Lots of commands there! Regards, Daniel Valbuena
Foarte bun tutorialul! Plus ca aveti un stil mai clar si la obiect fata de multe alte tutoriale de pe RUclips, unde unii vorbesc poate si 2 minute ca sa faca un "extrude" :) Ma bucur ca sunteti in continuare activ pe internet si va doresc sa fiti in forma maxima multi ani de acum incolo... Multa stima, domnule Profesor!
Dear Constantin, I spent 2 days on this task but I made it. Good excercize. It would be interesting in continuing in framning in celling and floor in order to keep constraction ...not collapce e.g. in winter under snow coverage. Best regards Jan
Dear Constantin, I made some modification of your case. I construct a frame also trough floor and ceeling. I did frame analys with following results " displacement in middle of roof 57 mm and Smax 98 Mpa. Some question for you: 1. Does inventor calculate in gravity load alsou weight concreate cealing? The total weight of concreate ceeling to be 55 t. 2. Is frame analysis proper tool to use it in this case? I do not know how to load weight of snow. Thank you. Best Regards from Prague Jan
Super lessons, I watch with pleasure. You can further develop iCopy. Let's say a semicircular chair and you need to make racks that go from the bottom to the top of the backrest. All radii are different and the upper part is tilted. I tried it, but it didn't work out. Will you succeed?
@@dshubad Yessss you are right! The sequence of the movie from 9:37 to 10:17 is repeated starting from 10:17. It is my mistake, thanks for observation!
@@prof-stancescu Don't mention it )) Please help with advice. We have a task. We have to calculate the area of the faces to which a certain material is applied. What tools are there to do this? Maybe there is a lesson about this?
Before insert icopy as single sketch assembly, you can create inside one single frame with whatever profile inside, applying notch, holes, miter, etc. and only after insert icopy frame in your final assembly. Doing that, all features as miter, hole, notch will be applied on each new created frame.
Thank you, my friend!
"Engineers, be aware!
From the architects, you can expect anything..."
I love it! 30 years of my working life has brought wisdom to this quote. :)
👍
Excellent Professor! I thought It was going to be an impossible task but I actually drew it in about one hour. I have to keep pausing and going back. Lots of commands there!
Regards,
Daniel Valbuena
Excellent!
Dear Prof Constantine. I'm So Glad to learn CAD in Inventor especially at your RUclips Channel
Glad to hear that!
Dear Constantin
Thank you very much for a very informative tutorial. It has been of great benefit to me.
Glad it was helpful!
Great tutorial, very easy to follow!
Glad you think so!
Foarte bun tutorialul!
Plus ca aveti un stil mai clar si la obiect fata de multe alte tutoriale de pe RUclips, unde unii vorbesc poate si 2 minute ca sa faca un "extrude" :)
Ma bucur ca sunteti in continuare activ pe internet si va doresc sa fiti in forma maxima multi ani de acum incolo...
Multa stima, domnule Profesor!
Mulțumesc! Mă țin în formă maximă cu 148 de tutoriale în mai puțin de 6 luni...
V-am trimis de azi dimineață Albumul (PDF) prin WeTransfer, dar se pare că sunt probleme cu adresa Dvs. de e-mail!
Dear Constantin, I spent 2 days on this task but I made it. Good excercize. It would be interesting in continuing in framning in celling and floor in order to keep constraction ...not collapce e.g. in winter under snow coverage. Best regards Jan
Go ahead - learn and enjoy!
Dear Constantin,
I made some modification of your case.
I construct a frame also trough floor and ceeling.
I did frame analys with following results " displacement in middle of roof 57 mm and Smax 98 Mpa.
Some question for you:
1. Does inventor calculate in gravity load alsou weight concreate cealing? The total weight of concreate ceeling to be 55 t.
2. Is frame analysis proper tool to use it in this case? I do not know how to load weight of snow.
Thank you.
Best Regards from Prague Jan
Very cool! Thank you very much for uploading!
Glad you enjoyed it!
Super lessons, I watch with pleasure.
You can further develop iCopy.
Let's say a semicircular chair and you need to make racks that go from the bottom to the top of the backrest. All radii are different and the upper part is tilted. I tried it, but it didn't work out. Will you succeed?
Let me see a picture, some dimensions...
@@prof-stancescu And where should I send it? You have no information about the communication method in the channel description.
@@prof-stancescu drive.google.com/file/d/1xjEEGsPxyh_Vyc1zfg6vTct8ULSvuVJh/view?usp=drivesdk
@@prof-stancescu I will be very grateful to you if you record a video. I think the rest of the audience will appreciate it.
Superb tutorial Sir. Thanks
Glad you liked it
That was very cool!!
Thank you!
Thank you so much!!!
Go ahead - learn and enjoy!
impressive with Inventor, should learn it. Thank you
Please do!
Very very good job 👍🏻
Thank you very much
Thanks.. For Your Class.. it Was Very Good
Thanks and welcome
Matur suwun 🙏
(Thank you) I thank you also...
10:17 Повторяется создание сборки.
(The assembly is repeated) Where do you see the repetition? What minute of the movie?
@@prof-stancescu Good evening 9:37 and 10:17
@@dshubad Yessss you are right! The sequence of the movie from 9:37 to 10:17 is repeated starting from 10:17. It is my mistake, thanks for observation!
@@prof-stancescu
Don't mention it ))
Please help with advice. We have a task. We have to calculate the area of the faces to which a certain material is applied. What tools are there to do this? Maybe there is a lesson about this?
Well, now this mistake was eliminated - please verify!