I take it the front lower bumper couldn't take the rub, thus the new bar on the front? Thinking about shipping a 4 incher to Australia for my '19 XLT to run 35's. Would love to not have to wait for a second shipment of a front bullbar and ship it with the suspension if that's the case...?
What are the wheels and tires please? What would this all cost,...parts (lift, wheels/tires) and labor? I'm going to be driving to phoenix from New Mexico to get this done by you guys. I've purchased Mustang parts from you guys and always had top notch customer service. Also,...military discount for active duty by chance?
Has anyone done this lift on 2019 F150 I read that if you put a 4 inch block which the kit comes with you still might say hi in the rear I might try at three I wouldn’t mind it being down a little bit in the back
305/70R18 Mickey Thompson Baja ATZ P3 Tires and Method 18x9" Double Standard Wheels with 18mm offset and 5.75" backspacing is what our wheel/tire setup was. We did not experience any rubbing. Give us a call or check with BDS if you go bigger to make sure you wont experience rubbing on your setup. 623 434 5277
hi stage3motorsports. I was wondering if this kit had anything that would get in the way of my magnaflo side exit exhaust. it is the sane side exhaust kit you guys sell
The axles are at an angle since the truck is suspended in the air on a lift for the install. The lift kit itself includes the front differential drop brackets to relocate the differential and axles to the correct angles
Would I run into any issues running 20X9's on a 4 inch lift? I'm trying to fit 35's with 20's without having to trim anything or lift the truck too high. If not what lift would you recommend?
+jimmy ortiz You can do that on a level with the new f150, the only issue would be the crash bars if your wheels have a low/negative offset. www.f150forum.com has a ton of info you can search on this
I leveled with 35x12.5 on a -12 rim. I had to cut the crash bars to stop the rubbing. Its a street queen in this set up but if you want performance go 4 or 6inch lift and 35s
@Thamac15 You can find out everything about this build here, www.stage3motorsports.com/Stage3s-2015-F150-5-0L-Desert-Runner-Project-Truck.html For install cost, call us at 623-434-5277
@@stage3motorsports some cheap rustolem spray paint goes a long way. I was looking for shops to help me set up an overlanding truck, and the truck would spend time on trips more that just in AZ. Its a simple thing to do to show a bit of pride in your work.
Alec S cutting the crossmember does nothing for angles, it just allows you to drop the front differential to fix the cv angles. In fact 2wds don't have to cut the crossmember
henceforth fixing the angles that you just stated. and you need to have your tie rods at a certain angle or the stress would cause premature failure of the tie rod ends, also the more extreme angle can damage them during full suspension cycling
cant wait to get mine installed! placed my order with Lou a few days ago
You'll love this kit! BDS and Fox are a winning combo
NEED MORE VIDEOS of BDS EQUIPPED F150s in ACTION!!!
What size tires are those and what size rims?
Love this set up.
Love BDS Lift kits.
What color is this truck to?
@@billpeirce7456 Well Bill, Survery says: Shit Brown Color
At 9:12 mark . . . . yeah . . . . . he just stripped that one.
0:25 are you really lifting the truck from the nerf bars?
I take it the front lower bumper couldn't take the rub, thus the new bar on the front? Thinking about shipping a 4 incher to Australia for my '19 XLT to run 35's. Would love to not have to wait for a second shipment of a front bullbar and ship it with the suspension if that's the case...?
What are the wheels and tires please? What would this all cost,...parts (lift, wheels/tires) and labor? I'm going to be driving to phoenix from New Mexico to get this done by you guys. I've purchased Mustang parts from you guys and always had top notch customer service. Also,...military discount for active duty by chance?
Did this truck get some kind of undercoating on it? The frame looks so shiny and metallic
probably less than 1000 miles on it, so its still pretty fresh
Can you still get into car garages with this lift cause I work and live in a city where all garages have a 7' clearance?
Has anyone done this lift on 2019 F150 I read that if you put a 4 inch block which the kit comes with you still might say hi in the rear I might try at three I wouldn’t mind it being down a little bit in the back
Awesome.
Love BDS Lift kits.
What size tires did u put on the truck and did they rub at all???
305/70R18 Mickey Thompson Baja ATZ P3 Tires and Method 18x9" Double Standard Wheels with 18mm offset and 5.75" backspacing is what our wheel/tire setup was. We did not experience any rubbing. Give us a call or check with BDS if you go bigger to make sure you wont experience rubbing on your setup. 623 434 5277
What about three spare? Can a full size fit underneath? This is the same set up I'm looking at. Thanks, great vid
sweet! Curious as to how many mpg you loose? I also image that this completely voids the warranty?
bhshakari why people ask that question?? Why so cheap on gas. Gas doesn't matter, if you're always gonna be concern about gas get a bike
*buys pickup truck*
*worries about gas mileage*
Warranty will not be void if you have a dealership that can do installation like mine
wow that is a hell of a hit
hi stage3motorsports. I was wondering if this kit had anything that would get in the way of my magnaflo side exit exhaust. it is the sane side exhaust kit you guys sell
If i added a coilspring on a 6 in susension lift does it add any inches to the 6inch?
The hell with a torque wrench after the fact...that impact was on full send 😆
How’s the ride quality? Is it the same as stock or better?
This is going to be a much better ride than stock.
What size rear block did you put in
Will this work with a zone 4.5” lift kit?
If so will it be level or have a rake?
I’m also doing the zone add a leaf in back of the truck
We've got some good options for that setup! Give us a call 623-434-5277
what did you guys do to black out grill and mirrors? wrap?
At 13:03 mark . . . . . . .Camera man be like " WTF MAN!!!! "
Yes I was haha... but I got the shot!
Where can I see this lift in action?
So only one cross member bracket needs cutting? I don't think i saw him cut more than that one.
Just the drivers side needs to be cut to clearance for the front driveshaft when the drop brackets are installed
Does it add strain to the axle ?
It looks like it's at an angle
The axles are at an angle since the truck is suspended in the air on a lift for the install. The lift kit itself includes the front differential drop brackets to relocate the differential and axles to the correct angles
True that, thanks for the reply
Would I run into any issues running 20X9's on a 4 inch lift? I'm trying to fit 35's with 20's without having to trim anything or lift the truck too high. If not what lift would you recommend?
+jimmy ortiz You can do that on a level with the new f150, the only issue would be the crash bars if your wheels have a low/negative offset. www.f150forum.com has a ton of info you can search on this
I leveled with 35x12.5 on a -12 rim. I had to cut the crash bars to stop the rubbing. Its a street queen in this set up but if you want performance go 4 or 6inch lift and 35s
how about px ranger?6inc
How can I buy fox shocks like that by themselves?
Great DIY...
...Said nobody lolz
Can you tell me what rims and tires? Thank you.
2004-2017 F150 Method 18x9" Double Standard Wheel - www.stage3motorsports.com/MRWMR30489016518-2004-2014-18x9-F150-Method-Double-Standard-Wheel-Black.html
LT305/70R18 Mickey Thompson Baja ATZ P3 - www.stage3motorsports.com/MT-55852-F150-Super-Duty-LT305-70R18-Mickey-Thompson-Baja-ATZ-P3-Radial-Tire.html
Why didn't you run 35x12.5?
What is the total cost of all of this?
Roughly $3,450 Head to the link to learn more! www.stage3motorsports.com/1507F-2015-F150-4WD-BDS-4-Fox-Coilover-Suspension-Lift-Kit.html
Also how much for that 4" lift???
www.stage3motorsports.com/1507F-2015-F150-4WD-BDS-4-Fox-Coilover-Suspension-Lift-Kit.html
What size rims and tire are on this???
They are 17x8.5" with 33' tires Find out more by clicking this link - www.stage3motorsports.com/Stage-3s-2018-F150-5-0L-Budget-Builds-7500-Budget.html
any one know what wheels those are??
Method Double Standard. Check them out here - www.stage3motorsports.com/MRWMR30489016518-2004-2014-18x9-F150-Method-Double-Standard-Wheel-Black.html
truck color?
Brown
@Thamac15 You can find out everything about this build here, www.stage3motorsports.com/Stage3s-2015-F150-5-0L-Desert-Runner-Project-Truck.html
For install cost, call us at 623-434-5277
At 10:56 mark . . . . .that broke a few toe's !!!!!
Please upload videos without music. Thank you.
Great tutorial video but the music needs to go.
You guys didn't paint the metal you just exposed by cutting the drop bracket? Why would I take a new truck here...
We did not paint the metal underneath fortunately in Phoenix we don't have to worry too much about rust.
@@stage3motorsports some cheap rustolem spray paint goes a long way. I was looking for shops to help me set up an overlanding truck, and the truck would spend time on trips more that just in AZ. Its a simple thing to do to show a bit of pride in your work.
The 80s porn music gave me a headache. But great video besides that lol
😂 We agree Jonny we've long done away with the porn music in our videos check out some of our recent installs!
ok fuck that ill just buy a raptor
Why would you make a kit that requires you to cut the frame? This is a terrible kit.
Tracie Lyons this is very common on most kits and for most makes. It's needed to make room for the front dif
It's actually to keep the angles and geometry of the front steering and suspension closer to stock to eliminate binding issues
Alec S cutting the crossmember does nothing for angles, it just allows you to drop the front differential to fix the cv angles. In fact 2wds don't have to cut the crossmember
henceforth fixing the angles that you just stated. and you need to have your tie rods at a certain angle or the stress would cause premature failure of the tie rod ends, also the more extreme angle can damage them during full suspension cycling