Instructions Calculate and Wind Mosfet Gate Driver Transformer ( GDT) | Without Using Any Software

[@rkelectronicsbd1218]

This is helpfull
Thank you sir
From Bangladesh ❤️

[@LongTechnical]

Thank bro

[@ministeriomundialliberando8403]

I have a question: in the video you show a push-pull topology, if this is case you need two primary whereas you are using only one, what's the reason? Thank you in advance.

[@rafalg.6901]

Are you calculating for 15V peak-to-peak AC or 15V DC square wave? There should be at least 15-20Vpp (30-40V DC), or more (some bigger transistors accept +-30V) for the best performance. Higher gate voltage = lower output resistance and heat loses.

[@kostadinparaflow1429]

I noticed that when you test, you put some capacitors, and I don't put them, if this is the reason, if so, how do you connect them and what is their value.

[@republicoftutorials6068]

Thank you so much it helped millions

[@LongTechnical]

OK bro

[@selimdumlu4519]

I can not take this osc wave - picture I see only sharp pulses My signal is 200 Hz You use some caps at the signal ends , which value are there ? please explain it

[@ansssaja7721]

I don't skip ads sir 😁

[@anditoba4096]

in the calculation of 8 turns, what I see is there are 14-15 turns, how can that be?

[@tunaysezer4089]

+ - 20 volt gate voltage out.

[@electronic7979]

Helpful video

[@LongTechnical]

Thank bro

[@drxfuncaption9322]

How make smps circuit + feedback

[@LongTechnical]

Conenect ouput to feckback pin to control output

[@HiWinchHDTV]

exel file is same ferrite core .. can not dowload toroid core download

[@ajiebae9652]

Thankyou sir... You're the best!!

[@ansssaja7721]

How to wind the SMPS supply transformer for the uc3845 apk module?

[@reza_khaksar]

Thank you sir
From Iran

[@kostadinparaflow1429]

Hello, I need a little help, I wound a transformer driver on an EE 19. With a primary 12v and two secondary 12v with a frequency of 35kHz and I use an SG3525 LM358 Inverter Driver Board 12V-24V problem is that the transistors they start to heat up a lot, which are on the SG3525 LM358 Inverter Driver Board (B772-D882) at the output of the driver transformer as I measure with the oscilloscope everything is perfect and its frequency is 35kHz. If you have Facebook, we can continue communication there if you are not comfortable here. thanks

[@atiyatech]

B772 and D882 can handle upto 5KHz frquency.

[@drxfuncaption9322]

How select mosfet for 2000w 100k hz smps

[@LongTechnical]

Google bro, you need to read datasheet of mosfet example IRF3205

[@dilikash851]

Hello. Dear friend, you can ask file Lay.

[@trananhtu5790]

video rất chi tiết , thank bro

[@LongTechnical]

Thank bro

[@MrRais66]

Great idea sir. Thanks

[@manoftheday1]

God bless you sir, please make excel sheet to calculate (the white on yellow toroid or blue on green toroid at the out put of smps thanks.)

[@LongTechnical]

Thank bro. There core is not for smps

[@manoftheday1]

@@LongTechnical The core i was referring to is the iron powder core.

[@ansssaja7721]

Nice video sir

[@anaspbc9810]

pls how to stun fish inverter pdc

[@Dc_tech386]

What about low frequency hate driver

[@jhoncaldas]

excelente saludos

[@LongTechnical]

Thank bro

[@rodrigowronski]

Tudo bem. Poderia passar o esquema

[@yotsukelhancker]

Exelente tutorial sir en español seria genial

[@LongTechnical]

Thank bro

[@ShakeelAhmed-ft2mx]

Nic projact

[@LongTechnical]

Thank bro

[@freedomisfood6966]

You are my master.but liying is bad five kilowatt????

[@tomg8069]

Core is too big for this use, it shall be arround 1cm diameter, here we have small power just to charge and discharge gates capacity.

[@extremeaudio8975]

Can we use 1cm core ?

[@extremeaudio8975]

And how many turn bro ?

[@hendriagustian7082]

I need help with your answer sir @Long Technical

[@user-tm3wg1uq9c]

god

[@quanghoang04]

👍👍

[@兵马俑闯天下]

给个文件

[@1990daner]

Sg3524

[@LongTechnical]

Sg3525 bro

[@1990daner]

@@LongTechnical no sg3524 power inverter please