BIG BORE Kit Installed on 47cc 49cc Engine! Every Step Included
HTML-код
- Опубликовано: 14 янв 2025
- Big Bore Kit (Ebay): rover.ebay.com...
Big Bore Kit (Amazon): amzn.to/2KV4WVz
Thanks for stopping by my channel!
Patron: / dylondesbiens
Business inquiries: dylon.desbiens@yahoo.com
Fun factz I just installed this engine in a new drift trike build for kids!! Check out the new build on it I just uploaded :)
Hey Dylon were you one that recommended getting the KTM carburetor for your 50cc pit bike with the performance egine? If so I was just wondering what jetting sizes you used because I finally got mine up and running and it runs kind of crappy. You helped me with a couple of other things with the bike last year. Thanks in advance.
When are you going to give us some new videos all what I have watched is 2 yrs old
I always found the "Black Widow" reeds the best for a high-performance build and for the head, you should use a performance head where you can adjust your "squish" settings (the amount of space at TDC as you can change your compression) and get that maximum performance, 2 shoe clutch with adjustable springs, various gearing and the possibilities are endless.
The top end speed I managed to get out of my 49cc lucky 7 was 74mph
how 74mph?
don't worry about the baring my dad works on all kinds of stuff like that and he had the same problem but he tried it and it worked and we still use it today and we put the ket in one year ago so it will be fine
I noticed the stock bearing is actually shown in the listing picture, so I guess they sent me the wrong one. I haven't heard back yet tho.
yeah I hope they send you the right one this time
and can you plz help me grow my RUclips channel
If the bearing has that much movement in between the rod the engine will blow up instantly. The bearing will likely break apart and seize the bottom and top end after all the little needles get stuck inbetween them.
The piston will expand slightly once the engine is warmed up. That's why it's 43.9mm and not 44mm. If it's 44mm when cold then the clearance between the piston and the cylinder will be too small/tight once warmed up which could cease the motor
When installing your rings always one Groove at a time, less chance of breaking a ring
so bad when someone wanna show for noobies how to do it in wrong way...
in our country if you buy order big bore kit, it will came with new performance crankshaft and you will not have these type of problems (and engine will rev even more because the crankshaft will handle it, i think about 2000rpm more, i didnt test it yet..)
use 2stroke oil, that is good advice (you can read why up in these coments)
I think you didnt use the cylinder gasket (between cylinder and crankcase) so check it because without this gasket your engine will not start up...
the window in piston is for the third transfer port in your new cylinder ;) (you will get more mixture into your cylinder) and no that window is not weight reduction :D :D because some people will think it...
carbon reed valves - awsome thing, I love this thing, you will have large increase in accerelation
rocket key - it is very good thing, you will increase accrelation, power in HP and top speed little bit, but something is still mising there... your flywheel is heavy, so I recommend you to buy performance flywheel instead, it is lightweight and you must not use rocket key because timing is changed in factory (if you cant find it, just type in google "tuningovy zotrvačnik minibike" and you will find some photos of that)
carburetor - the stock one is carb with float, performance carb that you used (that on the photo) is also float type, but it have 15mm bore what is much better compare to stock 12mm, but it is china style and lot of people have trouble with them... the last one witch you are preparing for your engine is 15mm too but it is another typ, it is membrane carb, this type of carbs you can find in chainsaw, weedeater and stuff like that, it is much better because this carbs dont have issues with mixture even if they are upside down... but please study how they works and how to mount them before you start... I personaly dont test them yet so I cant tell you about performance but if you set good mixture (with set screw on carb) it will be fine and I think you will have better performance than from the stock one :D just pay attention on mixture otherwise you can kill the engine ...
exhaust - I didnt see any exhaust in the videos, why ? without exhaust you will loose all performance... and you can even kill the engine if you run it long and in high RPM... and again you will lose lot of your performance, engine will not be able to rev more than 8KRPM i thing... in 2 strokes all performance is depending on your exhaust... the stock exhaust will perform better than nothing, yes with or without exhaust this engine will be very loud, but with the exhaust you will have power too ...
dyno - only way that I know right now is (also it is cheap and you can do it easily): use big eletric motor as generator, than start pluging some bulbs (high power) and plug them one by one until they start going out, just little bit, and use multimeters to mesure current and voltge, by multipling it you will get power in W (you will need at least halogen lamps because stock pocketbike have around 2kW that is 2000W) if you want know the horsepower you just simply multiply performance in kW by 1,3 and you will get your horsepower... but remeber it is not exactly perfect mesuring so you will lose about 10-30% by conversion to electricity, multimiters are not allways perfect (so readings may be different) power loos in cables and stuff like that, but it should work just fine for small tests and maybe you will use it as generator in blackout so maybe it will worth it :D :D :D
Wow thanks for taking all the time for this. Awesome... I was going to do the user suggested "rip some of the fins off the flywheel" But I think I will go your route and get the performance wheel. For the exhaust pipe, its shown at 12:06 / I might not fully understand your dyno Idea so I will read that over a few times and talk to smart friends about it :D Thanks !! Carb tests coming soon too / Edit And yea the gasket is there just hard to see, I didn't change gaskets or remove any
David Baran WOW man you know alot what if my engine is knocking or my carb is leaking do i need to replace
Jeibaru Turay if your carb is leaking, the float is probably stuck, so you should clean your carburetor. If its knocking you need a bigger gasket to get a little less compression or you can use higher octane fuel. I recommend to get higher octane fuel before you buy a new gasket
I like your dyno idea! Sounds great
Sorry for my bad english :D I was in hurry, so I don't have time to check what I have writen... Dylon sorry, I missed the scene with exhaust first time, my bad :D
This exhaust shoud work great.
Carburetor leaking, I don't know if you mean air leaking or fuel leaking, so if you have air leake you must change all gaskets + check your reed valves (just take them and look against light, it's not perfect but it works, or simply take them and try suck air throught them, that is better working, personaly I always use second metod, and I always try blow/suck/blow/suck if they are closing properly)
But if you have fuel leaking, start by changing fuel hose (use hose clamps) than dissassemble carb and clean him. I don't know wich carb you using so I will tell you what you should do with stock one (I whould like to make a video for you but I dont have a stock carb right now, only the performance carb...) so if cleaning don't help you, than again dissasemble carb, now just put the bottom bowl down, check float valve, if it works fine, you have the biggest challange - set the float level by bending fork. But remeber changing float level also change mixture ratio !!! Low level you will have lean, high level you will have rich, you must find the ideal for your engine (every engine is special, 2 engine with same settings of mixture doesn't exist)
For a knocking, please specify wich type of engine you are using, but I think it cloud be also damaged engine, so check your compression...
If you look around, you can find kits that are similar to this one, but they have 2-3 boost ports with the main transfers separated, which makes 4 transfers instead of 2 (6 or 7 transfer ports in total counting boost ports).
Could you link?
@@-lig3-852agreed
These kits should come with preinstalled rings on piston
It's so easy to put them on, it's way harder on my dirt bike you can't use a tang
Fr they are a bitch to get on without breaking I had to order new rings because of that
That would defeat the purpose of a project bike man #homebuilt
Why they need to be off to gap them correctly
It’s so easy to put them on, probably shouldn’t work on them if you can’t do that.
For the stock bearing and the movement left and right in the piston skirt it won't matter. The connecting rod only moves up and down in a piston. Never left to right. If it does then that means the piston is to small for the cylinder. Hope that settles your nerves a bit
Thanks your correct but I showed it sorta bad in this, I'm more worry the bearing on its own will roll a lot either on the left side or the ride side while the piston is of course centered. causing some bad wear over time or something fatal to happen on a bump or what ever the elements bring out when riding. But now I see they show the stock bearing in the listing image... So Some mistake was made by this seller. Waiting to hear back.
Life hack for putting on a cylinder put a piece of wood behind the piston
Good idea
Why?
FYI put the piston in the cylinder just past the rings leaving enough room for the rod before you attach. Much easier.
Also if you split the case before the head , the piston won’t hang
Performance Piston Rings actually mostly are thinner for lower friction -> thus more power
Piston rings will not stretch out as you say .I've installed piston rings in an all kinds of engines for many years including ones like this and you can stretch them out enough to get them to go along they make a tool for it yes sometimes they break either way..
Also, it's easier to instal the bottom piston ring in the top groove first, then move it to the bottom to avoid stretching it as much as possible, then install the top ring in the top groove.
Does the big bore kit really make a difference in power or top speed?
I love those little carb kits
You can make a small engine dyno. An inertia dyno would probably be easiest and reasonably accurate for your purpose. I would make it where you could add and remove weights to allow to test on different engines and get several seconds of run time so it doesnt rev to quick but doesnt bog the engine. I believe there is a guy on RUclips that made one his channel was twostrokestuffing I believe. If you need any more help I can try my best to help
Also those carbys need a different fuel tank, but when u have them all tuned up they run way better then stock just takes a little to get the bike started
Yayyy you got the parts i suggested😋
Do you know a place I can get a kit for a 110cc
This video helped me with my install. Thank you!
Just make sure you heat cycle it a few times for the break in
Bruh I’m dead, it’s a 49cc wan gone you don’t gotta do thay
@@03_Kx100 any engine and I repeat any engine needs a break in.peroid......
@@03_Kx100 i doesn't matter how big the engine is you still should do heat cycles
@@03_Kx100 in English?..
What do you have to do
1:09 *EGINE*
Lmao I peep bro bro
Egine
😂😂
I didn't see you install a base gasket. Maybe I missed that part of the video... Also the first carb wasn't a high performance piece. If it has a rotating drum with a hole in it, then don't bother with it. A 15mm Walbro pumper carb (or cheaper clone) would be my suggestion. Defiantly make sure the crank is a full circle type and install a V-block reed valve. I wouldn't worry about the wrist pin bearing. The same thing happened with my big bore kit on my X-1. Do not install an electric starter. Also get the right NGK plug. I hoped this helped some,
Just wondering when that electric starter review will come out
Haha fr
I know this video is old but for future reference you take the chance of warping your crankshaft with no load on brake in
Nice beginnings to a potentially killer engine
If you are going to make a engine run stand it will be fine if u want to be on the safe side take the clutch out , with that carby the fuel tank u need has a 2 lines coming from the tank
Make sure u run high octane fuel with that rocket key aswell
I wanna hear that engine roaring with new performance carburetor
I would have used the kit gaskets because they might have a different thickness which can change compression
I ran into the weirdest issue. I bought one of these kits for my 49cc engine. But when it came to installing the piston i found that the new piston had a much larger pin and bearing. They don't fit into the slot in the crankshaft. Sadly i cant do what you did and use the old bearing as the sizes between the old and new bearing and shaft parts are in compatible. Not sure what to do really... other than that, the piston itself and the new cylinder are the correct parts. Just not sure why the new piston has a larger pin and bearing when compared to the stock version
Try watching the video sometime, smh.
Give this video a LIKE for me!!
What are your thoughts on this?
I Did that several years ago it feel really good, keep up nice videos!
From what I know. Don't run it out of oil, if 2stroke mix it if the oil is injection make shure it is full
Try to do stunts
Dylon Desbiens was 2cc's necessary
Dylon Desbiens For the stock bearing and the movement left and right in the piston skirt, it won't matter. The connecting rod only moves up and down in a piston. Never left to right. If it does then that means the piston is to small for the cylinder. Hope that settles your nerves a bit
Probably do the expansion chamber next and try putting a smaller stinger on it
He probably doesn't even know what a stinger is 😂😂
You should use a ring install tool which puts less Stress on the rings when you install them.
Exactly.for newbies...
To everybody that want's to do this: If your Engine doesn't turn over on the First start try to remove the Sparkplug and turn it over Fast a couple of times, it could be that you just put to much oil into the Cylinder.
If you put the clips in the piston use a cloth and put it in ur engine because the clip can fly away and end up in your engine....
And for installing the piston in the cilinder its much easyer to put the piston in the cilinder before you put the piston on the crankshaft.
Looks like a cool small boxer engine it's clay and even at the sides
You should get what they say you get *keeps extra parts* *complains on off brand spark plug*
So? They sent it, sounds like their problem. Returning it costs time and gas and effort. They should just send the right part.
Side to side movement not so much a concern but up and down that would be fun fact your fingers can feel up to a thousands of an inch
Why didn't you use oil earlier when you put the rings on the piston etc?
Are all the pocket bike engines interchangeable?
The Boy Wen yeah
It is so apparent, that you dont have deep knowledge about how engines actually work and how they are serviced. Thanks for showing the process, but apart from seeing it, there is almost no take-away.
exactly
Thank you, I like your videos mate.
Is there any reason I shouldn't use spacers to raise my 49cc motor in the frame of a Chinese pocket Bike to give the chain clearance on the (non Swinging) swing arm? At the moment the wheel sprocket, pinion, wheels & chain are perfectly aligned so I don't want to go messing with wheel spacers to gain clearance that way.
But if I was to space the motor 5mm upward I could still keep everything aligned as it is now. It would be simple to adjust the top motor bracket & exhaust bracket to fit the lift and the tank would still clear the expansion chamber. Couldn't find any info on Google anywhere so some constructive views on the subject would be good. Thanks
How does this performed? I made a RC car with that engine and would like to improve it!
Did you have more issues with gaskets and piston head hitting?
Wondering if the kits worth it
The engine mount plate needs bracing to handle the stock engine. Considering the flimsy design, first. A yamaha or suzuki jr50 engine, would tear this frame up, quickly. I have one to brace up, for friends, at this time. These mini bikes are, barely, there. Durability is built into nothing on these syxmoto machines. We can do our best to get a summer or two of riding with these.
Old vid but thy still make thsse engines i bought one when theybwere like 65$ cuz i love 2 stroke projects. Lost the carb never did anythibg with it. Now i see they still sell for almost 200$ now was thinking of buying another for a new project so i have extra parts too, so i csn try a port and polish of the heads an d other stuff. Cant many vids about the oerformance, i was sold on the "high compression head" clsimed to go to 11k rpm but always doubted tht claim. Would love to see and know the pweformance
New carb could be bigger to handle delivery of fuel the big bore kit now wants
Its 2cc more
after you give the breakin, give full throttle if you don't hear a grinchi sound is good, if you hear any rare sound use another copper gasket on the dome(sound at top speed full throttle)
Two copper gaskets?
Yes is matter of mm MILLIMETERS
then if you like that video I also can do a short video for quick and easy fast trick to install cylinder into the piston (w/rings), so easy videos could be less than a minute
did it crank? where is video of THIS engine running after the BB install?
What is the best pipe you've used for these engines? Did the rocket key make much difference or best leave it as standard ?
You can put the bottom piston ring on the top first then put it in the bottom.
What do you lube the piston and cylinder with? 2 stroke oil or what 😂😅
I saw you get the rod to in the kit
When you got the motor ready to put on , how did you mount it ? I'm using a 4 stroke motor mount on mine and it needs to go to the right about 3 ' . Did you have the same problem ?
can you put a tramission box wit this set up?
LOL at the instalation of the rings....I assure you they wont stretch out lol.....Break yea............HAHA
Of course you can don’t forget about the extension reed valve block with the 4 window reed and a 17,5 carburetor and that’s it
Don’t you need to replace the crankshaft for counterweight? It is heavier now right?
Can this type of engine be mount on a 49cc chinese standup scooter by chance?
What''s the difference between the 47cc and 49cc other than two cc's, why do you prefer the 47cc?, ya might want to think about making a dummy axle with a drum type strap-brake for the engine stand, how else would you ever be able to measure the HP/torque?, btw, they actually sell small engine dyno's on eBay, great video, thanks for sharing.
Why does the clutch look like that normally they have that like covering thing?
Looks good but you really needs a piston ring tool. It will avoid scratching the crap out of the piston....
it will be fine just don't rev the snot out of it use a good oil like klotz R50 mix it rich on oil 25:1 for the frist few tanks then run it at 32:1 mix also use a high octane gas like 91 or better
thebug 404 klots is the best two stroke oil on the market
The motor won’t blow up on the stand but u should attach a chain to a sprocket just to get it used to haveing pressure while running
For a small engine I don't think it will but still an engine is an engine it goes down to the quality of it
Have you used drivven? Compact I/o modules that give the mini diagnostics on par with anything out here. I have an array of sensors and mad knowledge don’t know if you ever got an answer ?
I want to build a faster pocket bike recommend me where I should start
But where did u get the big bore kit
Do you have a link for the pipe? I cannot find it anywhere
So did you ever break the rod arm or bust the barring?
No, nothing bad happened. Engine runs in the new kids trike I recently built in the newer videos.
Hopefully the cylinder holds in place
is this engine
for a pocket bike,
sorry but you didn't
say , so We had to ask.
How long did it last? 😂
Can you just install any 49cc big bore kit
When it’s brand new still not broke in yea I would say it’s bad but break it in an try it then an a Dino set up idk I been looking my self
How many cc's are added with the big bore kit
can this engine be flipped to where the clutch faces down like a vertical drift shaft
Yeah, just get the HP delerto replica carb and turn the carb upright while the engine is sideways
A 2-stroke engine will run in any position as long as a carburetor is up straight unless you use a pumper carburetor
Can you tell us what size piston that is???
Place the piston in the cylinder first then piston on rod
So they have send a other bearing to you?
Frederik Stamm they ended up being very giving about the whole thing when the problem was realized
Hi I've got a 4 wheel electric scooter electric scooter I would like to know if I could fit that sort of end I could fit that sort of engine in it as it doesn't go that fast
Can you use grease
It isnt advisable to gap the rings before installing them?
Probably not necessary with these engines. Its been running fine too.
@@jaguars004 better safe than sorry. They do reach pretty high temperature that can expand them, and if too tight might break the ring. Have you ever considered machining an extra ring groove above the top ring and adding a third ring? That would increase your compression.
No I haven’t may be I could get a head with 3, probably don’t have tools myself
dril small holes in the piston ring grooves so oil can get underneath the ring never loose compression
Do you need to upgrade the carb as well if you go for big bore kit?
You should but it's not needed
Dylan what brand do you suggest for a 50cc 2 stroke engine for an old calgari pocket rocket? I’m currently restoring one thanks dude!
Friend what your crankshaft oil seal size is it 7 15 25
Also yes, it's bad for 2 strokes to be revving it without load becuase it will overheat and possibly blow up sooo I wouldn't do it. Hopefully this thing will rip when done
You are a big inspiration to me I just want you to know that
Hey I was the one with the new 110cc venom pocket bike for sale! You said to hit you up on instagram but I don't have one! What other option do we have for communication? I have it listed on let go and offer up! Let me know! Thanks!
Message me on the Facebook page high performance films red and black profile pic
You should put a turbo on it
What kit is this? And if you may, where did you get it from?
Good work nice video 👌
Where did you get that exhaust from? I’m trying to find one for my little 49cc dirt bike but could only find a stock one
Amazon
For my bike BMX 🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻❤️🙏🏻❤️🙏🏻❤️🙏🏻❤️🙏🏻❤️❤️❤️
i know a std 49cc is about 3 HP....what extra HP is gained plz
hi you are supose to have load on two stroke motors to run in mode for about 2 hrs
This is usually how I put my rings on my Pistons but they have a special tool designed for this
Can u tell me where I can buy same exhaust like yours pal
How much mm piston
hi i have just done the same to my engine i want to see the video with you fitting the electric start what you are doing i am doing the same i am very interested in your videos thank you for every thing well done
I personally would have used a couple of washers to stabilise the budget pin bearing