Explore a wide variety of content in our carefully curated RUclips playlist: • Binge-Worthy Content Find more amazing tips at @TotallyHandyShorts #shorts
То же самое, что заизолировать провода пластилином, замотать куском пакета, а потом наклеить скотч It's the same as insulating wires with plasticine, wrapping it with a piece of plastic bag, and then tape
@@rykersmimi I can understand he want to make cool videos. But when you share a skill you might share it properly so viewers don't learn bad working habits. I think so
@@vincentroux1510 I agree with you on that. I was just throwing my idea of why into the ring, so to speak. I hope anyone that was trying to learn anything from the video realizes that's too much glue & it will definitely leave a big mess and a lot of sanding to do lol
Half a bottle of glue on the dowel, but the fit was so tight most of the glue would have been scraped off the dowel. Water down the PVA, and sand the dowel slightly, and the joint will be a lot stronger as there will be actual glue between the surfaces.
@@JAY-tm7lt it works, but it’s off center, the jig is horrible and there is lots of glue residue. Basically no craftsmenship, hence not a real carpenter.
@@staffkingdray219 the jig was a hack job, the glue he put wasn't properly spread, the jig wasn't centered, the hole blew out a big junk when he drilled it, the dowel was too tight and the glue just got pushed off. Do not recommend this channel
@@jiujitsu1784 это не космофен и даже не ускоритель полимеризации. Это двухкомпонентный суперклей. Компонент А наносится на одну поверхность, В распыляется на другую и при соприкосновении клей полимеризуется.
The FitnessGram™ Pacer Test is a multistage aerobic capacity test that progressively gets more difficult as it continues. The 20 meter pacer test will begin in 30 seconds. Line up at the start.
Everyone's commenting on the glue not going in with the dowel but nobody is bringing up the fact that glues aren't made to be bonded to other glues.....
J'ai jamais compris le concept de mettre de la colle sir la partie mâle et pas sur les deux (trous+ tourillons) du coup la colle ce barres aussitôt que l'on insert les tourillons 🤔🤔. Du coup pas de colle a l'intérieur du trou ? Bref encoller le trou et le tourillons avant montage pour une meilleure tenue 👍
кто же так клеит... Если на ещё мокрый след от катализатора "акфикса" попадёт ПВА он приклеится очень плохо... Если же по человечески приклеить только на ПВА то никаких дополнительных креплений не нужно будет
Шкант в любом случае придал бы прочности, если бы его нормально вклеили. А так согласен, качество работы ужасное. Сейчас любой подросток все свои первые шаги выкладывает в сеть с целью заработать денег, а другие смотрят и думают, что так и надо клеить.
There’s wood tear out where the drill bit exited and oil over glue on the inside joint… would look better without that and also better on camera if done with a little more care….
What is with the RUclipsrs using super glue in between joints? Like, you can't effin wait for glue to dry or something? Wood glue has a better bond than super glue. Just clamp it and wait. Eesh!
اقرأ هذا الدعاء وسوف يحول حياتك إلى جنه هل دقيقه كثيرة على الله؟ ؟ ؟ ؟ لا اله الا الله الحكيم الكريم لا اله الا الله العلي العظيم لا اله الا الله رب السماوات السبع ورب العرش العظيم اللهم إنا نسألك زيادة من الدين وبركة في العمر وصحه من الجسد وسعه في الرزق وتوبه قبل الموت وشهادة عند الموت ومغفرة بعد الموت وعفوا عند الحساب وأمانا من العذاب ونصيبا من الجنه وارزقنا النظر إلى وجهك الكريم اللهم أرحم موتانا وموتا المسلمين اللهم اغفر للمسلمين والمسلمات والمؤمنين والمؤمنات الأحياء منهم والاموات اللهم ارزقنا حسن الخاتمة اللهم ارزقنا الموت ونحن ساجدين لك يا ارحم الراحمين اللهم ثبتنا عند السؤال الملكين اللهم اجعل قبرنا روضة من رياض الجنة ولا تجعله حفرة من النار اللهم إنا نعوذ لك من فتن الدنيا اللهم قوي إيماننا ووحد كلمتنا وانصرنا على اعدائك الدين اللهم شتت شملهم واجعل الدائرة عليهم اللهم انصر إخواننا والمسلمين في كل مكان اللهم أرحم آبائنا وامهاتنا واغفر لهما وتجاوز عن سيئاتهما وادخلهما فسيح جناتك اللهم بارك على سيدنا محمد وعلى آله أجمعين. فأذا نشرت هذا الدعاء فكل من قرأ هذا الدعاء هناك ملك يقول لك مثل هذا الدعاء فلا تستطيع الملائكه من الانتهاء من كتابه حسناتك فقال رجل من السلف لا اله الا الله عدد ما كان وعدد من مايكون الحركات والسكون وبعد مرور سنه قالها مره اخرى فقالت الملائكة انهم لم ينتهو من كتابه حسنات السنه الماضيه فتخيل لو نشرت هذا الدعاء في عشر كروبات ورددها المئات من خلالك فكم حسنه لك .دقيقه!!! صح انو الرسالة طويلة ورح تقول/ي كيف بقراها كلها بس جرب مره نفسك واقرأها والله راح ترتاح قبل ما تفتح الرسالة اطلب ما تتمناه اقر الرساله کامله قال صلى الله عليه وسلم : "من قرأ هذا الدعاء وأخبر الناس به فرج الله همه ارسله لوجه الله إذا ماقدرت ترسلها فأعرف ان الله غني . عنك والله العظيم أنا بنفسي ما صدقت و کنت آظن آنها اشاعة ولو لم تكن كلمة لا اله الا الله ! ما ارسلتها يقال أن هذه الرساله و صلت الى عميد بحري فوزعها على 12 شخص فحصل على ترقية خلال 11 يوم وصلت هذه الرسالة الى تاجر فأهملها فخسر كل ثروته خلال 12 يوم ... وصلت هذه الرسالة الى عامل فوزعها ف حل الله له كل مشاكله خلال 12 يوم ووصلت هذه الرسالة الى طالب على ابواب الامتحان فخاف الا ينجده الله فوزعها فنجح ارجو انی كنت من الظالمين ارسلها وستسمع خبر حلو الليله باذن الله قلت اجرب واشوف ايه قصه هذه الرساله صدقني سوف تأتيك لحظة تتمنى تكون عايش وترسلها و الي يبي يعرف كيف ينسخها انسخ رابط الفيديو وحطو في كروم بعدين ادخل التعليقات وانسخو. جرب بس ارسلها و اصبر شوي ان الله مع الصابرين جرب بس والله راح تج نجي لحظه تتمنى تكون عايش وترسلها اللهم اشفي بصري وكل مرضى المسلمينبسم الله الرحمن الرحيم بإذن الله تعالى يا الله يا كريم يا أول يا آخر يا مجیب یا فارج الهم يا كاشف الغم فرج همي و يسر أمري و أرحم ضعفي و قلة حيلتي و أرزقني من حيث لا أحتسب یا رب العالمين منك ان توزعها على الاقل على 12 فرد لمجرد انها تحتوى على كلمة لا اله الا الله محمد رسول الله و أسماء الله الحسنىدعاء سيدنا يونس عليه السلام لا اله الا انت سبحانك شكرا اذا كملتو القراءة مو انا كتبتها
जिस दिन से हृदय में इस्ट का आविर्भाव होता है,उसी दिन से निर्देश देने लगता है; किंतु प्रारंभ में साधक समझ नहीं पाता| पराकाष्ठाकाल में ही योगी उसकी आंतरिक कार्य-प्रणाली को पूर्णत: समझ पाता है| यही समझ विज्ञान है| (यथार्थ गीता 6/8)
none of that glue went in the hole
My first thought.
That's what she said 😏
It dried up or already sticked already.. it is short.
It did, but dry wood is very absorptive.
@@sleepybesleeping she was you mom
Do you think he realizes absolutely no glue went into that hole. ???
BS joint right there
That's what she said
that white-ish creamy glue
Do us a favour and show us how you made that jig, a jig like that would come in handy a lot more than the joint itself.
agree.
👍
Yes, that would be real useful...👍
Looks like a square block with a hole drilled through then an angled C notch cut on the bottom, maybe with a hole saw bit.
Forstner bit the size of the rod
Too much waste of glue 😅
То же самое, что заизолировать провода пластилином, замотать куском пакета, а потом наклеить скотч
It's the same as insulating wires with plasticine, wrapping it with a piece of plastic bag, and then tape
What is with you adding superglue the wood joints? Stop it, get some help.
Woodworking rule number one put the glue into the mortise not on thé tenon...
When tout teach something learn about it before please
I don’t even do woodwork and that seemed obvious to me. The way he did it 99% of the glue came off😂😂
I'm thinking it's done like that for video effect. I know some other creators will use more of something if it looks good on camera.
@@rykersmimi I can understand he want to make cool videos. But when you share a skill you might share it properly so viewers don't learn bad working habits. I think so
@@vincentroux1510 I agree with you on that. I was just throwing my idea of why into the ring, so to speak. I hope anyone that was trying to learn anything from the video realizes that's too much glue & it will definitely leave a big mess and a lot of sanding to do lol
One of the only things I could point out for future is try to align the new diles wood grain to try and match up
Half a bottle of glue on the dowel, but the fit was so tight most of the glue would have been scraped off the dowel. Water down the PVA, and sand the dowel slightly, and the joint will be a lot stronger as there will be actual glue between the surfaces.
When you have a RUclips channel, and try to act like you’re a carpenter
Why wouldn't this work?
@@JAY-tm7lt it works, but it’s off center, the jig is horrible and there is lots of glue residue. Basically no craftsmenship, hence not a real carpenter.
Why drill through and make two holes?
Why not use similar wood for dowel?
And a skilled welder
That was gorgeous 😍
What was the last thing you added as a spray please??.
Activator
@@laargboolag9147 thanks
Np
That hurt my eyes and made me lose brain cells
Why? What did he do wrong
@@staffkingdray219 the jig was a hack job, the glue he put wasn't properly spread, the jig wasn't centered, the hole blew out a big junk when he drilled it, the dowel was too tight and the glue just got pushed off.
Do not recommend this channel
Bro just made an angle 💀
@@NimmyJam "made an angle"
Kinda sorta.....😄😄😄
That wasn't hot dog with mayonnaise and ketchup!!!
I remember my first joint.... carpentry joint ofcourse. 😆
Any joint is a carpentry joint if it's inside a shop.
Не пойдет,надо еще саморезом скрутить🤣
Да, верно👍
“If you can’t get the joint to fit, just fill it up with glue and 💩.”
That’s the sign of a cowboy…..Yeeeeehaw pardner!!!
К
Мне сначала показалось, что это сосиски.
At first I thought it was sausages.
Initially I thought they were sausages for some reason
Haha 😂
What were all those different glues you used? I've never seen Crazy Glue used on wood.
Why you use 3 different glue to joint wood?
Отверстие для шкантов надо внутри промазывать клеем
И не сверлить насквозь
Да, тоже подумал.
Ну и финишную надо чище делать
интересно а после Тайт бонда он чем там набрызгивает? Типа космофен и что-то в балончике?
@@jiujitsu1784 это компонент "активатор". Ускоритель полимеризации суперклея
@@jiujitsu1784 это не космофен и даже не ускоритель полимеризации. Это двухкомпонентный суперклей. Компонент А наносится на одну поверхность, В распыляется на другую и при соприкосновении клей полимеризуется.
Why did he spray liquid on the wood before he glued it? Wet wood is less absorptive.
The FitnessGram™ Pacer Test is a multistage aerobic capacity test that progressively gets more difficult as it continues. The 20 meter pacer test will begin in 30 seconds. Line up at the start.
Как же много лишнего клея выходит, больно на это смотреть...
Good job👌👍
Everyone's commenting on the glue not going in with the dowel but nobody is bringing up the fact that glues aren't made to be bonded to other glues.....
Don't know how but these two parts of wood at the beginning looked like legs for me at first
What is this for??? I’m a carpenter, this is my job! I can tell you that this is overkill!
What's the right way to do it?
Uhhh so am I and I’ll tell you that this is the only good short there’s ever been
Сначало подумал колбаса ,майонез капнул,кетчуп)) потом когда он клеил ,думаю- во дурень!))))
Ayan.modassir
King पर
Ваш комментарий улыбнул))
Nice trick👍
What are those 2 glues? Wood glue and cyanoacrylate?
Might have looked better if you’d used matching wood for the dowel and removed ALL of the glue !
Nah, the lighter color makes it pop a little
Яйухан?
Love it 👍
How many different types of epoxy do you need?
Not a good glue joint. The superglue accelerator trick actually weakens the joint.
Why, just whyyyyyyyyy!!!!!!!!!
Didn’t know liquid cheese works like an adhesive
So relaxing
J'ai jamais compris le concept de mettre de la colle sir la partie mâle et pas sur les deux (trous+ tourillons) du coup la colle ce barres aussitôt que l'on insert les tourillons 🤔🤔. Du coup pas de colle a l'intérieur du trou ? Bref encoller le trou et le tourillons avant montage pour une meilleure tenue 👍
кто же так клеит... Если на ещё мокрый след от катализатора "акфикса" попадёт ПВА он приклеится очень плохо... Если же по человечески приклеить только на ПВА то никаких дополнительных креплений не нужно будет
Шкант в любом случае придал бы прочности, если бы его нормально вклеили. А так согласен, качество работы ужасное. Сейчас любой подросток все свои первые шаги выкладывает в сеть с целью заработать денег, а другие смотрят и думают, что так и надо клеить.
What was the point of the CA glue? The wood glue just squeezed out over it as you pushed the pieces together.
There’s wood tear out where the drill bit exited and oil over glue on the inside joint… would look better without that and also better on camera if done with a little more care….
What do you use that for?
Glue IN THE hole...
Точно!! в дырочку!!
Great 👍
There is no reason to mix glue types like that.
So this is why I banged around a picture frame for 10 hours
I don’t think you used enough glue. Better add more, you know, just in case the first two bottles weren’t enough. 🤦♂️
Yo una vez fabriqué una jaula de gallo de madera, era bastante incomoda pero muy gratificante.
Tezene 1
You got enough glue there boss?
And maybe the other angle of the frame would have showed it was already completely sideways
Such things need to be taught in school
School does it better than him
Get him a way from wood.
They teach skills in school. This is nonsense
What name of glue and spray ?
Probably 99.99% of the people who liked this don't even know a thing about woodworking.
What is with the RUclipsrs using super glue in between joints? Like, you can't effin wait for glue to dry or something? Wood glue has a better bond than super glue. Just clamp it and wait. Eesh!
If you ever need to sweep around corners.
not only me loving the craft and the jazz hip hop in the background☮️
Клей в в отверстие не попал.
There has to be a better way apply those glue.
Never saw towards your hands kids. NEVER!
strongest joint ever
Laajawab hai
Still I’m irritated!!!! You did this for the views! This content blows!!!
Such a beautiful joint and u ruin it by drilling a hole in it
I like the jig.
But why did you insert something in that joint making it weak wasting glue and that piece that you inserted
What spray is this?
2p10 adhesive+activator
Good it just stocked the table
Beautiful
Satisfying
Klej trzyma tam gdzie go nie ma.
With your glue mix sprinkle some bakinsoda
The glue must be in the hole!!!! Bad carpenter
What are the chemical you applied
2p10+activator. Don't listen to this guys advice though. Go read a book by someone who actually knows what they're doing.
Do you work in Nokia factory?
There is a new invention made called screws
Because it is painted
Thank you
Title of the music please?
Nice
A spline would probably be better but that's just my opinion maaan
Отвратительное качество работы. Отверстие криво просверлил, шкант загнал по сути без клея и в конце вообще непрошлифовал. С натяжкой тянет на 3.
Клей огонь, но стоит, как крыло от самолета.
Потому что его везут из Америки. Есть такие же качественные, а в чем то даже лучше произведённые на нашем континенте
Дружище , что за музыка играет? Кайф и видео и музыка 👍
Шип нужно из такого же дерева делать, а то колхозно смотрится
This is due to overthinking , over done. It's simple and easy to joint, you don't need to do this n that so many steps with so much of glue etc
各种胶水粘合剂……就为了让两个木头永远连在一起,这智慧真是“简单粗暴”
Amd that's how you waste a good wood.
The dile needs to be aligned
اقرأ هذا الدعاء وسوف يحول حياتك إلى جنه هل دقيقه كثيرة على الله؟ ؟ ؟ ؟ لا اله الا الله الحكيم الكريم لا اله الا الله العلي العظيم لا اله الا الله رب السماوات السبع ورب العرش العظيم اللهم إنا نسألك زيادة من الدين وبركة في العمر وصحه من الجسد وسعه في الرزق وتوبه قبل الموت وشهادة عند الموت ومغفرة بعد الموت وعفوا عند الحساب وأمانا من العذاب ونصيبا من الجنه وارزقنا النظر إلى وجهك الكريم اللهم أرحم موتانا وموتا المسلمين اللهم اغفر للمسلمين والمسلمات والمؤمنين والمؤمنات الأحياء منهم والاموات اللهم ارزقنا حسن الخاتمة اللهم ارزقنا الموت ونحن ساجدين لك يا ارحم الراحمين اللهم ثبتنا عند السؤال الملكين اللهم اجعل قبرنا روضة من رياض الجنة ولا تجعله حفرة من النار اللهم إنا نعوذ لك من فتن الدنيا اللهم قوي إيماننا ووحد كلمتنا وانصرنا على اعدائك الدين اللهم شتت شملهم واجعل الدائرة عليهم اللهم انصر إخواننا والمسلمين في كل مكان اللهم أرحم آبائنا وامهاتنا واغفر لهما وتجاوز عن سيئاتهما وادخلهما فسيح جناتك اللهم بارك على سيدنا محمد وعلى آله أجمعين. فأذا نشرت هذا الدعاء فكل من قرأ هذا الدعاء هناك ملك يقول لك مثل هذا الدعاء فلا تستطيع الملائكه من الانتهاء من كتابه حسناتك فقال رجل من السلف لا اله الا الله عدد ما كان وعدد من مايكون الحركات والسكون وبعد مرور سنه قالها مره اخرى فقالت الملائكة انهم لم ينتهو من كتابه حسنات السنه الماضيه فتخيل لو نشرت هذا الدعاء في عشر كروبات ورددها المئات من خلالك فكم حسنه لك .دقيقه!!! صح انو الرسالة طويلة ورح تقول/ي كيف بقراها كلها بس جرب مره نفسك واقرأها والله راح ترتاح قبل ما تفتح الرسالة اطلب ما تتمناه اقر الرساله کامله قال صلى الله عليه وسلم : "من قرأ هذا الدعاء وأخبر الناس به فرج الله همه ارسله لوجه الله إذا ماقدرت ترسلها فأعرف ان الله غني . عنك والله العظيم أنا بنفسي ما صدقت و کنت آظن آنها اشاعة ولو لم تكن كلمة لا اله الا الله ! ما ارسلتها يقال أن هذه الرساله و صلت الى عميد بحري فوزعها على 12 شخص فحصل على ترقية خلال 11 يوم وصلت هذه الرسالة الى تاجر فأهملها فخسر كل ثروته خلال 12 يوم ... وصلت هذه الرسالة الى عامل فوزعها ف حل الله له كل مشاكله خلال 12 يوم ووصلت هذه الرسالة الى طالب على ابواب الامتحان فخاف الا ينجده الله فوزعها فنجح ارجو انی كنت من الظالمين ارسلها وستسمع خبر حلو الليله باذن الله قلت اجرب واشوف ايه قصه هذه الرساله صدقني سوف تأتيك لحظة تتمنى تكون عايش وترسلها و الي يبي يعرف كيف ينسخها انسخ رابط الفيديو وحطو في كروم بعدين ادخل التعليقات وانسخو. جرب بس ارسلها و اصبر شوي ان الله مع الصابرين جرب بس والله راح تج نجي لحظه تتمنى تكون عايش وترسلها اللهم اشفي بصري وكل مرضى المسلمينبسم الله الرحمن الرحيم بإذن الله تعالى يا الله يا كريم يا أول يا آخر يا مجیب یا فارج الهم يا كاشف الغم فرج همي و يسر أمري و أرحم ضعفي و قلة حيلتي و أرزقني من حيث لا أحتسب یا رب العالمين منك ان توزعها على الاقل على 12 فرد لمجرد انها تحتوى على كلمة لا اله الا الله محمد رسول الله و أسماء الله الحسنىدعاء سيدنا يونس عليه السلام لا اله الا انت سبحانك شكرا اذا كملتو القراءة مو انا كتبتها
Вчём прикол то? Как правильно углы сводить.
Un tarugo del mismo madero , quedaría del mismo color
Только у меня сложилось мнение, что мастер рукожоп?
Perfect
Next video... Pulls truck with it .
जिस दिन से हृदय में इस्ट का आविर्भाव होता है,उसी दिन से निर्देश देने लगता है; किंतु प्रारंभ में साधक समझ नहीं पाता| पराकाष्ठाकाल में ही योगी उसकी आंतरिक कार्य-प्रणाली को पूर्णत: समझ पाता है| यही समझ विज्ञान है|
(यथार्थ गीता 6/8)
Я не особо разбираюсь в этом,но мне кажется,что он таким приёмом лишь ослабил соединение
Не ослабил, но эстетически испортил.
Шкант с глухими посадками намного красивее выглядело бы.
What song is this???
Clean it with am brush before oiling. Still full of glue on the surface🤷♂️