How to Replace Front Inner & Outer Wheel Bearing 1993-1997 Ford Ranger
HTML-код
- Опубликовано: 26 авг 2024
- Buy Now!
New Wheel Bearing & Seal Kit from 1AAuto.com 1aau.to/ia/1ASH...
This video shows you how to install a new TRQ wheel bearing and axle seal on your 1993-1997 Ford Ranger. If you hear a grinding or groaning noise while your vehicle is rolling, it might have a worn out wheel bearing. A worn bearing can allow the wheel to wobble, creating a host of other issues. To save yourself from more headaches down the road, replace your bearing right away. For solid rear axles, you'll need to replace the axle seal too.
This process should be similar on the following vehicles:
1993 Ford Ranger
1994 Ford Ranger
1995 Ford Ranger
1996 Ford Ranger
1997 Ford Ranger
Tools you will need:
• Flat Blade Screwdriver 1aau.to/oa/1AXA...
• Pry Bar 1aau.to/oa/1AXA...
• 13mm Socket 1aau.to/oa/1AXA...
• 14mm Socket 1aau.to/oa/1AXA...
• 19mm Socket 1aau.to/oa/1AXA...
• 27mm socket 1aau.to/oa/1AAS...
• 34mm Socket 1aau.to/oa/1AAS...
• Air Compressor
• Brake Caliper Compressor Tool. Dual Piston. Pump Style. 1aau.to/oa/1AXA...
• Brake Caliper Hanger 1aau.to/oa/1AXA...
• Adjustable Wrench
• Side Cutters
• 3/8 Inch Air Impact Gun
• 3/8 Inch Socket 1aau.to/oa/1AXA...
• 1/2 Inch Breaker Bar 1aau.to/oa/1AXA...
• Ratchet 1aau.to/oa/1AXA...
• Torque Wrench 1aau.to/oa/1AXA...
• Drill
• Brake Grease
• Brake Parts Cleaner
• Cloth Rags 1aau.to/oa/1AXS...
• Cotter Pin
• Gloves 1aau.to/oa/1AXS...
• Rust Penetrant
• Safety Glasses 1aau.to/oa/1AXA...
• Brass Punch
• Hammer 1aau.to/oa/1AXA...
• Sledge Hammer 1aau.to/oa/1AXA...
• Wire Brush 1aau.to/oa/1AXA...
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ Watch the Video
√ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts
√ Do it Yourself
√ Save Money
So this job gets a lot easier if you buy new rotors that come with the race installed?
I'm looking at the back of my rotor rn, no wheel seal or inner bearing 🙃
Thank you for sharing this video! I just completed the repair on my 90 Bronco II, and it made the process so much easier. I also opted for the new rotors - runs great now!"
Fantastic video!!!!! Finally a concise mechanic.
You don't have to open the bleeder screw the fluid will go back to the mastercylinder You opened the system now you have to bleed it out I've been doing it that way for decades
Is there suppose to be any play after the bearings snap into place?
Does anyone have any info on replacing rear wheel bearings on a 93 Ford e150? I can't find anything. I know you have to remove gears and pull axles, that's all I know. I'm doing the drum brakes Friday and needed to do everything while I have it up and already working on it. Thanks.
Nice informative vidya as always!
Thanks for the video
Great video, super calm and informative,
Thank you so much for you time,
New subscriber
Great Video 📹 but unfortunately this isn't needed. New Bearings Races are in the new rotors
- Repack Grease in old bearings and smog grease on new races inside the rotor
- Yes there is play but no excess. You shouldn't be able to rock the wheel back and fort if intall correctly.
$ there should only be a shim of play. Tight bolt - remove play Loosen to + play! Once the bearings are fully seated.
Do you really have to replace the race?
I can't believe that you are using those rotors again,the absolutely worst shape possible...junk,junk,junk....
Thanks for the info I just purchased about a mth ago the GEENI outdoor security camera and I did think it would be secure and had plans to buy more but now you changed my mind I don't want a camera that's not secure it defeats the purpose of having one , myself I think they should answer a question alot of people that's bought their product why did they lie , more people need to see this video anyone who's planning on buying one of these , I know I plan to tell anyone that's looking to buy them one to stay awày from them ,again thanks for the good information
Best way to fix them is get rid of it and buy a toyota. These trucks are pieces of sh!t