Please do not remove the 411 board support or soft serial. We have allot of them and allot of us still use analog video. We still use soft serial for telemetry.
Sure, but there currently isn't any small wing flight controllers on the market for like the Dart250G or the Flying Fish. I have 411 in them now and I don't see many options out there. My big wings, no problem. It's the small ones with the tight fuselages that are hard.
Great release and great video, I think it is a really great release. but I saw few bugs .... perhaps only on my board (Speedybee F405 wing). "save and reboot" button does nothing in the 4 PID pages in 7.0.0 Configurator and flight mode changes (accro manual horizon) are often very long to change on the flight controller when I move the corresponding switch on the transmitter ... and sometimes the mode doesn't change at all (it stays on the last mode selected in the LUA script and also on the telemetry page [TX16S] but I can see the "FM" telemetry information updated many times each second)
I have tried to connect via WiFi to INAV through the ELRS receiver and have been unable to do so. I have read that with Airport you need two independent ELRS systems and I meant using the same Rx I have installed. It seems to connect, but the port closes again after 10s. Is it possible that it is not receiving MSP? I am doing it by AP (access point) with the TCP address in the INAV configurator with 10.0.0.1
hmm ive updated to 7 and cant get motor outputs to work, first when i manually tested motor 1 it spun together with another motor, shortly after nothing also no beeps when turning on. after flashing back to 6.1 works again. (mamba f405 board with 4 seperate esc (hakrc blheli32 dshot1200)
Missed a chunk of the livestream where i asked a question. With this addition of multiple mixers im guessing it now allows you to have different setups that you can flick between during flight? Aka two plane modes, one super safe and the other more agile.
@@lukasztrzcinski3062 Tez o tym myślę✈🤤 ale to dopiero za miesiąc znajdę czas aby go ukończyć dodam ze Paweł Spychalski tez miał takiego Mini Draka 🤤🤤🤤✈✈✈
I tried INAV 7 on my OMnibus F4 V3 after upgrading from INAV 6.. the gps would not work and the magnetometer had issues with I2c but I just had to go lower speed which the configurator did not recommend. The GPS return to normal after going back to INAV 6
Yes you can. But before flashing INAV make a backup of the settings. When you reflash Betaflight you van load the settings you saved and you’re in the air within a few minutes But don’t Try to use all the betaflight settings with INAV, specially not the PIDs an filtering
Please do not remove the 411 board support or soft serial. We have allot of them and allot of us still use analog video. We still use soft serial for telemetry.
it's time to upgrade bro, open source developer don't have time and money to maintain a lot of things
Make your own FC Firmware or just use INAV 6. I don't see a problem, anything that has worked before with your setup will still work.
Sure, but there currently isn't any small wing flight controllers on the market for like the Dart250G or the Flying Fish. I have 411 in them now and I don't see many options out there. My big wings, no problem. It's the small ones with the tight fuselages that are hard.
INAV VTOL for the win!!! :-) Shota for Prime Minister, President etc. LOL
Congrats on the 7th release! That new configurator option to select timer groups rocks!
There were more :)
Is there any plan to introduce "Auto-tuning" for INAV ?
Please tell me where the "Use mid. throttle for ALTHOLD" was removed from the Multirotor Navigation Settings tab ? Or is it enabled by default ?
Great release and great video, I think it is a really great release. but I saw few bugs .... perhaps only on my board (Speedybee F405 wing). "save and reboot" button does nothing in the 4 PID pages in 7.0.0 Configurator and flight mode changes (accro manual horizon) are often very long to change on the flight controller when I move the corresponding switch on the transmitter ... and sometimes the mode doesn't change at all (it stays on the last mode selected in the LUA script and also on the telemetry page [TX16S] but I can see the "FM" telemetry information updated many times each second)
Thenks Bro
I tried out INAV7 and my MATEK optical flow sensor/rangefinder cant be configured. The configuration process locks up.
please create an issue ticket in GitHub repository
@@FPVUniversity Submitted
i am not able to get the output of the receiver signal in the inav, i am using kakute H7 v2 and skydroid T10. pl3ese anybody can help.
I have tried to connect via WiFi to INAV through the ELRS receiver and have been unable to do so. I have read that with Airport you need two independent ELRS systems and I meant using the same Rx I have installed. It seems to connect, but the port closes again after 10s. Is it possible that it is not receiving MSP?
I am doing it by AP (access point) with the TCP address in the INAV configurator with 10.0.0.1
hmm ive updated to 7 and cant get motor outputs to work, first when i manually tested motor 1 it spun together with another motor, shortly after nothing also no beeps when turning on. after flashing back to 6.1 works again. (mamba f405 board with 4 seperate esc (hakrc blheli32 dshot1200)
Missed a chunk of the livestream where i asked a question. With this addition of multiple mixers im guessing it now allows you to have different setups that you can flick between during flight? Aka two plane modes, one super safe and the other more agile.
Dzieki Paweł 🖖
Odpalaj mini draka :P
@@lukasztrzcinski3062 Tez o tym myślę✈🤤 ale to dopiero za miesiąc znajdę czas aby go ukończyć dodam ze Paweł Spychalski tez miał takiego Mini Draka 🤤🤤🤤✈✈✈
VTOL yyds,Goodjob
I tried INAV 7 on my OMnibus F4 V3 after upgrading from INAV 6.. the gps would not work and the magnetometer had issues with I2c but I just had to go lower speed which the configurator did not recommend.
The GPS return to normal after going back to INAV 6
Thenks Bri
Might have missed this. How about dji O3 hd canvas?
Works in BF compatibility mode since INAV 6
I love you Pawel❤
1:03:24 PREACH brother!
With the new mixer mapping capabilities, does yhis mean "bicopter" will now work better with INAV
it will be easier to setup for sure
If I'm running betaflight can I flash inav move my quad over. And if I want to go back to betaflight just reflash betaflight?
Yes you can. But before flashing INAV make a backup of the settings. When you reflash Betaflight you van load the settings you saved and you’re in the air within a few minutes
But don’t
Try to use all the betaflight settings with INAV, specially not the PIDs an filtering
Yes, its a two way trip. If you have backupmyou can go back. I even have a vidoe about the process ruclips.net/video/1hhsqyXeKew/видео.html
Awesome thank you! I wanna play with way points. With inav are you able to put position hold on a switch?
@@Chillin-fpv if you try Inav ... you will stay on it and convert all your quads/plane/wing ... with Inav :)
@f2bcnc74 it's that much better then betaflight huh?
I just learned 6 dang it. Lol
7 is similar, you can do it
I have a vtol project waiting for this. Ardu is just not my cup of tea.
после inava 2.6, все остальное шлак!!!
Летаю на 1.7 и не парюсь
ну я многие пробовал, как оказалась 2.6 самая четкая, и держит позицию офигенно, и унитазинга нет. чем больше всяких функций, тем глючнее)@@MrTuskan