Get Plans to build your own DIY 10x12 Shed! shop.fixthisbuildthat.com/collections/outdoor-projects/products/modern-10x12-diy-shed-plans If you want to see the rest of the build you can find the videos here: 1. Building a Shed Foundation - ruclips.net/video/XodcMhvfkXg/видео.html 2. Framing a Shed Alone - ruclips.net/video/cGqx95JVsws/видео.html 3. Roofing a Lean-To Shed - ruclips.net/video/Hv3EOTkR3xw/видео.html 4. DIY Shed Doors & Windows - ruclips.net/video/rp3rJUWJeKE/видео.html 5. Finishing My Overbuilt Shed - ruclips.net/video/uPO46hSpP0A/видео.html
Love the New Yankee Workshop safety reference. LOVE that they've uploaded all vids to youtube. Its little nods like that, that prove how inspirational that program was and how far its reach was (and still is).
If you lay your osb horizontal, that is how I was taught to install it, you can use the premarked lines for locating your studs. They usually come with lines for 16 and 24 on center. Then you don't have to snap lines for your studs.
Thats is correct and the sheating is meant to go horizontally because it will catche more studs and add lateral strength. He should of did it like he did his floor sheathing.
I love your building process. It matches what a diy person actually does. Build a little, fix mistakes, build a little, fix mistakes.... I appreciate that when things don't go smoothly and that you keep that on camera. Great job!
I learned a lot building my own shed - one thing I did was extend the back birdsmouth cut so I could slide the siding up under it. Everyone should try their own shed build.
I’m glad to hear that someone else has some trouble building/fixing something’s. You did good, once you got started. I am using your phrase, “Mistakes were made” when I goof something. It’s just soooo true.
When you were using the story stick and moved from the front to the back, I knew for a fact that was the point I would have flipped it or otherwise used it incorrectly and wouldn't have caught it until I was setting the rafters. When you set the fascia board upside down, I could totally see myself doing that too, especially working alone. Thanks for leaving the oopsies in too. You can't learn if you don't make a mistake occasionally.
after the fact I realized the story stick was where I actually went wrong, not the fascia. I marked the stick upside down while looking at the drawing. so actually the fascia should have been correct 😀
the boards on the front and back ends of the rafters are called "sub fascia" and the rafters on the two ends are called "fly rafters" since they are "flying" in space and not over the building. That type of house wrap is an air infiltration barrier, not a vapor barrier. Generally, when doing a roof, we run a shingle up the roof too to establish the overhang. Finally, you did not have to put so many nails in that final drip edge at the top of the roof (end of your work). You could put it down with a generous amount of roofing cement (comes in a caulking tube like the sealant you were using) and then just nailed it a few times. This video was worth the wait from December Brad. Thanks
Good on you for showing your (very minor) mistakes. Most RUclipsrs only show the best bits, which makes the viewer think they should also achieve this perceived "perfection"
Small blocks of framing lumber are prone to splitting. You can pilot drill them, but it's generally faster to drive a nail or screw front to back and that holds the grain together as you drive a fastener the short way. Hook blades are way easier for cutting asphalt shingles. Start your cut 1/2 inch in from the edge and cut that short gap last.
I used the ForceField panels on my backyard office and was very impressed with the panels. They were left exposed for 3 months and I had only a couple of leaks from over driven nails that I was able to fix with flashing. I also did use Zip system tape with the panels because I saw a lot of negative reviews on the GP tape. It worked out great.
I had never done any kind of construction work in my life, but regarding roof installation, it always made sense to me to begin down moving upwards so that whatever material used for roofing gets the overlay gaps on top thus preventing water going down the roof.
Ah yes, back when I was framing houses in college we heard the phrase, "it's getting covered up anyway" fairy often. Hahaha. But for real though, those rafters were just fine, for sure. Great job on this build series. As always, I am really enjoying your videos. Keep 'em coming. Thanks!
The shed is coming along nicely. I do feel your pain in respect to the weather. I started my shop and the weather was great then we got some rain and it wouldn't let up. Since i attached it to my existing garage the roof on it was exposed so the rain got it out too causing some water damage
Great to see you're back working on the shed Brad! It is really taking shape and looks so nice. Thanks for sharing all the tips and also things that didn't go as planned. That helps us all!
A tip for anyone doing a roof soon. A laminate floor cutter (the guillotine style) works awesome on shingles . You get perfect straight cuts every time and is a huge time saver.
H- clips are design to add strength and keep your roof sheating connected between rafters. You may get some uneven sagging spots on your roof. As well wall sheathing is designed to fo horizontally to catch as many studs as possible to strengthen the whole wall. None of those things are major issues on a small shed but would be on a bigger build.
Really awesome work, Brad! It's looking fantastic! 😃 You know, we had to replace a plastic roof here, it's just a small roof over the laundry room... And they installed a sheet of composite aluminum. And... Holy sh*t, you need to take a look at that material! 😮 There was a strip left over from this and they gave it to me. It's going to be freaking useful in the shop for jigs and stuff! Anyway, stay safe there with your family! 🖖😊
Pull layouts for you top plate on ground before you stand your wall up won't need to get up on. The ladder again. Yes I know won't work every Time but it can ALOT
Two years ago I had to replace the roof on the summerhouse at the end of the garden. I had to replace 60m2 (645.835ft2), I used OSB2 2440mm x 1200mm which were 18mm (0.7 inches) thick (2.44m x 1.2m or 8ft x 3.937ft). After removing the very cheap roofing felt I removed the rotten boards, glass fibre insulation and had a break. I replaced all the panels lifting the OSB boards on to the roof using temporary batons to stop the sliding off and fixed them in place, noticing quickly the "professional builders" that had built the summer house didn't know what a square was. Battery powered Circular saw and impact driver were my friend, the sodden glass fibre insulation (after killing all the bugs living in it) was replaced with recycled plastic bottle insulation (it doesn't soak up water and bugs can live in it). Once the roof was finally replaced I went about installing new roof felt, this was thicker and reinforced with glass fibre it was a lot heaver it came in 3m x 1m (118.11 x 39.3701 inch) rolls.. in total eight were used and I covered each OSB gap with bitumen and then used it along each long end of the sheet to secure it in place along with the felt nails at 100m (3.93701 inches) apart. The whole replacement of the roof took four days with breaks to get new insulation or to get more screws and lift materials in place. Yeah metric is difficult... I count to 10 and you are welcome to your fractions.
Brilliant, can’t wait for the walls now :) soon as you do that video I’m going to follow step by step to make my shed :) love you and your family love the channel content :)
Good to see the shed getting done. If you do more work with shingles I would highly recommend getting some hooked blades for your utility knife. Works much better than the normal blades!
Great job! Every time someone shows laying shingles they warn to avoid wind sheering to NEVER use less than a one-third sheet when ending a row. I can't wait till Christmas to see the lap siding go on.🤪😜
Very informative videos! I’m a first time home buyer and I was looking to build a shed as well as a greenhouse on my new property. I’m thankful for your videos and I would like to purchase some plans if available.
9 minutes or so... its not a ridge board its called either sub-fascia or fascia fepends on how it finishes. A ridge is where the two sides of the rafters/roof meet in the middle.
You are my favorite RUclipsr woodworking person. You show that mistakes happens but we have to deal with that and accomplish what we want to do. Not the traditional channel where everything is perfect and pretty 😂.
Doug all of those trees are worth the effort. The first tree cut into sections that you can move with your excavator. The second leave attached to the tree and section it off until you get to the tree. Again use your excavator as possible for assistance. The next 2 your ideas are correct get the weight off the tree and cut it. When cutting off your stump use you excavator bucket and cut from it. Cut the base and pull down hill. The ones you said you would leave. Leave them. The last one is very tough. Having a crane or bucket would be the best way. All of them would be extremely expensive to hire out.
I feel honored you featured my comment! Lol this is perfect timing because I'm about to redo my shed and I'm nervous about doing the roof. Love your channel, keep it up.
Just a note. H clips are used for spacing, but with a 24” spread on the rafters, the h clip provides strength from one sheet to the next. 7/16 osb should have an h clip for everything over the diamond layout (19.2 inches).
Nice job! I really would have encouraged you to use 5/8 sheathing on the roof though! Especially because of the rafter spacing and low pitch. Unfortunately you will get sagging. Perhaps you can add some blocking between the rafters preventatively
I don't know about shingles on a 2/ 12 pitch, 3/12 is usually the minimum. should have used a rolled roof, just saying I have been doing this stuff since I was 20, that's 40 years. just aged me. lol.
Your videos are awesome!! So clear and love how you show your mistakes 😂 I'm going to build a shed soon and pretty sure will make some too. Keep up the great work man! 😊
Same here, grew up on TNG, Voyager, DS9. I enjoy when the creator and editor have a good banter. Hopefully I can find that one day. I'm also a HUGE Star Wars fan, lol probably one of the few how loves both. @@Fixthisbuildthat
If you'd just used the same paint on the fascia (or any old / leftover paint) on the backside of some standard OSB, you'd have made your own "Force Field" but better. Especially if you paint all of their edges as well. Edge first, then install, then use a roller on the entirety.
AbAbsolutely Amazing job on your shed build project! I really appreciate your common sense approach to the building process! I really like the selection of products for your shed project build, too! Well done, Sir!
Very cool build and I really like the story stick idea. It expedite the process of marking and laying out the rafters. I also appreciate you leaving in your mistakes.
Did I hear you channeling Norm? After all you've done in this video, I'd be worthless for a week. I'm looking forward to seeing the rest of the build, as long as I don’t have to do the work (I'm old). Bill
You should have put the drip edge on the front edge of the roof when you were doing your second to last row of shingles, once the drip edge was nailed down you could’ve put the last row of shingles on top of the drip edge, you would just peel up the keystone and nail under those then reseal
A two on twelve pitch is really pushing the envelope and increases the probability of wind driven rain getting between the shingles and the membrane. Back in the day the manufacturer recommended increasing the lap of the shingles on two twelve. Not possible today as the sealing strip tech is different. I would consider four twelve the minimum with five twelve still easy to stand and work on without slipping while walking the roof.with a five twelve, the rafter length is only an inch wider for each foot the rafter covers per foot of building width. It is exactly .97 ,but you get the idea. It becomes even more important if you heat the building to work inside because of ice dams becoming more of a problem. Other than that, you did a much better job than most by laying things out on the ground instead of chasing a tape measure Found the top plate with a marking pencil as Most people do
Brad, was there any reason why you chose asphalt shingles over a metal roof? I am going to have to replace the previous owners shed this summer and was just curious on your thought process for it. Really impressed with the tips shown sir!
Get Plans to build your own DIY 10x12 Shed! shop.fixthisbuildthat.com/collections/outdoor-projects/products/modern-10x12-diy-shed-plans
If you want to see the rest of the build you can find the videos here:
1. Building a Shed Foundation - ruclips.net/video/XodcMhvfkXg/видео.html
2. Framing a Shed Alone - ruclips.net/video/cGqx95JVsws/видео.html
3. Roofing a Lean-To Shed - ruclips.net/video/Hv3EOTkR3xw/видео.html
4. DIY Shed Doors & Windows - ruclips.net/video/rp3rJUWJeKE/видео.html
5. Finishing My Overbuilt Shed - ruclips.net/video/uPO46hSpP0A/видео.html
❤
❤
What is the estimated cost of materials for this project?
Love the New Yankee Workshop safety reference. LOVE that they've uploaded all vids to youtube.
Its little nods like that, that prove how inspirational that program was and how far its reach was (and still is).
Started watching those on YT, nice to see them preserved as I used to watch them when I was young along with This Old House.
If you lay your osb horizontal, that is how I was taught to install it, you can use the premarked lines for locating your studs. They usually come with lines for 16 and 24 on center. Then you don't have to snap lines for your studs.
Thats is correct and the sheating is meant to go horizontally because it will catche more studs and add lateral strength. He should of did it like he did his floor sheathing.
Ha! Just yesterday I was thinking: “I wonder if that guy ever finished building his shed…?”
Spring has sprung so I'm back!
I love your building process. It matches what a diy person actually does. Build a little, fix mistakes, build a little, fix mistakes.... I appreciate that when things don't go smoothly and that you keep that on camera. Great job!
I learned a lot building my own shed - one thing I did was extend the back birdsmouth cut so I could slide the siding up under it. Everyone should try their own shed build.
I’m glad to hear that someone else has some trouble building/fixing something’s. You did good, once you got started. I am using your phrase, “Mistakes were made” when I goof something. It’s just soooo true.
When you were using the story stick and moved from the front to the back, I knew for a fact that was the point I would have flipped it or otherwise used it incorrectly and wouldn't have caught it until I was setting the rafters. When you set the fascia board upside down, I could totally see myself doing that too, especially working alone. Thanks for leaving the oopsies in too. You can't learn if you don't make a mistake occasionally.
after the fact I realized the story stick was where I actually went wrong, not the fascia. I marked the stick upside down while looking at the drawing. so actually the fascia should have been correct 😀
the boards on the front and back ends of the rafters are called "sub fascia" and the rafters on the two ends are called "fly rafters" since they are "flying" in space and not over the building. That type of house wrap is an air infiltration barrier, not a vapor barrier. Generally, when doing a roof, we run a shingle up the roof too to establish the overhang. Finally, you did not have to put so many nails in that final drip edge at the top of the roof (end of your work). You could put it down with a generous amount of roofing cement (comes in a caulking tube like the sealant you were using) and then just nailed it a few times. This video was worth the wait from December Brad. Thanks
top tip for any shed, make the over hang massive so water never hits the sides or soak the foundation and potential rot the sill plates
yup, I went with as much as a I could to fully use the lumber I bought
Good on you for showing your (very minor) mistakes.
Most RUclipsrs only show the best bits, which makes the viewer think they should also achieve this perceived "perfection"
we embrace the mistakes around here
Plus, at 200 mph, you won't see 'em driving by. 😁
Small blocks of framing lumber are prone to splitting. You can pilot drill them, but it's generally faster to drive a nail or screw front to back and that holds the grain together as you drive a fastener the short way.
Hook blades are way easier for cutting asphalt shingles. Start your cut 1/2 inch in from the edge and cut that short gap last.
I used the ForceField panels on my backyard office and was very impressed with the panels. They were left exposed for 3 months and I had only a couple of leaks from over driven nails that I was able to fix with flashing. I also did use Zip system tape with the panels because I saw a lot of negative reviews on the GP tape. It worked out great.
I had never done any kind of construction work in my life, but regarding roof installation, it always made sense to me to begin down moving upwards so that whatever material used for roofing gets the overlay gaps on top thus preventing water going down the roof.
yep, exactly!
Ah yes, back when I was framing houses in college we heard the phrase, "it's getting covered up anyway" fairy often. Hahaha. But for real though, those rafters were just fine, for sure. Great job on this build series. As always, I am really enjoying your videos. Keep 'em coming. Thanks!
The shed is coming along nicely. I do feel your pain in respect to the weather. I started my shop and the weather was great then we got some rain and it wouldn't let up. Since i attached it to my existing garage the roof on it was exposed so the rain got it out too causing some water damage
yeah, doing a project by yourself over many weeks makes dealing with weather a big unknown
Thank you for dumbing down the rafter tail cuts...been wondering how to do that for years.
Great to see you're back working on the shed Brad! It is really taking shape and looks so nice. Thanks for sharing all the tips and also things that didn't go as planned. That helps us all!
The ghost deer get me every time! 🤣🤣🤣
A tip for anyone doing a roof soon. A laminate floor cutter (the guillotine style) works awesome on shingles . You get perfect straight cuts every time and is a huge time saver.
ya mero voy andar subiendo esa herramienta al techo, mejor navaja de gancho
H- clips are design to add strength and keep your roof sheating connected between rafters. You may get some uneven sagging spots on your roof. As well wall sheathing is designed to fo horizontally to catch as many studs as possible to strengthen the whole wall. None of those things are major issues on a small shed but would be on a bigger build.
Minor mistakes and all, you are doing a terrific job building that shed yourself Brad! Great job!! 👍👍🔨🔨
Really awesome work, Brad! It's looking fantastic! 😃
You know, we had to replace a plastic roof here, it's just a small roof over the laundry room... And they installed a sheet of composite aluminum. And... Holy sh*t, you need to take a look at that material! 😮
There was a strip left over from this and they gave it to me. It's going to be freaking useful in the shop for jigs and stuff!
Anyway, stay safe there with your family! 🖖😊
that sounds cool!
Pull layouts for you top plate on ground before you stand your wall up won't need to get up on. The ladder again. Yes I know won't work every Time but it can ALOT
good tip
Love the Norm Abram reference!
Thanks for the video. I was looking forward to this one. Makes me want to try to build a shed
it's not any easy process, but rewarding
Two years ago I had to replace the roof on the summerhouse at the end of the garden.
I had to replace 60m2 (645.835ft2), I used OSB2 2440mm x 1200mm which were 18mm (0.7 inches) thick (2.44m x 1.2m or 8ft x 3.937ft).
After removing the very cheap roofing felt I removed the rotten boards, glass fibre insulation and had a break.
I replaced all the panels lifting the OSB boards on to the roof using temporary batons to stop the sliding off and fixed them in place, noticing quickly the "professional builders" that had built the summer house didn't know what a square was. Battery powered Circular saw and impact driver were my friend, the sodden glass fibre insulation (after killing all the bugs living in it) was replaced with recycled plastic bottle insulation (it doesn't soak up water and bugs can live in it).
Once the roof was finally replaced I went about installing new roof felt, this was thicker and reinforced with glass fibre it was a lot heaver it came in 3m x 1m (118.11 x 39.3701 inch) rolls.. in total eight were used and I covered each OSB gap with bitumen and then used it along each long end of the sheet to secure it in place along with the felt nails at 100m (3.93701 inches) apart.
The whole replacement of the roof took four days with breaks to get new insulation or to get more screws and lift materials in place.
Yeah metric is difficult... I count to 10 and you are welcome to your fractions.
Brilliant, can’t wait for the walls now :) soon as you do that video I’m going to follow step by step to make my shed :) love you and your family love the channel content :)
thanks, Thomas!
@@Fixthisbuildthat your very welcome. All your content is great, I love the fact you leave in your little mistakes to show we’re all human :)
it's coming along and looking awesome! Before you know it, Susan will claim it as her she-shed :)
thanks, Keith!
The editing in between nail shots... respect
Good to see the shed getting done. If you do more work with shingles I would highly recommend getting some hooked blades for your utility knife. Works much better than the normal blades!
Outstanding next level quality build,,,,great job
Working out doors in the winter is no joke. I dont blame you for holding off
Goodness gracious great balls of fire.
Fantastic job on the roof installation! It really ties the whole shed together beautifully. 🏠
Great to see the salvaged boards. Too many RUclipsrs throw away perfectly good boards after remodels.
Nice to see the Ghost Deer hanging around, contentedly chewing some Ghost Grass 😊
Great job!
Every time someone shows laying shingles they warn to avoid wind sheering to NEVER use less than a one-third sheet when ending a row.
I can't wait till Christmas to see the lap siding go on.🤪😜
Very informative videos! I’m a first time home buyer and I was looking to build a shed as well as a greenhouse on my new property.
I’m thankful for your videos and I would like to purchase some plans if available.
Brad, the best part is you are doing this all yourself.
my body would disagree
@@Fixthisbuildthat I hear that!
Not the ghost deer in the background 😂🦌
Thanks for getting back to this project!
love the part you realized that face plate was longer on one side than the other so funny...and yes I have made these mistakes and still make them
happens to the best of us 😂
Thank heaven for screws
9 minutes or so... its not a ridge board its called either sub-fascia or fascia fepends on how it finishes. A ridge is where the two sides of the rafters/roof meet in the middle.
ahhhh, good to know
In this case, it would be sub-fascia.
You are my favorite RUclipsr woodworking person. You show that mistakes happens but we have to deal with that and accomplish what we want to do. Not the traditional channel where everything is perfect and pretty 😂.
Doug all of those trees are worth the effort. The first tree cut into sections that you can move with your excavator. The second leave attached to the tree and section it off until you get to the tree. Again use your excavator as possible for assistance. The next 2 your ideas are correct get the weight off the tree and cut it. When cutting off your stump use you excavator bucket and cut from it. Cut the base and pull down hill. The ones you said you would leave. Leave them. The last one is very tough. Having a crane or bucket would be the best way. All of them would be extremely expensive to hire out.
Try starting in June when summer is coming 90 degree
I feel honored you featured my comment! Lol this is perfect timing because I'm about to redo my shed and I'm nervous about doing the roof. Love your channel, keep it up.
I really missed those deers man!! Great build
Just a note. H clips are used for spacing, but with a 24” spread on the rafters, the h clip provides strength from one sheet to the next. 7/16 osb should have an h clip for everything over the diamond layout (19.2 inches).
You’re looking for fascia board.
Nice job! I really would have encouraged you to use 5/8 sheathing on the roof though! Especially because of the rafter spacing and low pitch. Unfortunately you will get sagging. Perhaps you can add some blocking between the rafters preventatively
I don't know about shingles on a 2/ 12 pitch, 3/12 is usually the minimum. should have used a rolled roof, just saying I have been doing this stuff since I was 20, that's 40 years. just aged me. lol.
+1
Excellent video! I like that most of the video you were on your own. Good hacks to help when you are on your own.
Your videos are awesome!! So clear and love how you show your mistakes 😂 I'm going to build a shed soon and pretty sure will make some too. Keep up the great work man! 😊
Dear Editor, Thank you for the Piccard facepalm. That is all. lol
yes, I thoroughly enjoyed when Chris put that in. Was a huge STNG fan back in the day
Same here, grew up on TNG, Voyager, DS9. I enjoy when the creator and editor have a good banter. Hopefully I can find that one day. I'm also a HUGE Star Wars fan, lol probably one of the few how loves both.
@@Fixthisbuildthat
drip edge - didn't know about that part
Thank you for making me and my splitting support blocks feel normal 😅
If you'd just used the same paint on the fascia (or any old / leftover paint) on the backside of some standard OSB, you'd have made your own "Force Field" but better. Especially if you paint all of their edges as well. Edge first, then install, then use a roller on the entirety.
Bonus points for the Norm Abram callout.
looks good, if you didn't have enough waste for the blocking, your have to use a 2x6x8 and break it down anyway. lol
I like how you sped up the triple chopsaw cut sound to match the tempo of the music
God I love shed videos 😜
just trying to keep on your timeline...4 months to go
The nod to Norm....... love it.
Thank you!
AbAbsolutely Amazing job on your shed build project!
I really appreciate your common sense approach to the building process!
I really like the selection of products for your shed project build, too!
Well done, Sir!
Just the tips I needed! Thx "LIKED"
Very cool build and I really like the story stick idea. It expedite the process of marking and laying out the rafters. I also appreciate you leaving in your mistakes.
out of all the silly sally quotes and blurbs on all of utube.... MISTAKES WERE MADE... is the best, been using it for many years, LOL... smFh
Excellent video as always! 👍
Noticed only one moose ghost.. 😂
I love the Norm Abrams nod!
Great video, I was wondering what was going on with this build. LoL
Keep them coming
You should use nails instead of screws for framing. And install OSB horizontal
Normally you would use a hook blade when cutting shingles. Makes it much easier to cut.
Agreed, but cutting from the backside makes it pretty easy if you don't have a hook available
Good luck with your new shed
thanks!
@2:41 Thanks Norm!
Longest Shed build series I have watch thus far :-)
guess you didn't watch @shopnation shed build then 😂
Did I hear you channeling Norm? After all you've done in this video, I'd be worthless for a week. I'm looking forward to seeing the rest of the build, as long as I don’t have to do the work (I'm old).
Bill
oh yeah, I'm trying to carry the flame for Norm! And you can't imagine how sore I am right now, lol
very helpful - thank you.
Always amazing to see how many more nails someone will use out of a gun instead of screws.
That deer ghost is a easter egg maybe😂
18:50 What uh... whatchu doin' there bud? 😂🔨
😂😂 hitting with smooth side of hammer so the waffled face doesn’t tear up the waterproof membrane
This man took a 3 day project to 2 years
Great job!
Thanks!
You should have put the drip edge on the front edge of the roof when you were doing your second to last row of shingles, once the drip edge was nailed down you could’ve put the last row of shingles on top of the drip edge, you would just peel up the keystone and nail under those then reseal
Nice job! Simple sheds are not that simple.
no they are not
Nice,thanks for the tips
You bet
This Old House or This New Shed lol .. Loved the reference :)
The yellow tape for the roof, its good, but the zip is way,way better.
3:30 nice touch with the ghost
Just realised there are ghosts through outh the video 👻
wow, thanks for sharing my friend, great new share
I enjoyed the Norm Abram quote!
A two on twelve pitch is really pushing the envelope and increases the probability of wind driven rain getting between the shingles and the membrane. Back in the day the manufacturer recommended increasing the lap of the shingles on two twelve. Not possible today as the sealing strip tech is different.
I would consider four twelve the minimum with five twelve still easy to stand and work on without slipping while walking the roof.with a five twelve, the rafter length is only an inch wider for each foot the rafter covers per foot of building width. It is exactly .97 ,but you get the idea. It becomes even more important if you heat the building to work inside because of ice dams becoming more of a problem.
Other than that, you did a much better job than most by laying things out on the ground instead of chasing a tape measure Found the top plate with a marking pencil as
Most people do
Thanks norm great build
Thank you for the safety tip Norm
"Whacka-Slapperoo" is now the official name for...Whatever that thing used to be called! I don't actually know what it's called. LOL
I always call to the hammer stapler
Great video, and I liked your nod to Norm, and the ghost of a buck later in the video.
Brad, was there any reason why you chose asphalt shingles over a metal roof? I am going to have to replace the previous owners shed this summer and was just curious on your thought process for it. Really impressed with the tips shown sir!
Remember that Norm added hearing protection when using power tools!
8:15 I'm in the long, drawn out process of building an outdoor catio. Some of this is helpful to see..
9:10 I've played this game.. lol