X21i projector when switched on the power light go green then back to red, next day it came on but the lamp fan was exhausting very hot air, the lamp would flicker intermittently then the projector shuts down. Power light on steady, if I try a restart, all fans come on for about 3sec then turns off. Lamp timer showed 356 hr. What can cause this problem?
SALUDOS, ME PUEDE SACAR DE DUDAS TENGO UN PROYECTOR EPSON POWER LITE PRESENTER HD, EL BOTÓN DE ENCENDIDO INDICA LUZ NARANJA, LUEGO DECENCENDERLO INDICA LUZ VERDE, PERO PARPADEA 30 SEGUNDO PASA A LUZ NARANJA, NO ENCIENDE LOS VENTILADORES NI LA BOMBILLA,,,,, SERÍA QUE LA LÁMPARA SE HAYA QUEMADO ?
I need min to be fixed I opened it and reseated everything until I found that the wire to the fan underneath its power supply had ripped. I fixed that and still it overheats
I am so sorry you are going through this. I can't give a diagnose of what next unless I was able to see the problem. You could therefore get it looked at by someone close by who can fix the issue.
I have hitachi pj-tx10 projector, when i power off my projector then exhaust fans turn off after less than a minute. Is it ok conditions????? I feel it that projector is very hot even exhaust fans off. Let me know that it is ok situation???????
There are thermal sensors inside the projector that help it in deciding if the fan to turn off or not. You can wait for a few more minutes before you move the projector.
With limited knowledge and no access to the device I will not be of any help since I can't diagnose the device as there could be numerous factors to consider before a solution can be provided. I am extremely sorry for not being of any help. All the best.
I followed the steps but the problem persists.the temp light is still on, i checked all the fans are working...when I turn the projector on, I hear the fans working, for about a minute or less then shut off automatically... Need your help
@@IndipinoyTechthanks for your reply...I cleaned all the fans and the temp light is off now, but the lamp light still on, and shuts off automatically....nothing comes up...
you were very fortunate, it doesn't look like you did anything but disassemble and reassemble, how did a nut get lodged in the fan, I don't understand?
@@IndipinoyTech good point I’m trying to disassemble mine now thanks for posting the video hopefully I find my problem, the temp light is coming on as well and here in barbados nobody works on these projectors …
@@IndipinoyTech hmm I took the projector apart, the fans are working well, however now the lamp light came on and the temp light turned off? Any thoughts other than maybe the temperature getting hot burnt the bulb?
You could try the same fix. Try opening it up and see if you can see if the fan is spinning or not. Usually it is the fan that cools the bulb and if it doesn't cool then there is a problem with the fan. Cheers. Update me if you were able to fix it.
its really kind of you to share your repair experience !!thank you so much!!
I love the horror movie feel 🤣 I definitely would watch more tutorials with a horror vibe
Great video bro. My projector had the same problem. Thanks!!🤘
Thank you so much
I continued watching this video just for the background music
Hahahahaha. Sarcasm 🤣🤣🤣🤣?
X21i projector when switched on the power light go green then back to red, next day it came on but the lamp fan was exhausting very hot air, the lamp would flicker intermittently then the projector shuts down. Power light on steady, if I try a restart, all fans come on for about 3sec then turns off. Lamp timer showed 356 hr. What can cause this problem?
Well done
Thank you
Thank you bro
Welcome
SALUDOS, ME PUEDE SACAR DE DUDAS TENGO UN PROYECTOR EPSON POWER LITE PRESENTER HD, EL BOTÓN DE ENCENDIDO INDICA LUZ NARANJA, LUEGO DECENCENDERLO INDICA LUZ VERDE, PERO PARPADEA 30 SEGUNDO PASA A LUZ NARANJA, NO ENCIENDE LOS VENTILADORES NI LA BOMBILLA,,,,, SERÍA QUE LA LÁMPARA SE HAYA QUEMADO ?
I've had to do this probably every 30 hours of use. I checked the fans but for some reason they don't look dirty.
The trigger could be something else. Could be a capacitor that could be getting overheated and shutting the projector off. Or could be anything else.
I need min to be fixed I opened it and reseated everything until I found that the wire to the fan underneath its power supply had ripped. I fixed that and still it overheats
I am so sorry you are going through this. I can't give a diagnose of what next unless I was able to see the problem. You could therefore get it looked at by someone close by who can fix the issue.
I have hitachi pj-tx10 projector, when i power off my projector then exhaust fans turn off after less than a minute. Is it ok conditions????? I feel it that projector is very hot even exhaust fans off. Let me know that it is ok situation???????
There are thermal sensors inside the projector that help it in deciding if the fan to turn off or not. You can wait for a few more minutes before you move the projector.
EMP-TWD1projector/DVDplayer having problems with green tint...any suggestions? Thank you.
There could be a faulty connector. A service centre could help.
Sanyo PLC-XP21N Projector, i could not repaired and traised the fault. advice pls....
Sorry, can't advise without actually seeing the device.
Hi so do you replace the fan? Or? I didnt see u replace it.
I didn't need to replace the fan. But incase the fan on your projector is not working then you will need to replace it.
Boss saan tayo makabili ng blower EPSON EB S41?
Sir mera hitachi ka projector hai us mein on karne par temp ki light jal rahi hai lamp ignite nahi ho raha
It could be fan or sensor issue
I have an Epson S12+ it works for a few minutes and then turns off. Three red lights appear on without blinking, what problem could that be?
Please take it to a service outlet and they will help.
@@IndipinoyTech I don't have any technical assistance in my town.
With limited knowledge and no access to the device I will not be of any help since I can't diagnose the device as there could be numerous factors to consider before a solution can be provided. I am extremely sorry for not being of any help. All the best.
I followed the steps but the problem persists.the temp light is still on, i checked all the fans are working...when I turn the projector on, I hear the fans working, for about a minute or less then shut off automatically... Need your help
Please check if something else is heating up the device
@@IndipinoyTechthanks for your reply...I cleaned all the fans and the temp light is off now, but the lamp light still on, and shuts off automatically....nothing comes up...
@@mangotea7790 Please check if your lamp has a problem. Maybe the Lamp is faulty
Ça ne marche pas chez moi
Epson projector EB108 lamp how much price sir
I don't know
you were very fortunate, it doesn't look like you did anything but disassemble and reassemble, how did a nut get lodged in the fan, I don't understand?
This was not my projector and so I assume someone fiddled with it before I fixed it.
@@IndipinoyTech good point I’m trying to disassemble mine now thanks for posting the video hopefully I find my problem, the temp light is coming on as well and here in barbados nobody works on these projectors …
@@IndipinoyTech hmm I took the projector apart, the fans are working well, however now the lamp light came on and the temp light turned off? Any thoughts other than maybe the temperature getting hot burnt the bulb?
Ok this is what I found the fans are good however the filter was very dirty and the bulb overheated and burnt out, gonna replace…
Wonderful news. Atleast you found the problem and hoping that sorts it out
My projecter is same problem
Try checking the sensor
Optoma no light problem how to solve
You can begin by checking if the bulb is fused. If it is then you will need to replace it.
Mine is blinking orange but it is cold
Meaning the projector is not turning on.
Hi! I have the same problem the temperature light is blinking, but the fan is working. What may be the problem now? Thanks
The thermostat could be faulty and not able to detect the right temperature.
@@IndipinoyTech Thankyou po for your response. Do I need to replace the sensor?
You might have to check if the sensor is faulty before you replace it.
@@IndipinoyTech good eve po, I would like to ask po if I can replace 13v fan to 12v only?
Usually it is better to replace components with same specifications to minimize damage.
i cant watch any more the music is frightening me! arrrgghhhh
Hahahaha. So sorry for that.
Whats with the creepy music bro.
I was thinking the same. like watching horror movie or resident evil
The music is cool
facing same problem temperature light continues blinking
You could try the same fix. Try opening it up and see if you can see if the fan is spinning or not. Usually it is the fan that cools the bulb and if it doesn't cool then there is a problem with the fan. Cheers. Update me if you were able to fix it.
sure i will let u know
i have Epson 6600
So what?
and bcs of that projector doesnt stat
hi
Hello