It's a good sign for me! Thank you man great video my dad fell ill the beginning of the year so hes unable to help me but this video saved me haha thanks again!
If one barely spins and starts smoking you need to swap the stator/motor housing right? Is that not very difficult to do? I saved one from the dumpster.
Aman Tek I think when you switch between drill only and hammer only your meant to put the switch to drill/hammer pull the trigger then switch it to hammer only. Fucks up over time it switching straight from drill only to hammer only. If that makes sense.
Great video! I have a Makita DHR263 Z and it is not spinning-rotating,hear some noise,spins a little and stops.What do you think is the probable cause of the problem? Will try to take it apart following your video.
Hi I have the same problem but I was not unable to remove my mode selector switch like you. It was difficult to see what you did exactly. 1. Switch to hammer mode, 2.then press switch in and move just past hammer mode. 3. Did you just pull the switch out? My switch doesnt want to come out at all. Yours just popped out then popped back in after the repair?
Did you get it out? It can be very stiff. Turn it to the hammer only setting then gently wrap a wrench round it for some leverage, press the button in and then turn it clockwise further 4-5 mm. then it will prize out. There is a rubber o ring on it which seals it and makes it stiff. To put it back do the process in reverse but you might have to gently tap it back in to overcome the friction of the rubber o ring. Handyman’s came out very easily I wonder if rubber o ring was not present.
Thank you very much for your video. It helps a lot. I fixed the drill. Is any chance you can make video of makita 8406c gear box repair? Also just would like to ask you where are you from? Thank you again.
Hello, thank you. I think I will not get Makita 8406C because I'm from Lithuania and it's not in oir market. If you are from EU, you can send it to me and I will check it and make video about it...
It's a good sign for me! Thank you man great video my dad fell ill the beginning of the year so hes unable to help me but this video saved me haha thanks again!
Just fixed my own DHR242 following this video👍
Great! Another good video from Handyman - time for a coffee and relax to watch. :-)
Thank you 🤓
Very useful video for you to do with more machine tools
If one barely spins and starts smoking you need to swap the stator/motor housing right? Is that not very difficult to do? I saved one from the dumpster.
I have exactly the same issue.
Great, thanks.
good work (y)
Thank you!
Nice
Thanks
Thanks for this great video. Where did you order the gears from?
Where did you buy a new mode selector pin?
Thanks
My dhr242 won't hold any bits. I changed my chuck for new one still the same. Advice?
what parts do i need to change if only drill mode runs others don t ?
Always great videos! You always sound like you have a cold or maybe a little coke 😜
Es igual
I have the same sds drill the selector switch struggles to go to the hammer mode, i woud have to force it, what do you think it might be?
Aman Tek I think when you switch between drill only and hammer only your meant to put the switch to drill/hammer pull the trigger then switch it to hammer only. Fucks up over time it switching straight from drill only to hammer only. If that makes sense.
I'm having this issue too any thoughts?
Great video!
I have a Makita DHR263 Z and it is not spinning-rotating,hear some noise,spins a little and stops.What do you think is the probable cause of the problem?
Will try to take it apart following your video.
where i can buy these parts? can you please provide a link?
Hi I have the same problem but I was not unable to remove my mode selector switch like you. It was difficult to see what you did exactly. 1. Switch to hammer mode, 2.then press switch in and move just past hammer mode. 3. Did you just pull the switch out? My switch doesnt want to come out at all. Yours just popped out then popped back in after the repair?
Hello, do you have same model? Maybe you have DHR202? Then you can check HR2470 videos - switch removing method is different for DHR242 and DHR202...
Did you get it out? It can be very stiff. Turn it to the hammer only setting then gently wrap a wrench round it for some leverage, press the button in and then turn it clockwise further 4-5 mm. then it will prize out. There is a rubber o ring on it which seals it and makes it stiff. To put it back do the process in reverse but you might have to gently tap it back in to overcome the friction of the rubber o ring. Handyman’s came out very easily I wonder if rubber o ring was not present.
Chilled Heat International I wrote you a tip below to get switch selector out.
Cómo se llama la grasa que usas??
Hello, I use Makita greaase for hammers. amzn.to/2SWHqvj
Gracias amigo !!!;
Gracias amigo !!!;
Dónde te puedo mandar mí taladro
Gm morning sir I need to get intouch with you interested in buying use parts armature etc
Thank you very much for your video. It helps a lot. I fixed the drill.
Is any chance you can make video of makita 8406c gear box repair?
Also just would like to ask you where are you from?
Thank you again.
Hello, thank you. I think I will not get Makita 8406C because I'm from Lithuania and it's not in oir market. If you are from EU, you can send it to me and I will check it and make video about it...
Шта?