5:33 dude you're a frigging hero! I went to pick mine up with the tweezers and ended up pushing the socket sideways which cause the golden contacts in the center slide off haha To anyone attempting this, be extremely careful to lift it upright
Урррраааа!!!Получилось!!!!Отремонтировал поломанную ножку в сокете,хотя у меня нет специального оборудования и запасных ножек на замену.Взял подходящую заготовку и при помощи надфиля вручную выпилил аналог ножки.Тут главное - не допускать,чтобы обрабатываемая заготовка не вылетала из пинцета в неизвестном направлении,что ее после не найдешь.У меня 2 раза улетали заготовки,а на третий раз все получилось в лучшем виде.Вставил аналог ножки в отверстие рядом с поломанной.Никаких паяльных работ не производил.Поставил процессор,сделал подсоединения к мат.плате и включил питание.Плата сразу заработала,как новая.Температура процессора 25*С,т.е. комнатная. Тут надо сказать,что эту плату мне продал один паршивец-малолетка через Авито.Когда я пришел домой и посмотрел через лупу,то увидел,что штук 10 ножек погнуты,а одна отломана.Я хотел вернуть плату назад продавцу,но он отказался забирать ее назад.Причем при общении с ним в чате Авито выяснилось,что он изначально знал,что ножки согнуты,но при продаже уверял меня,что плата полностью рабочая.Поэтому мне пришлось решать проблему самому.Все ремонтные сервисы у нас в городе отказались делать эту работу. Вот думаю,снять что ли видеоролик про свой ремонт?Или не заморачиваться? Я - обыкновенный пенсионер. ruclips.net/video/Y9GXBJ-vbiM/видео.html
Given that I do not feel responsible for any damage, this is the profile then I use on my Achi ir pro sc R1=1 L1=85 D1=80 R2=1 L2=150 D2=30 R3=0,75 L3=190 D3=30 R4=1 L4=220 D4=35 R5=1 L5=245 D5= 40 Bottom heater 260°c Room temperature 20°c Before starting the program preheat bottom side of motherboard at 70°c In addition to the 2 thermocouples of the reworck station another two or more, one in contact with the motherboard under the socket and the others around the socket in upper side. If you find inconsistencies between the values around the socket, make the operation abort.
please tell me in a list of what u used to make this all happen, what bench did u use, what flux, and ironer, please fill in, waqnting to do this as well just no equiptment and need ideas Thanks
Rework station Achi ir pro sc Aluminum adhesive tape Flux Amtech rma 223 for desoldering (Because I do not feel well when welding probably because it is not original) Flux Kingbo rma 218 for soldering Economic soldering irion modified in the tip Desoldering braid techspray 1825-5f Microscope supereyes b008 Fluke 2166a 10 channel thermometer with Type K Thermocouple Isopropyl alcohol for clean A lot of patience, a lot of practice and a lots of tests to find the right profile.
I was wondering if this will fix my motherboard instability or is my motherboard gone at this point. I can easily get a 1151 replacement socket for much cheaper than a brand new assembly aka motherboard.
Hello excellent video do you think you can do that work on my motherboard 1155 asuss p8p67 delux I need help I spend a lot of money and mistakenly damaged it
Ai ragione è una operazione molto delicata io sono uno di quelli che o rovinato un scheda madre msi modello Z270 GAMING M7 e scusa che mi permetto e anche un lavoro che deve costare se riesci a portare a termine meglio tentare se va male si usa per museo meglio lasciarla conservata che serve scusa il giro di parole cmq complimenti
I'm learning about motherboards online and it is absolutely the worst having an online lab. Everything is so tiny I have NO IDEA where it's supposed to be connected
Perché non spiegate l'apparecchiatura che usate per smontare la presa con le sue caratteristiche corrispondenti tutto in completo silenzio o è che siete muti e pensate che tutti siano così. Dove hai comprato la presa?
It is imposible to reball the socket, i tried lots of times.. its better to buy the socket on the Internet, but in mano countries is difficult to find them
Given that I do not feel responsible for any damage, this is the profile then I use on my Achi ir pro sc R1=1 L1=85 D1=80 R2=1 L2=150 D2=30 R3=0,75 L3=190 D3=30 R4=1 L4=220 D4=35 R5=1 L5=245 D5= 40 Bottom heater 260°c Room temperature 20°c Before starting the program preheat bottom side of motherboard at 70°c In addition to the 2 thermocouples of the reworck station another two or more, one in contact with the motherboard under the socket and the others around the socket in upper side. If you find inconsistencies between the values around the socket, make the operation abort.
Por como se veían los pines del socket, ya no tenia arreglo, mas que hacerle esto. El tema es que en todos los videos, nadie prueba la placa con algún procesador.
@Julinho Millones pero de qué funciona, funciona. Aunque no se si en todos los casos. Viendo tutoriales es posible hacer un buen trabajo, y rescatar una placa.
The price of the Motherboard socket is the same as the price of a 2nd hand good condition 1155 motherboard, why not just buy a used 1155 motherboard instead? This process takes time and money and has a chance of 50/50 not to work if the solder is wrong,
I think because it’s harder than it looks and a lot of the time it will stay broken lol I’ve got a removal video I haven’t got round to uploading the second part as it was a fail lol I heated the new socket to much and melted it I then panicked and pulled it back off and damaged a couple of pads so I’ve got to re look at it lol
This is the damn fucking reason I hate Intel. Like why couldn't they opt for AMD like contacts. It's much more durable and not likely to get bent when being worked on.
![[LGA1151] ¡Reemplazo exitoso del zócalo de la CPU! reemplazo de socket de cpu [junk PC]](http://i.ytimg.com/vi/Z4o88JnhP-0/mqdefault.jpg)
5:33 dude you're a frigging hero! I went to pick mine up with the tweezers and ended up pushing the socket sideways which cause the golden contacts in the center slide off haha
To anyone attempting this, be extremely careful to lift it upright
I have the same motherboard,it had like 50 pins bented ,i got them on correct position,it works like a charm (it took me like an hour )
Are you studying for a brain surgeon?
Congrats on saved mbo!
@@RTCLR123 thanks :D, no no ,i don`t even have the most steady hand :P
@@adrian8121 I have 2 or 3 missing pins and it won't post.
@@jp2650 it`s nothing you can do, replace motherboard
@@jp2650 replace socket
Урррраааа!!!Получилось!!!!Отремонтировал поломанную ножку в сокете,хотя у меня нет специального оборудования и запасных ножек на замену.Взял подходящую заготовку и при помощи надфиля вручную выпилил аналог ножки.Тут главное - не допускать,чтобы обрабатываемая заготовка не вылетала из пинцета в неизвестном направлении,что ее после не найдешь.У меня 2 раза улетали заготовки,а на третий раз все получилось в лучшем виде.Вставил аналог ножки в отверстие рядом с поломанной.Никаких паяльных работ не производил.Поставил процессор,сделал подсоединения к мат.плате и включил питание.Плата сразу заработала,как новая.Температура процессора 25*С,т.е. комнатная.
Тут надо сказать,что эту плату мне продал один паршивец-малолетка через Авито.Когда я пришел домой и посмотрел через лупу,то увидел,что штук 10 ножек погнуты,а одна отломана.Я хотел вернуть плату назад продавцу,но он отказался забирать ее назад.Причем при общении с ним в чате Авито выяснилось,что он изначально знал,что ножки согнуты,но при продаже уверял меня,что плата полностью рабочая.Поэтому мне пришлось решать проблему самому.Все ремонтные сервисы у нас в городе отказались делать эту работу.
Вот думаю,снять что ли видеоролик про свой ремонт?Или не заморачиваться?
Я - обыкновенный пенсионер.
ruclips.net/video/Y9GXBJ-vbiM/видео.html
after replacement, is the motherboard are running?
That is one effed up socket and gutsy repair by you
You're an hero
Nice & smooth...
Awesome...
Excelente video, imprescindible al menos para mi. Ah! y gracias por no poner música, muchas gracias por eso. k.anton.Arg.
How much to replacement a 1151 socket ? Would you do repairs?
How long did you heat the socket for and at what temperature?
Given that I do not feel responsible for any damage, this is the profile then I use on my Achi ir pro sc
R1=1 L1=85 D1=80
R2=1 L2=150 D2=30
R3=0,75 L3=190 D3=30
R4=1 L4=220 D4=35
R5=1 L5=245 D5= 40
Bottom heater 260°c
Room temperature 20°c
Before starting the program preheat bottom side of motherboard at 70°c
In addition to the 2 thermocouples of the reworck station another two or more,
one in contact with the motherboard under the socket and the others around the socket in upper side.
If you find inconsistencies between the values around the socket, make the operation abort.
Are you heating both sides of the MB or just the bottom?
Just the superior side, i think.
what work station are you using to remove the socket?
IR6500 IR BGA or similar..
Hi, can u write down what i need All for This project? Thanks
Where did you get the spare part?
I think you can search them in aliExpress or ebay
@@mohammadhafiz4202 con que nombre
please tell me in a list of what u used to make this all happen, what bench did u use, what flux, and ironer, please fill in, waqnting to do this as well just no equiptment and need ideas
Thanks
Rework station Achi ir pro sc
Aluminum adhesive tape
Flux Amtech rma 223 for desoldering (Because I do not feel well when welding probably because it is not original)
Flux Kingbo rma 218 for soldering
Economic soldering irion modified in the tip
Desoldering braid techspray 1825-5f
Microscope supereyes b008
Fluke 2166a 10 channel thermometer with Type K Thermocouple
Isopropyl alcohol for clean
A lot of patience, a lot of practice and a lots of tests to find the right profile.
I was wondering if this will fix my motherboard instability or is my motherboard gone at this point. I can easily get a 1151 replacement socket for much cheaper than a brand new assembly aka motherboard.
Please repair my socket. And what is the charge
Can I know all items u use to replace new socket
What would you charge to replace a 1150 socket ?
Hello excellent video do you think you can do that work on my motherboard 1155 asuss p8p67 delux I need help I spend a lot of money and mistakenly damaged it
Salve e buon anno. E' per caso disponibile per fare un lavoro del genere anche a terzi o lo fa solo per se stesso?
Ciao, non lo faccio perchè è un operazione molto delicata e non sempre il risultato è quello sperato. Buon anno anche a te.
Ai ragione è una operazione molto delicata io sono uno di quelli che o rovinato un scheda madre msi modello Z270 GAMING M7 e scusa che mi permetto e anche un lavoro che deve costare se riesci a portare a termine meglio tentare se va male si usa per museo meglio lasciarla conservata che serve scusa il giro di parole cmq complimenti
I'm learning about motherboards online and it is absolutely the worst having an online lab. Everything is so tiny I have NO IDEA where it's supposed to be connected
Could you tell me please what temperature was your solderinf iron when you clean the pads from the solder?
Hello sir
Mere bhi same board hai 1155 same problem hai pins damage hogaye hain.
Mai bhi pins socket change karwana chahta hon
Mera bhi 1155 he mebhi change karna chahta hu
Perché non spiegate l'apparecchiatura che usate per smontare la presa con le sue caratteristiche corrispondenti tutto in completo silenzio o è che siete muti e pensate che tutti siano così.
Dove hai comprato la presa?
Now turn the computer on with the new socket and show us that it works. Electronics require the upmost precision in order to operate correctly.
not really
basically it's a reballing, nothing crazy about it, it should work fine after cooling and putting the cpu back into the socket
I want to buy that socket so plz provide me link to buy
Bhai kaha ripear ho raha hai
How long will it take? Just couple hours? Because I have my motherboard still on technician for a week now
Can they fix broken pins
@@egarun23 They can, my motherboard work fine now
@@GentleGazer162 Can you give their contact info.
Hello, could you tell me where and how is it called to achieve what they desoldered where the proccessor is placed and did it work for you?
Salut à combien chauffes tu?
Perfecto
Brother, where are these sockets available?
www.ebay.it/itm/Foxconn-Intel-Socket-ProcessorCPU-Base-ConnectorHolder-LGA1151-1150-1155-1156-BH/113690566654?_trkparms=aid%3D111001%26algo%3DREC.SEED%26ao%3D1%26asc%3D20140423084956%26meid%3D0f6b5ecae06647c7964723c9d9859f24%26pid%3D100033%26rk%3D1%26rkt%3D8%26sd%3D183668430255%26itm%3D113690566654&_trksid=p2045573.c100033.m2042
How to buy the socket ????
Amazon
Great
Que son esas puntas que le colocaste para calentar... No se ve fácil el asunto, explica. Eres mudo o que, no se escucha ni siquiera un pajarito
Can you please tell me where did you buy the new cpu socket??
it.aliexpress.com/item/LGA-1150-1151-1155-1156-2011-2011-3-775-1366-4788-AM3B-FM2-Motherboard-Mainboard-Soldering/32815422273.html?aff_platform=default&cpt=1529995808167&sk=cka1gvPK&aff_trace_key=77a8daad2a194e7c84d8ed9ac22a6b6e-1529995808167-07663-cka1gvPK&terminal_id=5f32413d5d634b2e92d444609de645db
No Test???
It is imposible to reball the socket, i tried lots of times.. its better to buy the socket on the Internet, but in mano countries is difficult to find them
I have 2 or 3 missing pins and it won't post.
can you tell me your plase...?
81 motherbord processor pin broken plz help me.
how can i buy this bro
Como puedo conseguir una
En Aliexpress venden los socket. Cuestan actualmente unos 4 dolares.
las instrucciones ? Como hacerlo , que temperatura o corriente ?Que productos ? gracias
Given that I do not feel responsible for any damage, this is the profile then I use on my Achi ir pro sc
R1=1 L1=85 D1=80
R2=1 L2=150 D2=30
R3=0,75 L3=190 D3=30
R4=1 L4=220 D4=35
R5=1 L5=245 D5= 40
Bottom heater 260°c
Room temperature 20°c
Before starting the program preheat bottom side of motherboard at 70°c
In addition to the 2 thermocouples of the reworck station another two or more,
one in contact with the motherboard under the socket and the others around the socket in upper side.
If you find inconsistencies between the values around the socket, make the operation abort.
Por como se veían los pines del socket, ya no tenia arreglo, mas que hacerle esto. El tema es que en todos los videos, nadie prueba la placa con algún procesador.
@Julinho Millones si funciona, eh visto otros vídeos y si les funcionó. El tema es sacar el socket antiguo, es un trabajo un poco más técnico.
@Julinho Millones pero de qué funciona, funciona. Aunque no se si en todos los casos. Viendo tutoriales es posible hacer un buen trabajo, y rescatar una placa.
What materials did he use?
Flux and copper
Four words; Life Is Too Short.
same problem, please help.
What kind of liquid-dry did you put?
The price of the Motherboard socket is the same as the price of a 2nd hand good condition 1155 motherboard, why not just buy a used 1155 motherboard instead? This process takes time and money and has a chance of 50/50 not to work if the solder is wrong,
Sockets are like 5usd
Link of the socket pins
Who can help me my motherboard and do the same thing to my motherboard cpu socket are damaged
Good but incomplete.
sr 775 sockt chahiya mujhe plz help me
is it working
No, the card did not work for another reason, the socket was damaged to make the video.
@@satu5193 I like your honesty sir.
What is the cost of replacing?can we change the socket 478 to775?
1: the socket will cost 6 dollars, unless you do not have the tools. 2: no, it won't work.
what you charge to replace lga1150 socket?
Aliexpress buy a socket, $4 dollars.
Can you send the link or the model of your heat machine? please
এটা কোন জায়গা ভাই আপনার ফোন নাম্বার টা দিতে পারবেন
Para reparar mi placa
Me pueden ayudar
Hi, can you change it on mine mainboard ?
Why do everyone who does this never try it out here in the video with a cpu just saying
I think because it’s harder than it looks and a lot of the time it will stay broken lol I’ve got a removal video I haven’t got round to uploading the second part as it was a fail lol I heated the new socket to much and melted it I then panicked and pulled it back off and damaged a couple of pads so I’ve got to re look at it lol
Can you please share te profile ?
Its always a gigabyte
can you do the same thing with my motherboard it needs a new socket its a sabertooth x79 with socket 2011
ভাই আমার ইসোনিক মাদারবোর্ড ডিসপ্লে আসেনা ভিডিও কলের মাধ্যমে সমাধান দিলে ভালো হতো
ভাই আপনাদের একটা নাম্বার দেন
এইটা কন জাই গা
Please help me sir
Mine is way worse it's like a dragon flew into it
This is the damn fucking reason I hate Intel. Like why couldn't they opt for AMD like contacts. It's much more durable and not likely to get bent when being worked on.
Satufék xD