Thank you so much Pankaj ji for Repairing my aquasure pcb alright and send it back immediately to my place though it is other state.v trust worthy. Thank you once again 🙏🙏
I have aquaguard infiniti model. After clicking the free flow button red light is blinking. I checked sensor and uv lamp is ok. But from PCB 12v not getting to sv valve. So which part to change in pcb board? Pls guide me. If I want to send the board to you what is the procedure?
I have an aquaguard genus to. The blue service light is flashing and water is not coming out. I changed the pcb but did work only for 3 months and the same problem again appeared. How to repair the pcb and what goes wrong with it ? Can someone help ?
Please tell me what will be the issue when pump terminal voltage is 24 before applying load(before connecting pump) and after connecting pump is zero(showing fault 4 in the display) model is Eureka forbes aqua sure xpert 8L
mera inova machine hai transformer wala sensor change karne ke bad bhi circuit on nahi ho raha hai uv on ho rah hai led red sey orange ho raha hai lekin green nahi ho raha
@@waterpurifier_pcb-repair capacitor pe 300volt ban rahe h but 10volt nahi aa raha mene viper22 aur optocupler bhi change kiya sare diode bhi check kiye sub ok h fir bhi bada wala diode pe +10volt nahi aa raha
Sir I am Eureka Forbes technician ... Sir I have dout on PCB .. pcb complete died ...if we check on testing machine .. that time Fuse will .spark ... .plz tell how to check PCB ... 🙏🙏🙏
Sir problem mil gaya usme uv light ke liye jo smd MOSFET lagaya hai vo short hai...MOSFET board se nikalne ke baad circuit ka buzzer sound chalu ho gaya hai ....Sir please mujhe vo MOSFET ic ka no do....
Same pcb Pahale 2 Fuse open hogaye Change kiya to sirf power ic jalgayi Ab change kiya ic to firbhi bord on nahi horaha he our red light bhi on nahi ho rhi he....
सप्लाई हमने चेक किया लेकिन सप्लाई कहीं से समझ मैं नहीं आ रहा है और तीनों लाइट साथ में बिलिंग कर रहा है क्या करना होगा मैंने सब जीना डायोड भी ओपन करके देख लिया वोल्टेज नहीं आ रहा है
नमस्ते सर बारह साल से Aquaflow dx का उपयोग कर रहे हैं। कल जब चालू किया गया, तो पीली बत्ती चालू थी और हरी बत्ती झपक रही थी और बीप बिना रुके बज रही थी और पानी नहीं मिला था। PCB में कोई समस्या नहीं देख सका। क्या आप कृपया मुझे समाधान बताएंगे?
Very nice video can you please let me know why the power supply IC has blown off ? Will replacing the IC work ? Or should I check for other components please help thanks in advance .
Thank you so much Pankaj ji for Repairing my aquasure pcb alright and send it back immediately to my place though it is other state.v trust worthy. Thank you once again 🙏🙏
Could you please reply the transformer rating/spec for TX1
Pureit Ultima Uv + Ro ma motherboard repairing hoga?
I have aquaguard infiniti model. After clicking the free flow button red light is blinking. I checked sensor and uv lamp is ok. But from PCB 12v not getting to sv valve. So which part to change in pcb board? Pls guide me. If I want to send the board to you what is the procedure?
Sir pure it ultima ro me pcb me pump par 24 volt DC output nhi aa rhi h
Use full video.Thank u
Sir ji 300 volts AC mey aana chahiye na
viper 22 replacement ..its always duplicate and fires every time..to overcome this problem i usually buy a dth power supply and salvage the ic..
Power ic,opto coupler, changed and all diodes & capacitor are ok 300 volt available but 10 volt not available.Please advice what next?
Check any short in out put
@@waterpurifier_pcb-repair
Ok
Hello sir
AC filater chok bad jo bridge circuit banti usme daiod 4007 ho ta hi ya agal bhi ho sakta he
Pls elaborate
Is pcb replacement covered in AMC of aquaguard?
Yes
Problem Resolved
Thank You
I have an aquaguard genus to. The blue service light is flashing and water is not coming out. I changed the pcb but did work only for 3 months and the same problem again appeared. How to repair the pcb and what goes wrong with it ? Can someone help ?
Sensor or uv lamp defect
Sir namaste. Plz make a video on your testing jig with full details. Thank you sir
I need to repair my filter pcb where this repair or new pcb from where i got plese give me reply
Please contact me if repair or new pcb
Please tell me what will be the issue when pump terminal voltage is 24 before applying load(before connecting pump) and after connecting pump is zero(showing fault 4 in the display) model is Eureka forbes aqua sure xpert 8L
Change pump
@@waterpurifier_pcb-repair pump is new but still it is showing fault only. I had paid for 1 year AMC and then they have changed pcb, pump, cartridges.
Kindly show if possible how to repair PCB of : Pure It Marvella RO+ UV with RTC based GKK ASO & booster pump
I m not pure it service provider
If u send me d pcb then I can help
My number 8917341707
mera inova machine hai transformer wala sensor change karne ke bad bhi circuit on nahi ho raha hai
uv on ho rah hai
led red sey orange ho raha hai lekin green nahi ho raha
bhai mera aquaguard verve hai, woh maine 6-7 ghante ON rkha tha toh woh ab start nhi ho rha hai, service wale ko bulaya toh woh 2100 rupey le rha pcb board change krne ke, kya yeh price sahi hai?
1600 +service charge.
If u send me i can repair pcb
Sir, Viper 22A ic is shorting again and again of aquasure PCB please suggest solution
Use original
Sir repair karne se pehle or repair karne tak ki video banaya kare kis kami se aye hai ye sab detail bata kare
Sir sirf is pcb me220v ac denge to uv lamp on ho gaye ga kiya
Yes
Power supply ok hoga to hi on hoga
My model is aquaflow DX model
Mera pcb ka TFT-2 no transformer short hai muje new pcb lena hai kaha milegi
Service centre
sir mera aquasure dx uv model ka ro h..uska red light blink kar raha h dim..beep bhi nahi kar raha..kya problm ho sakta h
Check 230volt on pcb .
And then 10volt.
@@waterpurifier_pcb-repair capacitor pe 300volt ban rahe h but 10volt nahi aa raha mene viper22 aur optocupler bhi change kiya sare diode bhi check kiye sub ok h fir bhi bada wala diode pe +10volt nahi aa raha
10 volt constant nahi hai kabhi 7v horaha hai kabi 15-16v
Sir I am Eureka Forbes technician ... Sir I have dout on PCB .. pcb complete died ...if we check on testing machine .. that time Fuse will .spark ... .plz tell how to check PCB ... 🙏🙏🙏
Check power ic short.
Sir, I want to repair my PCB board I am staying in Mumbai Bandra which is the closest shop for me please tell me.
Contact nearest retailers for service.
Retailer do not repair.. they prefer new pcb installation...
aquasure maxima booster ki pcb me power ic ka kya number he
Viper 22
Sir I have old aquflo pcb fault is yellow light blinking UV lamp not working can you tell me what will be the problem
Sir apne replay nahi diya Kya kare
Yellow light blinking ho raha hai
Change PCB I think it cost 900 rs new and repair 600 rs u get on Eureka Forbes office near Ur home
Geneus front pcb chip repair kaise kare bhai
Bhayya, where is the service center in visakhapatnam Aquaguard aqua flow Dx pl give me info
odisha
Sir, is ckt me uv part me jo mosfet he o kharap hogaya me konsi mosfet lagauplz. Help me
Number printed on it
aquaguard ke pcb me microcontroller pograming kaise kiya jata hain?plz iske upar ek vdeo banayee....
No solution
Agar Jaise ismein shorting a Raha hai sar apna series light direct jal rahi hai to sar kya shot ho sakta hai
Series light me short nahi hoga
Spair part Kaha milega
New Kaha milega sir
Sir same pcb hai mere pass usme problem y hai ke front me jo 3 light hote hai na wo blink hora hai air pani ruk gaya hai
Power issue
@@waterpurifier_pcb-repair sir all diodes, zenerdiode, and resistor ok
@@waterpurifier_pcb-repair power ic change karu ya smd me koi problem hai
My pcb Tx1 1430 muje replace karana hai kahamilega abhi adapter supply se chalu hai pcb Bypass kiya hai ye tik hai
Which model
Aquasure aquaflow DX model
Mere paas Aquaguard ka INFINITI model hai aur fuse blow ho raha hai. Is ki repair batayein.
Primary section short
Good
Sir ji yello light nahi aa raha hai but uv lamp chalu hai kya problem hai surkit me
processor is not working
Sir viper 22A ic change karne par bhe 10volt nahi bante hai to kya problem ho sakta hai.
Change aupto coupler.817
Sir vo bhe change kiya par out put me 10volt nahi aa rahi hai
@@waterpurifier_pcb-repair viper 22A ic ke pin 4 par bhe 14volt aa rehi hai or pin 3 par bhi 0.1 volt aate hai
Sir problem mil gaya usme uv light ke liye jo smd MOSFET lagaya hai vo short hai...MOSFET board se nikalne ke baad circuit ka buzzer sound chalu ho gaya hai ....Sir please mujhe vo MOSFET ic ka no do....
Infinity smps pura det हे kya problam ho
saktahe
ᑕᕼEᑕK ᑭOᗯEᖇ ᔕᑌᑭᑭᒪY
Uv section me bhi 1 videos banav
Same pcb
Pahale 2 Fuse open hogaye
Change kiya to sirf power ic jalgayi
Ab change kiya ic to firbhi bord on nahi horaha he our red light bhi on nahi ho rhi he....
How I can buy universal pcb testing jig
Not available
10v uppar tala hela kan kari ba
Pcb work kar raha hai par sv oprate nahin ho raha hai, kaise thik karen
Naya board ka cost kitna hein? Kaha milegi
Pcb rs 1500 new
Optocopular IC par voltage nhi aa raha hai or man capicitor par 300voult se jayada voltage aata hai kya problem ho sakta hai
Power ic defect
Power ic lod kane se pehle 330 volt ata hai to problem kya hai sir ji
Ic lod kar sakte hai
Pcb chalu hota hai lekin ic garam hotI hai sir ji kya problem ho skta hai
Aqua flow me Red led glow hokar kuch second's ke liye UV glow hota jai phir turant led red ho jata hai air Beep horta hai
Send me d video
Yadi 10v k jagah par 20v as Raha hai to kya kare pls suggest
SV turning on continuously even when flow switch is kept off.
Change sv
Problem is in PCB SV connecter pe supply ata jata ha I
Sv change hua hai mere ok jig pe check Kar raha hu.
Hi sir how to get universal Pcb testing jig
Not avlavle .only from company
sir where is your workshop
Odisha
Yellow led blinking and beeping sound kiya problem he
Tub (uv) jelthahe but thuran off hothahe
Uv lamp or pcb
Water supply 12 volt nayi athaha
Yellow light blinking and beeping sond be he
Pcb konsa parts kharab hoyeka
Aqua sure maxima model,
का प्रोब्लेम है,plZ मदद दो,
ग्रीन लाईट blink करता है,water फ़्लो नही होता,
Low pressure water
Mine is giving continuous beeping.... Water purifier working fine but with continuous beeping.... Solution please
Buzzer continuously beeping *
Uv lamp,it's wires , or pcb fult
Want to Repair aquagurad
Ur location
Sir is model me red and yellow light blink ker rahi hai
Check uv
Ok sir thanks
Apna soap n btao m.n v
Do more videos
New PCB kaha milegi
Service center
Cold sent no
Sir isme transformer pcb repairing ka video bhi daliye please
UV lamp supply khas karake
Ok
, अपलोड डी एक्स में पीसीबी चालू नहीं होती तीनों लाइट साथ में बिलिंग करता है रेड ऑरेंज और ग्रीन और 10 वोल्ट नहीं आता है तो क्या प्रॉब्लम हो सकता है
Check power supply
सप्लाई हमने चेक किया लेकिन सप्लाई कहीं से समझ मैं नहीं आ रहा है और तीनों लाइट साथ में बिलिंग कर रहा है क्या करना होगा मैंने सब जीना डायोड भी ओपन करके देख लिया वोल्टेज नहीं आ रहा है
@@Choudharychacha1987
Send me I will repair and send u
PCB cord DC v Ac voltage kaise function check kare
Check 300v on capacitor
New pcb ka price kitna hai
1600
@@waterpurifier_pcb-repairBahot jyada bata raha hai
Mera v PCB kharab hai
नमस्ते सर बारह साल से Aquaflow dx का उपयोग कर रहे हैं। कल जब चालू किया गया, तो पीली बत्ती चालू थी और हरी बत्ती झपक रही थी और बीप बिना रुके बज रही थी और पानी नहीं मिला था। PCB में कोई समस्या नहीं देख सका। क्या आप कृपया मुझे समाधान बताएंगे?
Send fult video on whatsapp
हमारे एक्वागार्ड ऑन करते ही फ्यूज उड़ता है क्या करे? आपका फोन मिल सके तो अच्छा है ।
8917341707
Whatsapp only
Number kya hai
Sir ji 330 volt ata hai 30 volt jyada kyon ata hai
No problem
@@waterpurifier_pcb-repair ok sir ji , thank you .
Kent bcb ko riper karana shi Khao.
I revive mostly aquaguard pcb,if I revive kent pcb I will make video
Pcb on ho raha hai but sv terminal men current supply nahin ho raha hai solution batayen
Check flow switch
Flow switch direct kiya hua hai
hello bro can you give me the power supply ic no please
Viper 22a
Very nice video can you please let me know why the power supply IC has blown off ? Will replacing the IC work ? Or should I check for other components please help thanks in advance .
Hi mera PCB ko repir karna hai
Send me
Kaha bheju
@@santoshpatil-le8pd
Contact me on whatsapp
Hi
Hello
Please send me the power IC number of aquaflow dx circuit.
Viper 22
Thanks
power ic number pls?
Ami repairing korte chai, pls your phone number... Kolkata... Paikpara... 35
Number Kay hai aap ka
Check in description
give me namber
8917341707
Good