How To Make Motion Sensor Light Homemade

This is motion sensor light. This light work on human motion. Such that if there human motion is present then light goes to on state and if there are no human motion light goes to of state. By this process you can make or connect outdoor light.
PIR Motion Sensor Switch: • Motion Sensor Switch
PIR Module Review And Testing : • Motion Sensor Module R...
Parts:
1) HC-SR501 motion sensor module
2) PVC Box
2) Switching Circuit
Cover songs collected from NCS youtube channel: / nocopyrightsounds
Song 1: • Video
Song 2: • Elektronomia - Limitle...
Please subscribe my channel for more update: goo.gl/WfYhoR
Please Like our facebook Page : / eassytech
~-~~-~~~-~~-~
Please watch: "How To Make 4x4x4 LED Cube"
• How to Make a LED Cube...
~-~~-~~~-~~-~

[@sweatygamer7685]

Great video! This will help me for my ALP project!!! Thanks a lot!

[@easytechzones]

Thanks

[@anandjoshi8554]

@@easytechzones in re trigger mode H > if u increase delay time > then after u left the room, output/load remain high ,until the end of duration of delay time set !!!!

[@naboulsikhalid7763]

I liked what I watch, brilliant project, keep being creative. don't get down with negative comments. RUclips is about creativity and sharing knowledge. Thanks for doing both.

[@MrVilaskhare]

The same item i had made in the same way . I have given two pin socket instead of plain Holder for bulb. Due to this i.e. 2 pin socket, anybody can use multiple item i.e. led, radio, tape recorder, small light mal, buzzer etc. The circuit idea is best and working well.

[@drelectronics13]

Very good idea sir

[@harryhobbyist941]

Nice video. Would be ideal if you could give detailed names of components used in description .....

[@Rudy80417]

5 volt,pir,transistor,relay=magic..............,.....good boy......

[@abdullahsaqib8471]

Parts used in this video
Bc547 transistor
HC-SR 501 motion sensor
Diode 4700
12v relay
Connecting terminals.
Plastic box

[@reynaik4381]

Hoe much does this cost ?

[@abdullahsaqib8471]

@@reynaik4381 it didn't cost much expensive. I would day it around 15$ in my currency.

[@ppolleunus]

Thanks for the video. At 2:05 you say that the circuit diagram link is in the description but it's not there.
For newbies, you should add the details of all components in the description. What diode, transistor and relay is needed?

[@MasKimochi]

diode 1N4007
resistor 1k 1/2watt
bc547

[@dudleychristoffelsz]

I also thought of the same thing it's difficult to build a circuit with out knowing all of the components,the video is also to farst to follow,specially for learners.Thanks for the effort made in uploadtng the video.

[@AnwarHussain-se9fh]

Just buy a motion sensor bulb.much cheaper and elegant.but this is nice for learning .

[@mission_critical]

nice video, you should include circuit diagram and avoid using soldering iron for holes, get a drill machine or dremel.

[@himangshubaruah5856]

he’s comfortable with soldering iron. Just saying

[@RegmiSudip]

@@himangshubaruah5856 It is not good for health to use soldering iron. Fume coming from melting different kind of plastics can derail your life.

[@martiishere]

Mission Critical Niel Diamond

[@tanvinrayhan]

I even smell burnt plastic when he used the soldering iron to make that hole

[@niteshyadav0903]

Solder iron might get damage due to plastic hole. I burned one

[@duynguyen6229]

Excuse me! I would like to ask you something that: "What would happen if the bulb is still on and we make another movement for the sensor? I mean if that movement could make the bulb turn on longer or it won't give any effect to the bulb?
And when the sensor detects a movement, how long does it call the bulb turn on?
Thank you very much for your useful video!!!! Like!!

[@efmuin]

Om,
selama lampu menyala, kemudian ada gerakan orang, tidak akan membuat lampu itu padam. Lampu akan terus menyala sesuai dg durasi yg diatur sebelumnya pada potensiometer yang terdapat pada sensor PIR.

[@rmdharan6895]

As a switch it will act once only and remain as long as motion exist i think

[@kiranshashiny]

There is a SINGLE TRIGGER and RETRIGGER mode settings on the Motion sensor. Single Trigger means - trigger once the motion is detected and stops.
Retrigger is - if the motion is still there - then it continues enabled until the motion is not there ( or person moves out of range )
there are pins on the motion sensor H and L - check it out.
You need the Retrigger setting.

[@xperimentsqf3823]

@@kiranshashiny thanx for the answer

[@rajeevgupta3154]

150 ka to bana banaya hoder mil jata hai

[@rmhutchins7]

I enjoyed your video. It was very helpful. Thank you!

[@jeanlouisgeorges509]

Good job

[@easytechzones]

Thanks

[@techmahfuzbd]

Nice video.

[@vedansh537]

Very good

[@ledmk2]

Nice made

[@eswaramoorthyarunachalam7961]

Super
How much distance it response?

[@manishvijayan1725]

Sir relay module ka connection ka ek video banaiye step by step please

[@jasir12mehraj43]

One advice next time make video with voice. That will ne more helpful.

[@easytechzones]

Ok

[@practicallab]

Nice

[@easytechzones]

Thanks

[@oye_chudhary]

Outclass bro...keep it up...but plZ tell me the name of circuit and this sensor circuit... Thanxx

[@theoneevans7790]

Cool electronic house stuff.

[@areejotif8535]

very intelligent

[@mohammadammad4068]

nice
#electro ad

[@easytechzones]

Thanks

[@AbnuCPaul]

Great work 👌 👏
👏 ❤️

[@akashKumar-pw9rd]

Fain reguletar bhi laga sakte hai tej karne ke liye

[@dimitrischaralampopoulos177]

an i use a proximity sensor for trigge and use it to wire a siren for 10sec?

[@VrFunpark.Jaipur]

Mai de sakta hu 10 sec ka

[@novato200]

Hi. Sr, Good video, is the same way for 120v. If not coul you tell me. Please. How many wa. Is the bul
Thank you.

[@vikrambuilds]

It will be the same, just make sure the AC-DC adapter is 110volt AC to 5volt DC

[@intekhabahmedkhan3431]

thanks

[@ItaloLima]

Nice Video !!

[@intekhabahmedkhan3431]

good video

[@SalimSheikh-tt4bw]

nice song nd sensor good job boy

[@dimitrisgkiousas8928]

thanks!!!

[@voiceoftruth1O1]

Where is other parts list in description ?
aapaka har veediyo achchha hai krpaya hamen vivaran den.
Diod value?
Transistor ?
Relay volt ?
Everyone is not expert like you. So please give full parts list. We love your work. Hope you help us. thanks

[@voiceoftruth1O1]

EASY TECH : I m waiting for your reply. Please give parts details. I want to make your circuit in real life. Thanks

[@RaoSanjay3839]

1k resistance. Bc547 transistor. 5vdc relay..

[@slbots]

diode -4700
transistor C828 or D400
5v relay is better then we can use old mobile phone charger as the powe supply

[@rafaelconur1191]

Your already genius to me bro!

[@NanoCreator]

ruclips.net/video/fGwg3Tk-xtg/видео.html

[@brendarichardson7271]

Great

[@ukmuhammed6342]

mad range
how man

[@vamshisaikrishnaarelli9778]

I want the light to turn on immediately I enter the room & should stay ON until I left the room. It should not turn OFF while am in the room. Will it work this way?

[@creativetechnology7710]

Please give reply for this

[@morflingmorsa5037]

@@creativetechnology7710 you can set the timer longer... using the time adjuster on the module

[@Karthik-hn8qw]

Use arduino

[@riddhi6535]

Hii...if a object comes in the bulbs diameter, will it turn on automatically??? And if the object later goes far, will it turn back off???please reply ASAP sir, I just have few days left to create my model 😕

[@mdnssanu2017]

ভাল

[@rakeskraj6892]

super osm thanks i did this project at home

[@rjbagyan161]

Diagram and materials pls so I could try it.

[@girishchincholikar]

More complicated than I thought. Do you have more simpler version to this ?

[@tikianokakingo6072]

Can I get a motion sensor which can detect a humanbody only?

[@kiddanhelli4073]

Tell me what is the blue and orange coloured component

[@samiulhridoy9326]

Blue color somponent is relay.... And orange color is connector

[@frankjay6533]

Danny reduce time to 0sec, to turn off light as soon as there is no motion

[@mayurrock2099]

yes time can be adjusted to 0.3 sec to 5 min

[@Phil926]

The number of videos that present great information but become unwatchable because they picked the most annoying music known to man ....

[@easytechzones]

Suggest some music

[@Phil926]

It's hard to suggest music by name since I don't know the names of many songs that are just musical for presentation purposes and I further don't know which are usable without violating copy write issues ... However, while the following might not be excellent by any means its not horribly annoying and doesn't sound like a slide whistle getting gang banged by a bike horn, a clown nose, and an angry dog chew toy:
ruclips.net/video/6tbKm9pJhZQ/видео.html

[@pillalsidar785]

Bolta to like share jaroor karta

[@NguyenHoangMario]

Excuse me . which led bulb support fading on/off ?

[@YaseenExperience]

❤❤❤❤❤👍👍👍👍👍

[@MrNams]

My hc-sr501 gives always high output, what is issue?

[@easytechzones]

Need to change value of timier pot

[@abhasrivastava5746]

Good job bro

[@cvshsrjpmatl3044]

thakyou

[@gauravsingh634]

hey nice video . please tell me how to connect more than two pir motion sensor with one security alarm for house security. so that if any one detect any movement than alarm will activate

[@gokhila.b2312]

Use an arduino. Circuits and codes are easily available...

[@litocollege7521]

Sir please provide me the value of all component, its nice project..thanks

[@BR-rg9ib]

Cool.... Can we use 5v single channel relay...?

[@offgridlife8448]

nice work

[@sajjadshahsajjad3651]

Which empair resister use used

[@ElectronicsVerma]

Register..electronics verma RUclips channel

[@lawnxil1704]

Why are we using that diode?
Will the circuit work properly without that diode?

[@shreekhodiyarfashion2]

I need this circuit but use ultrasonic sensor plz make one video on ultrasonic sensor automatically on off light without arduion plz make

[@easytechzones]

Ok

[@shreekhodiyarfashion2]

When make this video plz fast make i need this plz plz

[@shreekhodiyarfashion2]

Hi Bro When Upload New Video Ultrasonic Sensor Project Whiteout Arduanio

[@frankchang436]

It would be better if including the on-time adjustment scenario and with day/night time control

[@striesDIY]

The motion sensor has a potentiometer to vary the delay time

[@frankchang436]

@@striesDIY yes, I got it.

[@Investerpower]

What is total cost of this model?

[@igotsomespace]

Very creative project, but so much is not explained, and with this being an electrical project, you should be explaining as many safety tips and precautions along the way for people who are absolutely new to this.

[@easytechzones]

Ok

[@rishabhkumarmaurya4045]

Which device you used at video timing 2:07..
I'm working on it for college project so please respond quickly... And the name of diode also...

[@easytechzones]

12v relay

[@i-Ayham]

you need to upload new one with LED light bro 🙂

[@easytechzones]

Ok. Next video

[@NanoCreator]

ruclips.net/video/fGwg3Tk-xtg/видео.html

[@manlikezakaado6135]

will the bulb be on if there is someone but not moving

[@parvezbakht8982]

Transistor number is not mention in circuit diagram. so which transistor is used ???.......

[@Fungineers]

Well done! Keep it up. Would have been simpler to use a microcontroller like an Arduino.

[@venkythummala]

Sir, I want total components. Aap bejsakthe kya. Please.

[@techsummit2941]

Can we control on time of light?

[@ElectronicsVerma]

Electronics verma RUclips channel on time off light

[@bhadreshmewada7790]

I like but without circuit only use motion detection switch

[@easytechzones]

Oh

[@Electron6807]

Ya human body motion ko detect karta hay ya kisi bhi chees ka motion ko please raply it

[@gopalswaroopvyas7456]

Could you tell us how much all this cost and where can I buy those? Couldn't find all those items in my city?

[@junjuncobar7027]

what is the value of transistor?

[@FarazKhan-rd5ow]

How many meter Its detaction

[@prashanthjadavmp]

Can i use Siren instead of light. For security reason.

[@tab529]

Where is the List of Components and Circuit Diagram to allow us to assemble the said motion sensor .

[@ideA_chanel]

What the transistor?

[@michaelcrabtree2939]

I need to get me one of those. great video.

[@GujaratiDiL]

Ek relay 5v ke sath ac kitne bulb or light. Jod sakte he ?????

[@sumalathagovindula1233]

Sir: how to make connected motor or fan same used sensor ?? Upload videos and clarity ckt diagrams

[@slbots]

i also can help you brother
ruclips.net/video/9tjgOxqGSSke/видео.htmlr

[@subashramesh7378]

Why we are not using resistor, without resistor it would spoil ri8

[@SambhuNathChatterjee]

Relay number, transistor no, diode no not given.

[@The89tv]

dear is this run on 220v direct LED

[@1983lalit]

Hi sir moction sensor me easa ho sakta hai ke man jab tak room ke ander rehe light on rahi jest hi bhar nikal jaye light switch off ho jaye.moction sensor me timer laga raheta hai man room ke ander bhi rehe according to time light off ho jaate hai.is timer ko kese by pass kare.

[@dilwaledhanush8799]

Mujhe connection pata nahi chal hara hai pls madad karo circuit diagram me relay ke middle pin kaha connect kare batado pls

[@nomanhabib396]

Recently i use it. But it does not work in day,work only at night. Have you any idea about this problem?
Help me!!!

[@saikatd9037]

please tell the name of transistor used in this ckt

[@easytechzones]

BC547

[@singhp5990]

plse advice where to buy motion sensor and other parts.

[@nvishwa1249]

Can a class 12 student understand this? ?

[@slbots]

yes ,this will be help you
ruclips.net/video/9tjgOxqGSSk/видео.html

[@Sdev-ws2bf]

Better not to play with ac supply,instead use DC operated bulb, LED light or buzzer etc with lower voltages like 6 or 12 volts in place of 220 v bulb . That way you can avoid Ac supply and learn how it works.you can make many interesting projects which are dc operated.this video is for mature people who know what they are doing and know the theory very well before hand.

[@dhanushkv0242]

Can I use 6v relay

[@ElectronicsVerma]

6v relay wiring..electronics verma RUclips channel

[@karangoyal5511]

I am trying to makw it..but my light is not working..please help me

[@illfather7066]

How do you make a motion censor detecter....it was just there

[@mickypathak6313]

bhai ye bataiye ki isame 12v ka v supply chahiye???

[@dhanashreemore3987]

if the plase of the bulb we can joing the motor

[@boringabc]

I am using same Sensor and same circuit, my issue is even though we are in room/ bathroom but light is getting switch off after timer set time, light should be on only till person in room, how to solve this issue?
Jumper is on H only on PIR circuit

[@easytechzones]

Increased Time on sensor board

[@boringabc]

@@easytechzones I tired that but after that it switch off light....

[@gdsrourkela]

Radar Sensor are more sensitive better for bathrooms. Search in Flipcart "Beeper Hobby Kit" you can get a sensor driver kit runs with 230v directly..

[@rameshbasnet1504]

what instrument s included in here?

[@cassandra9675]

Hi! How much is the total cost?

[@jesuschannel6116]

Hello vedio podrathu perusu ella mathavangaluku puriyura pola podunga

[@udit88behera755]

Thanks for making this DiY.

[@NanoCreator]

ruclips.net/video/fGwg3Tk-xtg/видео.html this too~~

[@sharath8077]

Our side 5v circuit not there, but 12v smps is there 12v connected?

[@sharath8077]

Sir example I have connected 12v smps through pir sensor out put same volt came? Diode and transistor mandatory?

[@sharath8077]

@@easytechzones thank you so much your support sir

[@sharath8077]

@@easytechzones sir please send Resistor diode & Transistor value

[@rajesh-ol3gv]

U can mobile charger also