EPA Function on RC6GS V3 / RC4GS V3
HTML-код
- Опубликовано: 7 фев 2025
- How to Assign a Switch to Control EPA on RC6GS V3/ RC4GS V3?
Power RC6GS V3 on. Long press Exit and Enter button at the same time to enter the setting page. -- No.3 EPA EPA is to set different travel amount of a servo on either side from its neutral position.
SW means Switch. You can assign a switch to control EPA. It can be set to NULL, SWA, SWB, SWC, SWD or their lock modes LK-A, B, C, D. If you assign 3 position switch, such as SWB, SWC to control EPA, you can set 3 different end points. If you assign SWA,D, LK-A,D to control EPA, 2 different end points can be switched. If SW is set to NULL, EPA will keep the current values.
The RATE below means the travel amount of the servo, which defaults to 100%. It can be set from 0, the minimum travel amount, to 120%, the maximum. You can adjust EPA of steering, throttle, channel 3, 4, 5, 6, 7
Take SWB, a 3 position switch as an example. Set SW to SWB. Push SWB and the position of SWB is shown in the right corner of the screen. UP-CENTRAL-DOWN.
Push SWB UP first, set the largest travel amount, that is 120%. Please note, you can set different travel amount for the two sides of the channel in EPA. For example, for Steering, set the left side 120%, but the right side 110%. The value can be different for both sides.
Push SWB Central, keep all channels the normal travel amount, that is 100% by default.
Push SWB DOWN, set small travel amount. For steering, set both sides 80%. For throttle, set both sides 80% too.
Setting is done.
Push SWB UP-- the large travel amount
Push SWB CENTRAL- all 100% travel amount
Push SWB-DOWN-- the small travel amount.
What’s the difference of EPA and Dual Rate?
For, EPA, you can set different travel amount of a servo on either side from its neutral position. That means for one channel, you need to set two values.
But for Dual rate, the travel amount of a servo is the same on either side. That means you only need to set one rate for each channel.
For more details of RC6GS V3:
www.radiolink....
Purchase link of RC6GS V3:
www.radiolink....
You can send mails to after_service@radiolink.com.cn if you have any questions during using our products.
I’m glad I found this. I’m trying to set up the transmission servos on a vanquish phoenix and was having a really hard time. It would be awesome if you did a video like this for more of the functions, it’s not easy finding information on what it’s capable of.
Hello, sir. We have made some tutorials on RC6GS V3. You can check these tutorials on our RUclips channel. And here is the detailed manual of RC6GS V3 for your reference: www.radiolink.com/rc6gsv3_manual It introduces all the functions on RC6GS V3. And if there is any question when using RC6GS V3, please feel free to contact us. Our email is:after_service@radiolink.com.cn
You guys seem to be a great company. I'm looking forward to receiving my new v3 and to purchase more of your products. Keep up the great work!
Thank you for your support. If there is any question when using RadioLink products, please feel free to contact us. Our email is: after_service@radiolink.com.cn
Thank you! This is great!
Great to know you like it. We'll make more videos useful to customers.
Thank you
awsome 👏👍
Thank you
Hello, a question please, I have a RC4GS V3, the question is: I turn on the transmitter, when I give full throttle, the display (TH), should move to the right or left? Thanks.
Hi, sit. The display can move to the left or right. Both are okay. If you want to to move to the oppsite direction, you can enter the REV menu to set the channel 2, throttle channel to REV. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
for maximum speed i must set TH to 120 or 100?
Hi, sir. The maximum travel is 120. You can set EPA to 120. Here is the detailed manual of RC6GS V3 for your reference: www.radiolink.com/rc6gsv3_manual If any question please feel free to contact us. Our email is after_service@radiolink.com.cn
how can i reverse the steering as i have added but then steering is around wrong way? thanks
Hi, sir. You can reverse the steering in the basic menu, REVERSE. Here is the detailed manual of RC6GS V3 to show you how to reverse the steering: www.radiolink.com/rc6gsv3_manual If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
Alarm settings What voltage I should the EXT voltage I use 2 battery 4s 8000mah 15.2v?
Hi, sir. The alarm voltage depends on what battery you use. For example, if you are use lipo battery, with full voltage of 4.2V for each cell, we recommend you to set 3.7V for each cell. For example, 2S battery with full 8.4V, you can set alarm voltage as 7.4V. You can also set different alarm voltage as you like. If any question when using RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
Buongiorno ottimo video, desidero sapere il tasto SWD assegnato come L-KD si illumina di rosso quando viene premuto solo per un attimo, è possibile fare che quando il tasto SWD è in ON resta acceso è quando è in OFF si spegne?
Hi, sir. You can adjust the set of switch when setting it. For example, you set LK-D when it is +100 servo value last time. This time, you can set LK-D when it is -100 servo value this time. Then the light condition may be changed. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
Hola en un rc nitro no funciona los eps alguna solución
Hi, sir. Could you please take a video to us to show your problem? It will be helpful for us to know what happened and solve your problem. Our email is: after_service@radiolink.com.cn
Куда Ви серво привод подключаете у меня только отудова подключаю регулятор скорости
Подскажите как подключить регулятор скорости на rema hoby s max 500 рублей кто подскажит
и
Hi, sir, what transmitter and receiver you are using? Please connect the steering servo to channel 1 of the receiver, and ESC to channel 2 of the receiver. You can check the connection from the detailed manual of the transmitter. Here is the detailed manual of RC6GS V3 for your reference. www.radiolink.com/rc6gsv3_manual If any question when using RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
Hi I just bought the rc6gs v3. How can i use the rc6gs transmitter with dumbo rc receiver in my car.? The car currently has a lightcontrol box connected to tye dumbo rc receiver). If i use rc7fg then i loose the lighting functions. So i want to use dumb rc receiver thanks
Hello, sir. RadioLink control system is not open-sourced. RadioLink transmitters are only compatible to RadioLink receivers. So sorry RC6GS V3 transmitter is not compatible with DUMBO RC receivers. We recommend you to change it to R7FG receiver. Connect the light control box to R7FG and then you can also get the lighting function.
@@Radiolink_official @Radiolink hi thanks. How do I coonect the light control box to R7FG? It does not have separate pins for a light control box. Can I split the channel different channel cables? so for example for channel 1, one end goes to the servo and the other goes to the light control box? Thanks
@@Rangeman001 Hello, sir. If there is no pins to be connected to R7FG, sorry it cannot be connected to R7FG.