Good vid, lots of good tips. My 2017 grizz chews threw break pads.. put ebc pads on all 4 corners at over $200 can. Lasted 6 months 1000km and they were gone again and I don't use my breaks much. Cheap 1s on line last longer and u can do all for corners for $40. I usually do my diffs when I do my oil. Keep them the same easier to remember when you to do next. Lol 🤙🍻
Just installed a 20” lightbar on my 2014 grizzly 700. Last winter I put on heat demons hand grips and thumb warmer to go with my 60” kfi plow setup and vrx3500 warn winch. Gotta get some iron Baltic skid plates next and some storage boxes.
I do mechanic work and overtime with never sees it hardens up after a while and you'll be back to stage one again I noticed it the last couple of years cuz I always use the stuff I switched to the copper it doesn't dry out and doesn't get hard so try to copper nice bike by the way
The Renegade has a single brake lever as well. I miss my Grizzly with the two brake levers. But one thing I do like is the brake lock. Which yamaha doesn't have.
I’d love to get my old 06 Rhino going again but it needs a motor and transmission, I broke the gears in the transmission which back in 2011 was gonna be $3500 so I decided to get a CanAm Commander because I was in need of something for work.
The gear selector on my 23 can be stubborn I noticed others complaining also but some people say theirs is smooth Is there something I can do to make it smoother
Excellent tips on the grizzly brakes! Do you use anti-sieze on the threads of those hex pins that hold the pads in? I have a 2014 that needs pads...hoping I can get those pins out without issue.
@@LAUDROffroad Well, dangit, I guess I'll find out in 5-10 years when I put new brake pads on mine. My 14 threads were super clean. Could not believe it. I added anti sieze when reassembling. replaced brake fluid while I had it apart and used EBC severe duty pads. Stops better than stock now!
@@SCOTIAN_ Did suspect not donate a tool to save the polaris time and time again, pull the swamped can am out. she puts in the work to keep everyone else moving! hahahahahaha
Hey I have a 2016 yamaha grizzly 700 and j was riding one day and when I home there was coolant leaking out one of the little tubes from the snorkels but there was no over heating light turned on anyone know what that can be?
If they weep hole breather was also routed from the bottom of the water pump that is the hose. That is an indicator that your water pump is on its way out or shot, need to be replaced
I would rather have a Yamaha what you have over an XMR 1000 Yamaha is a better respective machine and it's reliable safe trail riding out there be safe
Questions I have a 2022 570 xt outlander and for the $10k answer is it a 650 detuned or just a 570. The sticker under the seat says 650 engine family but says displacement 570.
Show your support with the "Thanks" or "Join" buttons or simply by smashing that like button!
Very informative for a lot of rookies or riders that want to safe some coin because there is nothing more expensive then shop time!!
Great video Drake. The brake pedal on my Grizzly is sticking. Now (Thanks to you) I know how to fix it.
Glad I could Help!! Thanks for Watching!
Good vid, lots of good tips. My 2017 grizz chews threw break pads.. put ebc pads on all 4 corners at over $200 can. Lasted 6 months 1000km and they were gone again and I don't use my breaks much. Cheap 1s on line last longer and u can do all for corners for $40. I usually do my diffs when I do my oil. Keep them the same easier to remember when you to do next. Lol 🤙🍻
Good info & nicely explained!
Thanx for sharin'!
Thank you for watching!!
Good video thanks bud 🇨🇦👍🏻
Thanks for watching 👍
Just installed a 20” lightbar on my 2014 grizzly 700. Last winter I put on heat demons hand grips and thumb warmer to go with my 60” kfi plow setup and vrx3500 warn winch. Gotta get some iron Baltic skid plates next and some storage boxes.
Yesss brake tips. I’ve had brake issues since I bought the thing and I bled each side with a mighty vac
Grizzly rule- I have 2008 and 2020 -700 Kodiak- thanks always work
We loved the yamahas we have had in the past! Thanks for watching
I do mechanic work and overtime with never sees it hardens up after a while and you'll be back to stage one again I noticed it the last couple of years cuz I always use the stuff I switched to the copper it doesn't dry out and doesn't get hard so try to copper nice bike by the way
The Renegade has a single brake lever as well. I miss my Grizzly with the two brake levers.
But one thing I do like is the brake lock. Which yamaha doesn't have.
Yeah it was the same for my Outlander. At one point this wasn't the case for CanAm but they decided it wasn't necessarily useful.
Just so you know, Yamaha calls for only 40 ft/lbs on the lug nuts not 75. I have a 2018 Grizz 700 and I don’t do more than 50
Great tips thanks for sharing..
Thanks for watching!
Polaris has the rear only foot brake too. And yeah, I do miss my KQ's separate front/rear brake control.
Happy birthday!
Thank you!👍
Drill and tap that break pedal for grease fitting there room for it
I was going to say that
I’d love to get my old 06 Rhino going again but it needs a motor and transmission, I broke the gears in the transmission which back in 2011 was gonna be $3500 so I decided to get a CanAm Commander because I was in need of something for work.
Why replace the motor is the trans is all that broke?
@@christopherbassit2757 well it hasn’t ran in over 10 years so I figure it will need a rebuild or something
I love the Line X paint job on the plastics. Did you have them professionally done or DIY? Thanks.
The gear selector on my 23 can be stubborn
I noticed others complaining also but some people say theirs is smooth Is there something I can do to make it smoother
Excellent tips on the grizzly brakes! Do you use anti-sieze on the threads of those hex pins that hold the pads in? I have a 2014 that needs pads...hoping I can get those pins out without issue.
I do not. Antiseize/grease etc, in dusty conditions actually attracts and holds dirt and moisture. Clean and dry is your best friend
@@LAUDROffroad Well, dangit, I guess I'll find out in 5-10 years when I put new brake pads on mine. My 14 threads were super clean. Could not believe it. I added anti sieze when reassembling. replaced brake fluid while I had it apart and used EBC severe duty pads. Stops better than stock now!
Drake did a good job explaining every out. I didn’t know he had to do maintenance when you don’t ride it 🫣. Lol 😂 I’m joking
Poor bastards been slaving and not riding. Ratios all wrong!
@@MainvilleATV lol 😂 …..needs to take that to the Nesbit skeg field to get it dirty .
@@SCOTIAN_ Easy Now!
@@drakemath 😂
@@SCOTIAN_ Did suspect not donate a tool to save the polaris time and time again, pull the swamped can am out. she puts in the work to keep everyone else moving! hahahahahaha
what brand of tires are those and do you use stock wheels
Hi Great video I have YAMAHA grizzly you should look at Racedriven mud rotors I have them on my atv and dont go through pads as bad.
Awesome, I'll have a look 😀
I will definitely have to look into those! I've tried before with no luck! Now I have a brand! Thank you!
Thanks for video. My brand new 2022 grizzly 700 is missing the little plug on one side. Where can I find one? R you know the part number. Thanks
Hey I have a 2016 yamaha grizzly 700 and j was riding one day and when I home there was coolant leaking out one of the little tubes from the snorkels but there was no over heating light turned on anyone know what that can be?
If they weep hole breather was also routed from the bottom of the water pump that is the hose. That is an indicator that your water pump is on its way out or shot, need to be replaced
Is this the original colour or simple black paint. Is there primer under the black colour?
Original colour, no primer. Just linex from what I understand.
THX a lot
What kind of bumper did you have
That's a yamaha bumper.
I would rather have a Yamaha what you have over an XMR 1000 Yamaha is a better respective machine and it's reliable safe trail riding out there be safe
Questions I have a 2022 570 xt outlander and for the $10k answer is it a 650 detuned or just a 570. The sticker under the seat says 650 engine family but says displacement 570.
No, different top ends. They are different, just enough.
You linex your how
Why would you puts whips on it ?
There are a number of event we go to that they are mandatory, riding a quad around monster trucks. Safety first
What headlights you running
Oem with far mudding halos from dirtylife.ca
What tires are you running?
STI Out and Back. 28x9x14
I need you.
Yam.a.ha
Vs
Ya.ma.ha
I'm a "yah mah hah" guy myself.