Размер видео: 1280 X 720853 X 480640 X 360
Показать панель управления
Автовоспроизведение
Автоповтор
I'm learning this for the first time,but I am a mechanic in Light vehicle
Thank you , I will need this video next two days , same problem in my 3CX
Gostei da manutenção 🤝👏👏👏🇧🇷
Obrigada.
Que vídeo bem feito gostei muito
Bravo.maestro
Good video bro
You are great
Хоть русский, хоть не русский человек, всё равно всё мажет ПАЛЬЦЕМ, герметик, хоть смазку...
Матерится наверняка так же НО по своему .
Мазать не нужно, кольцо резиновое великолепно держит...
You should heat bearing before assembly. It will be easier to put it on shaft.
What would you need to heat it with. A hot air gun, in an oven or with a gas flame?
@@ashleysomerville2509 There are several methods. The best solution is to use bearing heater that allows to heat bearing to particular temperature.
very wonderful
Very good video, very detailed thank you, little to much silicone doe.Best regards
Adammm
Good working 👍👍👍
Donde comprar repuestos para jcb 3cx modelo 1989
slovakia.hydrob sk.ndstrojov.sk
Kedves Laci!Van e olyan Videótok amely a vàltórol szól?Üdvözlettel
Gud
Shir mero ko bhi jcb mecnik ka bija mile ga
Hammering a dry bearing that a no no You heat up the bearing goes on a lot easier
Не нужен там герметик. Сальник не стал на место. Пыльника нет(
Nao precisava nem retentor, foi tanto cilicone que isso nao vaza óleo nunca mais kkķkkk
how much kg/cm 2 torque
Rumuński Jarek Ogarek pokazuje jak nie naprawiać koparki. Paproch na medal
Ковш покрасить не забыл. а нож не поменял(
Bearing size please?
BEARING 907/50000 SEAL DUAL LIP 904/50021 127x160x15,5/17,5 mm O RING 828/00196
@@lacibatoch1673 how much torque
What's bearing type used for replacement?
Ložisko nápravy jcb 907/5000 ARB 37 425.37 625
Oil seal sizes please??
Niestety naprawa źle wykonana, brak osłony przed uszczelniaczem spowoduje dostanie się piachu czy czegokolwiek i wyciek od nowa.
The seal should be put into the hub not as you have done and also the seal should not be run on top of a coat of paint. Bad practice.
9:06 Miért nem melegítetted meg egy kicsit a csapágyat és akkor kalapálás nélkül is rá ment volna a tengelyre
Így is könnyen ráment,nincs szoros kötése.
no mécano ... bricoleur 👎🏼😂😂
I'm learning this for the first time,but I am a mechanic in Light vehicle
Thank you , I will need this video next two days , same problem in my 3CX
Gostei da manutenção 🤝👏👏👏🇧🇷
Obrigada.
Que vídeo bem feito gostei muito
Bravo.maestro
Good video bro
You are great
Хоть русский, хоть не русский человек, всё равно всё мажет ПАЛЬЦЕМ, герметик, хоть смазку...
Матерится наверняка так же
НО по своему .
Мазать не нужно, кольцо резиновое великолепно держит...
You should heat bearing before assembly. It will be easier to put it on shaft.
What would you need to heat it with. A hot air gun, in an oven or with a gas flame?
@@ashleysomerville2509 There are several methods. The best solution is to use bearing heater that allows to heat bearing to particular temperature.
very wonderful
Very good video, very detailed thank you, little to much silicone doe.
Best regards
Adammm
Good working 👍👍👍
Donde comprar repuestos para jcb 3cx modelo 1989
slovakia.hydrob sk.ndstrojov.sk
Kedves Laci!
Van e olyan Videótok amely a vàltórol szól?
Üdvözlettel
Gud
Shir mero ko bhi jcb mecnik ka bija mile ga
Hammering a dry bearing that a no no You heat up the bearing goes on a lot easier
Не нужен там герметик. Сальник не стал на место. Пыльника нет(
Nao precisava nem retentor, foi tanto cilicone que isso nao vaza óleo nunca mais kkķkkk
how much kg/cm 2 torque
Rumuński Jarek Ogarek pokazuje jak nie naprawiać koparki. Paproch na medal
Ковш покрасить не забыл. а нож не поменял(
Bearing size please?
BEARING 907/50000 SEAL DUAL LIP 904/50021 127x160x15,5/17,5 mm O RING 828/00196
@@lacibatoch1673 how much torque
What's bearing type used for replacement?
Ložisko nápravy jcb 907/5000 ARB 37 425.37 625
Oil seal sizes please??
Niestety naprawa źle wykonana, brak osłony przed uszczelniaczem spowoduje dostanie się piachu czy czegokolwiek i wyciek od nowa.
The seal should be put into the hub not as you have done and also the seal should not be run on top of a coat of paint. Bad practice.
9:06 Miért nem melegítetted meg egy kicsit a csapágyat és akkor kalapálás nélkül is rá ment volna a tengelyre
Így is könnyen ráment,nincs szoros kötése.
no mécano ... bricoleur 👎🏼😂😂