OK Ben a couple of thoughts on what you are doing now. You should have done the head when the boat was on the dry, it would have save you a lot of headaches, but I at least you should have made sure and precut all the plywood for the build and defenettly you should have done all the through hull on the dry. also 1 layer of fiberglass it's not enough, you should do 2 or better 3 layers. Also putting cement like that is going to come back and bit you in the ass, if you need to remove the balast and bet you will have to do it sooner or latter, is going to be a messy thing of a job to do. Just thinking out loud. The best of lucks
Thanks! You probably should at least a second layer of fiberglass on your floor, especially if it’s gonna be a wet head. It helps to prevent water finding pinholes through the current layer of fiberglass.
My two cent comment, same as many said : putting cement in contact with wood is the primary source of rot. You can't say you were not warned! Have a good week nevertheless, and don't be affraid to slow the pace. You will and up with better results! Greetings from French Riviera..
Pretty sure the mortar mix, thick as Ben is mixing it, will not penetrate the ballast rock through to the hull and will hopefully just lock the ballast in place.
I know you were both going crazy to leave the boatyard. However having a working head on board probably should have been on the must do list before you left.
Hello Ben, A trick I learned from a master builder is to place some wet mortar or cement in a plastic (trash) bag, then put the shower floor down on top so it squishes to fill the space and support the fiberglass floor. Then it can be removed later if you ever need to do that, and the floor will not flex too much making micro cracks over the years. Keep up the good work!
Concrete likes to draw in moisture , I would worry that it might accelerate the wood planks rotting underneath the concrete. Hopefully it doesn’t in this case, but please keep an eye on it, perhaps wait to put the flooring in till it dries and make sure it’s not wicking water into the boat. Good luck with it, the rest is looking great!
a lot of wood boats are ballasted with concrete, the alkaline character of the cement prevents rotting. should be working but of course should make sure its dried out.
@@schuttrostig5729 thanks for your comment, my experience comes with a construction background and it’s why we use treated lumber against the slab when building. Someone else had said when they use concrete for boats they add something to it, so hopefully they don’t have any issues!
I feel like pouring concrete on and around your wood is the biggest mistake you have made in your rebuild, by far. This will be guaranteed to be the first area to rot out. I urge you to reconsider, chisel that out and take a different approach.
tough one, not sure of effect on timber, but that sods law says, if you can't get to it or see it, you'll have future issues there - and when its comes to that future issue to have a look and make sure, adding cement will of course be another hurdle to overcome - i might have lined the underside with plastic sheet, concreted, but still be an issue to get out the way if needed my rule is with anything, there is no issue with water getting into anything, as long as it can drain or evaporate
Everyone tends to have an opinion. Don’t change a thing you both are doing an amazing job. I love seeing the boat on the water and the 2 pups make the channel a 1000% better. 🙏🏻😎 #boatlife
@04:16 It's always tricky to epoxy wood in the sun. The heat of the sun can make the air in the wood expand and form bubbles. @04:46 As you can see here, all the white spots...
MP & Ben your skills working in all the different materials has gotten so good . Ben your determination to finish a functioning Head is critical and essential . Anyone who's tried using a bucket in a bouncy & rocking boat knows things can get out of hand pretty quick . Go Team Yaba !
Didn't see much of MP, hope all is well! Great episode, as usual, but I sensed a wee bit of angst which is to be expected since life doesn't just toss us roses every day. Be strong, loving, and keep on giving Yaba the care she demands. All the best to the four legged crew---talk about love!
What a beautiful mast! Ben, you’re a maniac. Working hard! You’ve both worked so hard on Yaba. (Please keep fishing.) (FANTASTIC looking smoothie, MP! 😉😁)
Hi Ben & MP, Great to see work continuing on the water, YABA looks so nice resting at anchor. So much has changed , Perhaps one of the most satisfying changes is to see how much the dog's have become at home on board YABA. To see them on the floatie with Ben ,having fun is testament to how far they have come , from life in the boat yard to members of the crew , relaxing at play on the water , My Dad always said "a dog's life is the best life ,if they have an owner /master who really loves them" , Your dog's look so happy living with you guys, at sea ,aboard YABA. Nice one guys . Great vid ,very cool indeed. Respect.....!
Over the years of watching you remake Yaba I occasionally commented that the skills you were and would continue to learn will be a real blessing once underway. I certainly see all that hands-on education in the work done - and the head's really beginning to look great, Cheers from Vancouver BC Canada
Don't worry keep the faith, one day at a time. On another note I'm jealous because I can't float on my back and you made it look so easy. Keep up the good work Yaba-Daba-Do. 😊🎉
I seem to remember, when I was looking at doing something similar in a steel hulled boat that if you don’t put special chemicals in your cement, it will retain water, so if any gets through your floor, or any condensation that occurs it will soak in to the cement and could damage the hull. Maybe different in a wooden boat.
Slow and steady is the way to go. This old fella has never owned a big boat or lived on a boat only boat he's ever stayed on was a cruise ship. It's been fun watching you progress in your abilities. You have taken on a challenge to live your dream where a lot of others would have stopped at rotten wood on your boat in the beginning. Pretty sure you have your contacts that have done this for years and they are giving you some good tips. Love catching up on Sunday mornings.
Lot's of progress, lots of variety in this episode. Ben and MP, and their furry crew really make this series, but the undisputed star is the stunningly beautiful Yaba!
Ben, Building boats in College while earning My Bachelor of Science in Marine Engineering & Technology, we never used concrete in the hulls. Although there were guys actually building their hulls out of concrete. Hey, it’s your boat Ben, You Do You My Brother. I pray you all stay safe in the name of Jesus, Amen 🙏
Ben, the work on the bathroom floor is nice, but you also have to compensate on the other side of the boat, otherwise the added weight of the concrete and stones skid the boat.
18:42 why not use what they call Crete board and just lay over that so you don’t have to bust that up at every problem underneath there. Or is there not Crete board there where you’re at? Crete board is concrete plywood type and you lay it down and it’s concrete. Not trying to say that you don’t know what you’re doing. In my opinion, I wouldn’t use Crete board but I don’t know the situation. I’m not on the yacht. But hey, love the new boat. Awesome.
Ben you could have a small wind turbine to help recharge your batteries when it is overcast this way you will save fuel and not put unwanted hours on your engine, the concrete was a good idea so long as it hasn’t gone through to the hull , the old girl is looking absolutely beautiful, keep the dream alive best wishes from Tasmania Australia 🇦🇺
There are many comments I can make about the bathroom, but it's important that he makes his own decisions and do it as he wants. Mistakes are lessons for the future. I believe it will make him a better sail boat owner and sailor. He's determined and that's a good thing.
Are you not going to reinstall your upper hand rails ? Also way haven't you found a birth so you can have a more stable place to work on your boat. While you tried to catch a fish, MP did something I thought I'd never see happen.... She used your own power to make food, and just seeing that made me feel so good after all this time. What a blessing. Don't go too crazy adding weight to one side without adding it the other side, you don't want your boat to lean. LOL.
... love that Yaba' is on the water ... love that you're living your dream ... love that you're getting the head completed, but love even more how the yard dogs have become cruising canines so nicely ... just one question ... who's the boss, you guys or the pups? ...
Ben & MP your intuitions on performing the requisites of accomplishing all of the final tasks on Yaba using the diverse materials is uncanny & I am inspired by your determination to install a complete first class head. Having to shit in a bucket and then having to handle it, becomes as disgusting as it is also disheartening.
Ben illustrated why the plumbing and holes cut into the hull are done before you splash the boat. Not sure about the concrete as it will make it difficult to access that area of the hull as it would be hard to swing a pickaxe in the space of the head and even more difficult to find a jackhammer while at sea to break apart the concrete. But the odds are slim there will be any issues with the area as Ben has it sealed well.
Hey Y’all. Mark from Atlanta GA. Love the content. Been following since Odd Life suggested you did. Anyway last 5 videos or so you have spots on your lens. Definitely noticeable. I look forward to every Sunday!!
Good work Ben. A word of caution, you might want to consider wearing a mask while sanding the mast. That sander’s dust bag isn’t 100% effective. As a 70 year old carpenter believe me.
Yes, this is true there is also far better products than varnish I use a decking oil Sikkens better results and lasts longer if you want to go cruising get away from varnish or you will be always redoing it looks great, but a lot of work and you could use it on the capping as well as all the outside timber surfaces love watching your videos been watching from the beginning look forward to the next one.
It really is important to be able to access every part of your hull. If you were to hit something in the water or otherwise, damage the wooden planking, you know cannot get at that area plus the issue of the concrete, attracting water and causing rot. REALLY BAD IDEA.!
As far as the concrete goes ... God help you if you ever need to access that section of the hull -- the loose stone could be moved for emergency repairs, while this is fixed in place. I know that you will not have access as you pointed out, but if you ever hit anything and damage the hull or frames think of all the extra work jack hammering all of that out even on the hard at a yard. I think adding some bags of lead shot would have been the safer solution -- it would have conformed to the gaps, and could still be removed (also denser that concrete so less needed). On another note: during the drone footage early in video the rear mast appeared to have a starboard lean, you may want to check the tension on the stays on both sides port might be loose or starboard too tight -- check the footage. Glad to see you making progress with the boat on the water!! Cheers!
I am confused…is there no drain? Is this a shower toilet combo and if so, wouldn’t there be a drain before concrete? I am sure you have a plan…I just don’t see it yet ❤❤
Despite others mentioning it, a moisture barrier should always be used between wood and concrete. Moisture will wick out of the concrete forever and cause the wood to rot. Otherwise, great job.
Is there a below decks exit from that forward compartment? It looks like if the hatch got blown shut while you're down there, that hasp could swing shut and lock you in...Just reversing it could fix that...And, wouldn't a 'camping' toilet be a bit better? (a seat on a 5 gallon pail, with plastic bag liners)
It's so good to see you in the water! Wow,k what a journey! I am curious about the tender? I saw it when you brought it into the yard. Is it fiberglass? over an inflatable? I don't remember an episode on the actual tender?
Good for you guys!! At least someone is happy!!😮 I just have the bathtub!! And... And? I have to economize on the water!😮 This isn't easy!! 😭 Now!!! I'm going to call the Happiness Police!! Yes, on you!!! Just kidding, guys!! All the best!! Tudo de Bom para Vocês!!
Made worse by fibre-glassing in the freshly poured concrete. It typically takes 28 days to dry for every 25mm of slab thickness. The only way out for the moisture now is into the hull timber.
I found this info online after watching your your video. Not sure if it applies to your situation. Can wood be in contact with concrete? Moisture absorbed by the concrete or masonry may cause the wood to rot - unless that 1/2 inch of space is maintained. Typically, though, the space is closed up for aesthetic reasons, so decay-resistant lumber is used.
My thoughts too, but as I tend to make too many critical comments, I bit my tongue. That freshly poured concrete is now encapsulated, complete with freshwater moisture. I don't like the idea of pouring concrete in the bilge either. It's not an uncommon practice apparently, but counter-intuitive for me. LOTS of work with a pneumatic hammer will now be required to access the hull. I've watched Gemma and Simon removing bags of ballast from Sarinda's bilge, and that was hard enough work already, without having to break up solid concrete. Edit: I may be mistaken about the fresh concrete being "encapsulated". Ben may have ensured that he left some airflow space between the new head sole and the concrete? Here's hoping!
There seems to be a lot of negative comments about the concrete being used but I’m pretty sure you only put it against painted wood so it should be fine, I can’t see your plan for the bathroom yet I can only imagine that it’s some sort of wet room, but I haven’t seen any floor drain going in so I’m unsure, if it’s just a toilet and wash hand basin you have gone way over the top with the fibreglass, I would say only do one project at a time you will burn out doing so much constantly. Good luck 😊❤
Paint only slows down the absorption. All paints and coatings are permeable to water, just to varying degrees. In this case, the freshly poured concrete was fiber-glassed in before it was cured, so a lot of moisture will be looking for a way out. About the fiber-glass, I think 1 layer would be the bare minimum for a "dry" head, as water would still be splashed around to some degree. For a wet head a minimum of 2 layers, ideally 3 or more.
![BLACK BAG - Official Trailer [HD] - Only in Theaters March 14](http://i.ytimg.com/vi/Du0Xp8WX_7I/mqdefault.jpg)
OK Ben a couple of thoughts on what you are doing now. You should have done the head when the boat was on the dry, it would have save you a lot of headaches, but I at least you should have made sure and precut all the plywood for the build and defenettly you should have done all the through hull on the dry. also 1 layer of fiberglass it's not enough, you should do 2 or better 3 layers.
Also putting cement like that is going to come back and bit you in the ass, if you need to remove the balast and bet you will have to do it sooner or latter, is going to be a messy thing of a job to do.
Just thinking out loud.
The best of lucks
Thanks!
You probably should at least a second layer of fiberglass on your floor, especially if it’s gonna be a wet head. It helps to prevent water finding pinholes through the current layer of fiberglass.
Couldnt ofsaid it better
My two cent comment, same as many said : putting cement in contact with wood is the primary source of rot. You can't say you were not warned! Have a good week nevertheless, and don't be affraid to slow the pace. You will and up with better results! Greetings from French Riviera..
Pretty sure the mortar mix, thick as Ben is mixing it, will not penetrate the ballast rock through to the hull and will hopefully just lock the ballast in place.
Really , your in the french riviera I'm farther along but most french houses (older) have beams in cement walls and stand for decades !
@@photize "Stand for 100's of years" build with cement who was invented ~1850
404
I know you were both going crazy to leave the boatyard. However having a working head on board probably should have been on the must do list before you left.
All they need is to cut a hole in the swimboard and place two cute feet from non-slippery material beside it... 🐟🐬🐋
Hello Ben, A trick I learned from a master builder is to place some wet mortar or cement in a plastic (trash) bag, then put the shower floor down on top so it squishes to fill the space and support the fiberglass floor. Then it can be removed later if you ever need to do that, and the floor will not flex too much making micro cracks over the years. Keep up the good work!
Hi Ben, just a quick question did you or are you going to sand and varnish the marsts
Oh thank God you started on the unfinished mast. Been driving me nuts. Lol
Concrete likes to draw in moisture , I would worry that it might accelerate the wood planks rotting underneath the concrete. Hopefully it doesn’t in this case, but please keep an eye on it, perhaps wait to put the flooring in till it dries and make sure it’s not wicking water into the boat. Good luck with it, the rest is looking great!
a lot of wood boats are ballasted with concrete, the alkaline character of the cement prevents rotting. should be working but of course should make sure its dried out.
@@schuttrostig5729 thanks for your comment, my experience comes with a construction background and it’s why we use treated lumber against the slab when building. Someone else had said when they use concrete for boats they add something to it, so hopefully they don’t have any issues!
I feel like pouring concrete on and around your wood is the biggest mistake you have made in your rebuild, by far. This will be guaranteed to be the first area to rot out.
I urge you to reconsider, chisel that out and take a different approach.
They are using it more as a mortar instead of a more traditional concrete pour.
tough one, not sure of effect on timber, but that sods law says, if you can't get to it or see it, you'll have future issues there - and when its comes to that future issue to have a look and make sure, adding cement will of course be another hurdle to overcome - i might have lined the underside with plastic sheet, concreted, but still be an issue to get out the way if needed
my rule is with anything, there is no issue with water getting into anything, as long as it can drain or evaporate
Everyone tends to have an opinion. Don’t change a thing you both are doing an amazing job. I love seeing the boat on the water and the 2 pups make the channel a 1000% better. 🙏🏻😎 #boatlife
Yabá is a beautiful boat. You are doing a great job bringing her back to life. Cant wait to see those masts sanded and the sails up.
@04:16 It's always tricky to epoxy wood in the sun. The heat of the sun can make the air in the wood expand and form bubbles.
@04:46 As you can see here, all the white spots...
Heard the same , do it at start of night
I have watch this from the start. This couple have a buetiful relationship with each other.
MP & Ben your skills working in all the different materials has gotten so good . Ben your determination to finish a functioning Head is critical and essential . Anyone who's tried using a bucket in a bouncy & rocking boat knows things can get out of hand pretty quick . Go Team Yaba !
Didn't see much of MP, hope all is well! Great episode, as usual, but I sensed a wee bit of angst which is to be expected since life doesn't just toss us roses every day. Be strong, loving, and keep on giving Yaba the care she demands. All the best to the four legged crew---talk about love!
She is busy filming Ben!!
@@judywebb8358 No kidding? Duhhhh!
You can almost see that your two stray dogs realize how lucky they are to have found you two
🥰🥰🥰
What a beautiful mast! Ben, you’re a maniac. Working hard! You’ve both worked so hard on Yaba. (Please keep fishing.) (FANTASTIC looking smoothie, MP! 😉😁)
Ben you're a hero working so hard!
Hi Ben & MP,
Great to see work continuing on the water, YABA looks so nice resting at anchor.
So much has changed ,
Perhaps one of the most satisfying changes is to see how much the dog's have become at home on board YABA.
To see them on the floatie with Ben ,having fun is testament to how far they have come , from life in the boat yard to members of the crew ,
relaxing at play on the water ,
My Dad always said "a dog's life is the best life ,if they have an owner /master who really loves them" ,
Your dog's look so happy living with you guys, at sea ,aboard YABA.
Nice one guys .
Great vid ,very cool indeed.
Respect.....!
You guys are so fortunate to have those dogs! What a pair they are.
🥰🥰🥰
Over the years of watching you remake Yaba I occasionally commented that the skills you were and would continue to learn will be a real blessing once underway.
I certainly see all that hands-on education in the work done - and the head's really beginning to look great,
Cheers from Vancouver BC Canada
What an elegant vessel Yaba is! You guys are so lucky.
Don't worry keep the faith, one day at a time. On another note I'm jealous because I can't float on my back and you made it look so easy. Keep up the good work Yaba-Daba-Do. 😊🎉
Awesome job can wait to see you sailing around the world to the north pole to the South Pole and everywhere in between
The boat is a inshore sailing vessels would require many more improvements before insurance would allow go offshore
Things take time, when your run outa time, you go over time. Nice goin Ben. Thanks m8s, stay vertical, cept when your on the pot!
You can tell they are really nice people from the way the dogs are so attached to them.
I seem to remember, when I was looking at doing something similar in a steel hulled boat that if you don’t put special chemicals in your cement, it will retain water, so if any gets through your floor, or any condensation that occurs it will soak in to the cement and could damage the hull. Maybe different in a wooden boat.
Hi Ben. Will you need to protect the timber under the concrete from collecting inaccessible water? Is there a possibility of it causing rot?
Slow and steady is the way to go. This old fella has never owned a big boat or lived on a boat only boat he's ever stayed on was a cruise ship. It's been fun watching you progress in your abilities. You have taken on a challenge to live your dream where a lot of others would have stopped at rotten wood on your boat in the beginning. Pretty sure you have your contacts that have done this for years and they are giving you some good tips. Love catching up on Sunday mornings.
No such thing as a bad day on the water. Keep being awesome.
Lot's of progress, lots of variety in this episode. Ben and MP, and their furry crew really make this series, but the undisputed star is the stunningly beautiful Yaba!
Ben, Building boats in College while earning My Bachelor of Science in Marine Engineering & Technology, we never used concrete in the hulls. Although there were guys actually building their hulls out of concrete. Hey, it’s your boat Ben, You Do You My Brother. I pray you all stay safe in the name of Jesus, Amen 🙏
Its is so amazing to watch you learn, adapt and keep moving fporward on the boat build.
I do like that jam you were playing while fiberglassing. : )
Enjoy watching all your hard work!! Love the look of your boat. Hope you enjoy it for many years.
Nice video 😊😊
5.000.000 coats??? 🤣🤣🤣 Loved that one ! ! !
Ben, the work on the bathroom floor is nice, but you also have to compensate on the other side of the boat, otherwise the added weight of the concrete and stones skid the boat.
18:42 why not use what they call Crete board and just lay over that so you don’t have to bust that up at every problem underneath there. Or is there not Crete board there where you’re at? Crete board is concrete plywood type and you lay it down and it’s concrete. Not trying to say that you don’t know what you’re doing. In my opinion, I wouldn’t use Crete board but I don’t know the situation. I’m not on the yacht. But hey, love the new boat. Awesome.
Ben you could have a small wind turbine to help recharge your batteries when it is overcast this way you will save fuel and not put unwanted hours on your engine, the concrete was a good idea so long as it hasn’t gone through to the hull , the old girl is looking absolutely beautiful, keep the dream alive best wishes from Tasmania Australia 🇦🇺
Major progress!! As always, thanks for taking us along on your journey.
There are many comments I can make about the bathroom, but it's important that he makes his own decisions and do it as he wants. Mistakes are lessons for the future. I believe it will make him a better sail boat owner and sailor. He's determined and that's a good thing.
its the cement that concerns me if you need to examine or access the hull after a grounding?
Are you not going to reinstall your upper hand rails ? Also way haven't you found a birth so you can have a more stable place to work on your boat. While you tried to catch a fish, MP did something I thought I'd never see happen.... She used your own power to make food, and just seeing that made me feel so good after all this time. What a blessing. Don't go too crazy adding weight to one side without adding it the other side, you don't want your boat to lean. LOL.
neat trick I learned lately is to put the filler in the container and then the resin on top of that. Keeps the filler from going everywhere.
After all the hard work (years)...she is a fine looking vessel especially from the drone footage! Goodonyas, go get'm tiger (s)!
Thank you guys I look forward to the videos every Sunday thanks stan
I would not do the cement in the bilge thing. Remember how difficult it was for you to rebuild the boat.
Just love seeing all the progress. The mast and head are looking amazing.
Boa tarde MP&Ben .😊😊😊
Getting closer to the end of restoring/rebuilding Yaba.
Have fun you guys!
❤ Rockin Roll ❤ guys ❤ love it
Cool tunes, Hammond B3 organ blues is a solid sound while Ben was prepping and fiberglassing. Yeah baby
Beautiful video as usual guys. Always look forward to Sundays.
I guess the only thing I would worry about is water getting down there and not knowing it or it not being able to dry
10:30 ❤❤❤ puppies 🐶
I Love the Bucket!
Where is it dumped??? lol... not very far offshore.
Very good work Ben en MP keep going 👍👍
... love that Yaba' is on the water ... love that you're living your dream ... love that you're getting the head completed, but love even more how the yard dogs have become cruising canines so nicely ... just one question ... who's the boss, you guys or the pups? ...
Ben & MP your intuitions on performing the requisites of accomplishing all of the final tasks on Yaba using the diverse materials is uncanny & I am inspired by your determination to install a complete first class head.
Having to shit in a bucket and then having to handle it, becomes as disgusting as it is also disheartening.
love the progress.
Great job!
Ben illustrated why the plumbing and holes cut into the hull are done before you splash the boat. Not sure about the concrete as it will make it difficult to access that area of the hull as it would be hard to swing a pickaxe in the space of the head and even more difficult to find a jackhammer while at sea to break apart the concrete. But the odds are slim there will be any issues with the area as Ben has it sealed well.
Thanks again for this update! Love it! 😍😍
Composting toilet can be easily installed without need for plumbing.
There are some options to lessen your roll at anchor. I use rocker stoppers. There are other even more effective options.
Hey Y’all. Mark from Atlanta GA. Love the content. Been following since Odd Life suggested you did. Anyway last 5 videos or so you have spots on your lens. Definitely noticeable. I look forward to every Sunday!!
Great update 2x👍
I am so impressed with your journey, enjoy and one question any kids in the future ?
Dentro de poco la desembarca a la marinera y el se queda con todo jaaa😂😂😂😂
What, you are fitting a grey water outlet above the waterline? I hope you like cleaning!
I recently tore out a bathroom on a second floor of a 1926 house. It was concrete. It made for a very stable bathroom.
Love you guys s channel but please next time when doing Bigger pieces of glass just use a foam paint roller much easier
Good work Ben. A word of caution, you might want to consider wearing a mask while sanding the mast. That sander’s dust bag isn’t 100% effective. As a 70 year old carpenter believe me.
Yes, this is true there is also far better products than varnish I use a decking oil Sikkens better results and lasts longer if you want to go cruising get away from varnish or you will be always redoing it looks great, but a lot of work and you could use it on the capping as well as all the outside timber surfaces love watching your videos been watching from the beginning look forward to the next one.
To much wind 🌬️ for that!!
You're right!! We see things much clearer as we get older!! But, What you going to do??
How about a boarding ramp at the swim platform for the dogs to get out of the water?
It really is important to be able to access every part of your hull. If you were to hit something in the water or otherwise, damage the wooden planking, you know cannot get at that area plus the issue of the concrete, attracting water and causing rot. REALLY BAD IDEA.!
As far as the concrete goes ... God help you if you ever need to access that section of the hull -- the loose stone could be moved for emergency repairs, while this is fixed in place. I know that you will not have access as you pointed out, but if you ever hit anything and damage the hull or frames think of all the extra work jack hammering all of that out even on the hard at a yard. I think adding some bags of lead shot would have been the safer solution -- it would have conformed to the gaps, and could still be removed (also denser that concrete so less needed). On another note: during the drone footage early in video the rear mast appeared to have a starboard lean, you may want to check the tension on the stays on both sides port might be loose or starboard too tight -- check the footage. Glad to see you making progress with the boat on the water!! Cheers!
Since he didn"t put any metal reinforcement it will all break up with motion of the boat.
I reckon one job at a time is good.
I am confused…is there no drain? Is this a shower toilet combo and if so, wouldn’t there be a drain before concrete? I am sure you have a plan…I just don’t see it yet ❤❤
Despite others mentioning it, a moisture barrier should always be used between wood and concrete. Moisture will wick out of the concrete forever and cause the wood to rot. Otherwise, great job.
Is there a below decks exit from that forward compartment? It looks like if the hatch got blown shut while you're down there, that hasp could swing shut and lock you in...Just reversing it could fix that...And, wouldn't a 'camping' toilet be a bit better? (a seat on a 5 gallon pail, with plastic bag liners)
What would aldo be cool in a bathroom, tile the floor with flat pebbles.. harder to clean but ballast..
It's so good to see you in the water! Wow,k what a journey!
I am curious about the tender? I saw it when you brought it into the yard. Is it fiberglass? over an inflatable?
I don't remember an episode on the actual tender?
Hello from Australia.🦘
Fico curioso e preocuado com o motor de popa que se perdeu, nao haveria um tipo de sonar que poderia ser alugado para encontra-lo? 😰
Curious have asked this many times do you have the necessary marine tickets to charter and insure?
Lets hope you never have to service/repair any of your through hull fittings in the head. Looks a bit tight in there
Good for you guys!! At least someone is happy!!😮 I just have the bathtub!! And... And? I have to economize on the water!😮 This isn't easy!! 😭 Now!!! I'm going to call the Happiness Police!! Yes, on you!!!
Just kidding, guys!! All the best!! Tudo de Bom para Vocês!!
Hi Ben/MP, why dont you make a small frame to have a place ti fix the satelite internet antenna, and you dont need the ropes to fix it😉
A Vida e boa né 😊
Still need to flip the latch on the forward hatch
Cement keeps moisture and moisture, makes wood rotten !
About 30 seconds of MP. About 1800 seconds of Ben. Ben loves that camera like my doggie loves his frisbee. LOL
But who does the editing?
@@jaygee5693 You can't edit footage that doesn't exist.
concrete holds moister might cause rotting of your framing because there is not any air flow and the moister holding of the concrete.
Made worse by fibre-glassing in the freshly poured concrete. It typically takes 28 days to dry for every 25mm of slab thickness. The only way out for the moisture now is into the hull timber.
That was funny to watch 🥴
I found this info online after watching your your video. Not sure if it applies to your situation.
Can wood be in contact with concrete?
Moisture absorbed by the concrete or masonry may cause the wood to rot - unless that 1/2 inch of space is maintained. Typically, though, the space is closed up for aesthetic reasons, so decay-resistant lumber is used.
Still here :=)
I would have thought the weight of the water will dissipate as it drys?
I wonder, how do you get access to all the plumbing or electrical for maintenance after the bathroom walls are bonded to the floor?
how will water drain??
Concrete takes weeks to fully cure, fiberglassing it in before then will trap moisture below the fiberglass
My thoughts too, but as I tend to make too many critical comments, I bit my tongue. That freshly poured concrete is now encapsulated, complete with freshwater moisture.
I don't like the idea of pouring concrete in the bilge either. It's not an uncommon practice apparently, but counter-intuitive for me. LOTS of work with a pneumatic hammer will now be required to access the hull. I've watched Gemma and Simon removing bags of ballast from Sarinda's bilge, and that was hard enough work already, without having to break up solid concrete.
Edit: I may be mistaken about the fresh concrete being "encapsulated". Ben may have ensured that he left some airflow space between the new head sole and the concrete? Here's hoping!
There seems to be a lot of negative comments about the concrete being used but I’m pretty sure you only put it against painted wood so it should be fine, I can’t see your plan for the bathroom yet I can only imagine that it’s some sort of wet room, but I haven’t seen any floor drain going in so I’m unsure, if it’s just a toilet and wash hand basin you have gone way over the top with the fibreglass, I would say only do one project at a time you will burn out doing so much constantly. Good luck 😊❤
Paint only slows down the absorption. All paints and coatings are permeable to water, just to varying degrees. In this case, the freshly poured concrete was fiber-glassed in before it was cured, so a lot of moisture will be looking for a way out.
About the fiber-glass, I think 1 layer would be the bare minimum for a "dry" head, as water would still be splashed around to some degree. For a wet head a minimum of 2 layers, ideally 3 or more.
whaou you still have the courage to swim 👏👏, what is the water temperature?