@@McMasterProGenius Hello dude, i want to make a dual transformer inverter. Can i connect those transformer in parallel? E.g dual 500w to make 1000w inverter. All vid i've found just about rewinding those transformer.
If that epoxy (or the tape) isn't a good enough heat conductor, then that entire heat sink is useless. Better would be drill and tap holes, then screw them down. Easy in Aluminum.
This is cool. One point to note is the durability of irf3205 mosfets on 12v source and inductive load is unreliable. Since there are neither any snubber protection nor schottkey diode in circuit, cant say how many of those mosfets survive.
IRF3205 mosfet 110A and 55V. This mosfet is based on 110 amps. With 50% safety, it resists 50 Amps. 30 of them can give us 30 * 50 = 1500 Amps. For 12 Volts this means 12 * 1500 = 18000 watts. 4 mosfets are sufficient for 2000 watts. Transformer link: 80W AC 220V To 24V Single Low Frequency E Type Isolation Small Power Transformer This circuit does not work. Trasformator is powerless and wrong
Maybe the mosfets are so bad, he has to use so much of them... But this remembers me of an inverter to glow up a fluorescent tube up to 60W from 12V with one mosfet without any heatsink needed for small tubes and a mini ferrite transformator. So the biggest question is the waste of electronics for this. Think of the planet, please!
It's not powerful sir the mosfet very hot and not 2000w,the enamels cable use 1.5mm Not 2000watt only 500w and this inverter using zvs system not efficient. :(
How does the circuit work, without an oscillator? The ferrite transformer is very small and is intended for high frequencies and does not operate at 50/60 Hz
you have the construction diagram and the voltage 50 or 60Hz, and amperage specifications? The transformer that you indicate is 24V input and you are feeding it with 12V
*I used those same Mosfets to repair a failed controller for my electric scooter. It blew up as soon as I hit the power. It was a combination of a bad board design and my laziness to add better insulation. I used 15 IRF 3205s. Pay no mind to the comments. This is interesting for me as I'm disabled and just holding a soldering iron is damned hard. Cheers.*
En realidad pudieras usar casi cualquier Mosfet. Pero los recomendados para inversores de 12 VDC son los que tienen VGS de 10 voltios ya que el transistor entrega toda su potencia a ese valor. Si Ids es pequeña unes muchos Mosfet en paralelo para aumentar la corriente, pero lo recomendable es usar Mosfet con valores altos de Ids para no usar tantos componentes
MOSFETs thinking in this video: Hey folks - he wants us to be an 2k Inverter. Let's generate a sine wave on our own and ignore that we're all wired parallel. Common it's for RUclips - forget the physics for the next 12 minutes.
Lo siento mucho amigo ese disipador no es para esa potencia y se utiliza pasta termica no epoxico...... Espero me entiendas lo que quiero aclarar. Saludos
As a professional SMPS designer i have to ask you , DO YOU REALLY DESPERATELY NEED SUBSCRIBERS AND VIEWS ? First thing first , Ohm's law - let's assume that this , i must confess , visualy interesting design CAN deliver 2KW (in dreams maybe) , how much current will it draw from battery ? Almost 170 Amps from 12V , IF it's efficiency is 100% (impossible). Calculate wire gauge for that current. Second, at high currents it is critical to distribute it across MOSFETS with proper wiring! Even 1cm of wire becomes small inductor and big problem. Third , output voltage regulation and frequency. This is a blocking oscillator that oscilates at free running frequency that depends upon load, battery voltage etc.Output voltage is also very unstable. Then there is cooling that is ridiculous ... I really apreciate any kind of work and it's OK to be creative so thank you for this video. People should be inspired with science BUT please stop making toys and claim that they work as a serious device. This thing can deliver from few , to few tens of Watts at best. Put your effort in real science and wanted success will surely come, including views and income ;) Best luck.
Where is the oscillator???? You can not just feed DC into a transformer.... This is TOTAL B.S on so many levels. And gluing output devices to a heatsink would give very poor heat tranfer.
Saludos amigo...tienes muy buenas ideas... Pero es mejor ser más técnico y mostrar planos del proyecto y además las mediciones con instrumentos....He visto que colocas potencias y no son reales a simple vista.........Espero te guste esta crítica constructiva.......Saludos desde Colombia Medellín. Exitos
If the circuit configuration in the video is practically providing 2000W In real time from a (12V, 8.2Ah battery), (MATHEMATICALLY) it has to be like this:⬇️ 2000W= 12V × XA XA= 2000W/12V X= 166.7A 2000W= 12V × 166.7A −−−−−−−−−−− In this case, we need to extract 166.7A from a (8.2Ah battery) So: 8.2A × 1h= ...... [h=hour] [166.7≈ 8.2 × 20.3] =(8.2 × 20.3)A × (1/20.3)h [(1/20.3)hour= (60min/20.3)= 2.95minute] −−−−−−−−−−− So: If the circuit configuration in the video is really providing 2000W In real time, the battery will last for 2.95 minutes only: 2000W= 12V × 166.7A (for 2.95 minutes only)
Again only mosfets in parallel to support more current. You may use it to drive one of your diy high amp one phase bldc motors but not an ac motor. It s a square wave
can i use 12-0-12 10amp 10000mah 220volt ac step down vertical mount transformer instead of small transformer and can i run refrigirator500w tv 150w and vaccum cleaner1000w at a time
Powerful MOSFETs are pretty poor in this design (a multivibrator). If you look at the current generated with an oscilloscope you'll have a heart attack. Oscillations must be made with low power transistors (or MOSFETs) and the powerful ones are used only for switching. As it is 150 Watt is an absolute maximum of what this thing can deliver, especially continuously.
Well. That will only produce something like a square wave. You might use it to light up a bulb but not to run an ac motor efficiently. Moreover, the output frequency is very high.
Na realidade a Potência maxima real é 1320wats.(se a frequência é alta em relação aos 60hz normal, a potência se compara a 2000 Wats certamente. Isso se...Se tiver corrente suficinte na bateria! 😉😄
![Blox Fruits Dragon Rework Update [Full Stream]](http://i.ytimg.com/vi/EqDAp8udhm0/mqdefault.jpg)
Damn, well, it's just brilliant, gluing hot IRF3205 mosfets on epoxy!!! This is the Nobel Prize!
I couldn't continue watching any more after seeing that..... 🤦
that bulb is under 100w. You could give it a 2000W load by powering a room heater. Cool design nonetheless :)
Same qc
Loosu mental
ruclips.net/video/qj7Rfr9mkSw/видео.html
Yes Cool Design if you wanna die beside it :D, It wont last long
How it's possible without an oscillator
Which component generate 50Hz frequency in this project
With my knowledge I think this is fake.
The glue holding all the mosfets is the first failure in this video.
All Of Them are failures, nothing on there except for the mosfets can withstand 2000W the transformer will die
@Robert Slackware true
@@McMasterProGenius Hello dude, i want to make a dual transformer inverter. Can i connect those transformer in parallel? E.g dual 500w to make 1000w inverter. All vid i've found just about rewinding those transformer.
@@maulidyen im not sure
This honestly completes my life. I'm making 80 of them :)
its work..?
I think there is a problem in keyboard of your computer specially in "0" key because it hits twice and sometimes three times!
😆😆😆😆😆😁😁😆😁😆😁😆😆😁😆😆😁😆
😆😆
Lol, 20 watt inverter, 2 watt inverter 😂😂😂
If that epoxy (or the tape) isn't a good enough heat conductor, then that entire heat sink is useless. Better would be drill and tap holes, then screw them down. Easy in Aluminum.
Do you even kapton?!? C'mon it's only 2kW and he is in pulsing the light bulb so the obviously that's what you should adhere to too two 2 /s
I am your fan
This is cool. One point to note is the durability of irf3205 mosfets on 12v source and inductive load is unreliable. Since there are neither any snubber protection nor schottkey diode in circuit, cant say how many of those mosfets survive.
IRF3205 mosfet 110A and 55V.
This mosfet is based on 110 amps. With 50% safety, it resists 50 Amps. 30 of them can give us 30 * 50 = 1500 Amps. For 12 Volts this means 12 * 1500 = 18000 watts. 4 mosfets are sufficient for 2000 watts.
Transformer link: 80W AC 220V To 24V Single Low Frequency E Type Isolation Small Power Transformer
This circuit does not work. Trasformator is powerless and wrong
Maybe the mosfets are so bad, he has to use so much of them... But this remembers me of an inverter to glow up a fluorescent tube up to 60W from 12V with one mosfet without any heatsink needed for small tubes and a mini ferrite transformator. So the biggest question is the waste of electronics for this. Think of the planet, please!
Small, simple and powerful..... 🔥🔥🔥
It's not powerful sir the mosfet very hot and not 2000w,the enamels cable use 1.5mm Not 2000watt only 500w and this inverter using zvs system not efficient. :(
@@electroniccreative7683
Yes, efficiency is not 2000w but simple and easy to build.
Why every you tuber show 500,1000,... ETC watt inverter and always glow 100 watt or led bulb 😑😑
ruclips.net/video/qj7Rfr9mkSw/видео.html
How does the circuit work, without an oscillator?
The ferrite transformer is very small and is intended for high frequencies and does not operate at 50/60 Hz
Genius guy genius thinking 👍💯
Watching from philippines
Fell background sound . Background sound is awesome 👌👍
Chal chutie
Весь этот канал похож на какой то троллинг
Really this is hundred percent successful I can believe
This is 100% stupid waste of resources... you can believe.
It would better if you showed or gave circuit diagrams of projects so that it is easier to follow.
If I may ask why were 30 MOSFETs necessary?
Didnt you notice the wire gauge connecting batter to 30 mosfets also?
That wire gauge was definitely not thick enough to utilize all those mosfets
Please say me where is the switching part of the mosfet.
Yeah I think this is fake
Nice god❤❤❤❤👍👍👍👍👍👌👌
Bro you are genius love
you have the construction diagram and the voltage 50 or 60Hz, and amperage specifications? The transformer that you indicate is 24V input and you are feeding it with 12V
Good name ,... American tech ! fits !
Really???
I never imagine glue transistors. Specially like this.
Dumb RUclipsr am i right?
@@McMasterProGenius Certainly
I think he make fool
Excellent project
The transzformer don't survive somani power 💥🔥⚡
ruclips.net/video/qj7Rfr9mkSw/видео.html
*I used those same Mosfets to repair a failed controller for my electric scooter. It blew up as soon as I hit the power. It was a combination of a bad board design and my laziness to add better insulation. I used 15 IRF 3205s. Pay no mind to the comments. This is interesting for me as I'm disabled and just holding a soldering iron is damned hard. Cheers.*
J
Hello! Mosfet IRF3205 can be replaced by infineon 65F6048A Mosfet?
En realidad pudieras usar casi cualquier Mosfet. Pero los recomendados para inversores de 12 VDC son los que tienen VGS de 10 voltios ya que el transistor entrega toda su potencia a ese valor. Si Ids es pequeña unes muchos Mosfet en paralelo para aumentar la corriente, pero lo recomendable es usar Mosfet con valores altos de Ids para no usar tantos componentes
Amazing sir you are 2 good supper
Simplest and easy to follow installation
Thank you for demonstration
That’s why my local electronic store ran out of mosfets >:P
😂😂😂😂
WTF? 30 fet for to turn on a bulb lamp under 100W? Jesus!!!
Insane!!!
ruclips.net/video/qj7Rfr9mkSw/видео.html
@@renatosaraivalima ikr🤣🥴
watch the video 2X speed ( Recommended )
I request RUclips to give 4X speed in new update to watch his videos...
😅
thats a good idea
nice КПД awesome ТЕПЛОВЫДЕЛЕНИЕ
MOSFETs thinking in this video:
Hey folks - he wants us to be an 2k Inverter. Let's generate a sine wave on our own and ignore that we're all wired parallel.
Common it's for RUclips - forget the physics for the next 12 minutes.
this video screams wrong in so many ways
i agree!!!
Sir the videos you made is very good. I need a exact inverter diagrem 10kw. Thanks for making the videos.
the yellow paste is used as heat paste or as glue
Lo siento mucho amigo ese disipador no es para esa potencia y se utiliza pasta termica no epoxico...... Espero me entiendas lo que quiero aclarar. Saludos
Very good Thank you
This simple and creative
youre gonna fry the mosfet and the transformer
squarewave AC can break some electronics
Mantap Bosku,👍👍👍
Hi brother plz tell this MOSFETs transistors touch with heat sink ?
Футурама какая-то 😁
Awesome👊
As a professional SMPS designer i have to ask you , DO YOU REALLY DESPERATELY NEED SUBSCRIBERS AND VIEWS ? First thing first , Ohm's law - let's assume that this , i must confess , visualy interesting design CAN deliver 2KW (in dreams maybe) , how much current will it draw from battery ? Almost 170 Amps from 12V , IF it's efficiency is 100% (impossible). Calculate wire gauge for that current.
Second, at high currents it is critical to distribute it across MOSFETS with proper wiring! Even 1cm of wire becomes small inductor and big problem.
Third , output voltage regulation and frequency. This is a blocking oscillator that oscilates at free running frequency that depends upon load, battery voltage etc.Output voltage is also very unstable.
Then there is cooling that is ridiculous ...
I really apreciate any kind of work and it's OK to be creative so thank you for this video. People should be inspired with science BUT please stop making toys and claim that they work as a serious device. This thing can deliver from few , to few tens of Watts at best.
Put your effort in real science and wanted success will surely come, including views and income ;)
Best luck.
Sweetheart and very nice video
Looks cool as hell though
The lamp is 2000W load? The battery can supply 2000W power?
Does a power supply adapter work?
How is the qualify of AC waveform?
it cant deliver 2k watts
, хороша сказочка.............
Woukd you pleaae let me know if 5kw or 10 kw.how much ampere trnansformerless needed and how many transistor or ic must be added?trims
It says 2000W invertor and you are showing a 20W bulb.
It's very grate
Hola, el disipador no sirve para eso, cada uno tiene una potencia de 200W según su datasheet, como hiciste para que no se te quemaran?
Los Mosfet están en paralelo y eso hace que la carga sea compartida.
I am skeptical on the 2000W rating. Unless the frequency is extremely high, that transformer is way too small
Very nice bro
Where is the oscillator???? You can not just feed DC into a transformer.... This is TOTAL B.S on so many levels. And gluing output devices to a heatsink would give very poor heat tranfer.
Try powering a microwave. If work your inverter is the best 😊
good luck with the video
los mosfets no calientan demasiado?
Saludos amigo...tienes muy buenas ideas... Pero es mejor ser más técnico y mostrar planos del proyecto y además las mediciones con instrumentos....He visto que colocas potencias y no son reales a simple vista.........Espero te guste esta crítica constructiva.......Saludos desde Colombia Medellín. Exitos
Fraude... No puede sacar 2kw con ese pequeño transformador de ferrita... Pero bueno...
Si ese transformador es de apenas 500w
what kind of transformer did you used for this.
Curious... how is this an inverter when your useing a DC power supply?
ruclips.net/video/qj7Rfr9mkSw/видео.html
quais transistores servem para fazer esse inversor ?
qual a resposta ?
Is this the wavy current you have done, the square flow. that is, it is a full sine inverter
12v × 8.2A = 98.4w diferente a 2kw
De donde sale la energia restante?
20000-98.4 = 1901,6w
1901,6? De donde salen?
If the circuit configuration in the video is practically providing 2000W In real time from a (12V, 8.2Ah battery), (MATHEMATICALLY) it has to be like this:⬇️
2000W= 12V × XA
XA= 2000W/12V
X= 166.7A
2000W= 12V × 166.7A
−−−−−−−−−−−
In this case, we need to extract 166.7A from a (8.2Ah battery)
So:
8.2A × 1h= ...... [h=hour]
[166.7≈ 8.2 × 20.3]
=(8.2 × 20.3)A × (1/20.3)h
[(1/20.3)hour= (60min/20.3)= 2.95minute]
−−−−−−−−−−−
So:
If the circuit configuration in the video is really providing 2000W In real time, the battery will last for 2.95 minutes only:
2000W= 12V × 166.7A
(for 2.95 minutes only)
Pls American tech except from the small transformer I wonder why a pulse width modulator is not used pls do reply
excuseme how many transformer amperes requiered this project for correct funcionally
O....... Thank bro😍😱😱😱😱😱😱😱
O
Top 👍😊
Will computer or refrigerator or something work with this inverter
Again only mosfets in parallel to support more current. You may use it to drive one of your diy high amp one phase bldc motors but not an ac motor. It s a square wave
Mosfets are used to produce Frequency. 4 Mosfets or 6 Mosfets are enough to produce sine wave
Mantap...rapi
Shall I connect 5amp trans former with this circuit
Neat. But I would test with a load that actually require a sinwave input.
Would be a square wave I'd imagine.
@@exogator Yes to do these claims he should test it with 2kW of power. But with that transformer I doubt it...
Amazing man
This circuit is free willing no frequency control no need huge quantity install mossfet can be experiment 4 or 6 mossfet
What happens when the glue melts.
Kaboom....
Kaboom....
can i use 12-0-12 10amp 10000mah 220volt ac step down vertical mount transformer instead of small transformer and can i run refrigirator500w tv 150w and vaccum cleaner1000w at a time
Nice video bro👌👌👌👌
Does this circuit work for long hour?
Try with drill,powerfull inverter need big battery and big transform..
Посмотрел некоторые видео с вашего канала,мне понравилось.подписался.
You should Try to use 4047 ıc and bigger than this trasformator.Thank you for video.
the drain of the MOSFETs connected each to other in heatsink. drain must be short.
Heat sink looks inadequate for 30 transistors ?
すげえ量の部品だなぁ！
ruclips.net/video/qj7Rfr9mkSw/видео.html
What's the point of the heat sink if you epoxy your mosfet on epoxy isn't what we would call thermally conductive
2000 watts for mosfet bank circuit, 75 watts for that small step-up transformer.
What type of Transformer?
How many amps would that sad and lonely battery need to supply at 12V in order to produce those 2000W ?
yep, quality content my ass
Powerful MOSFETs are pretty poor in this design (a multivibrator). If you look at the current generated with an oscilloscope you'll have a heart attack. Oscillations must be made with low power transistors (or MOSFETs) and the powerful ones are used only for switching. As it is 150 Watt is an absolute maximum of what this thing can deliver, especially continuously.
فديو رائع.خمس نجوم.
اذا كانت المحولة بخطين وليس ثلاثة كيف يكون الربط.؟؟
Well. That will only produce something like a square wave. You might use it to light up a bulb but not to run an ac motor efficiently. Moreover, the output frequency is very high.
2000 Watt Inverter can drive the 60 Watt light bulbs !
Ok.
LOL.
More watt ?
Testing the 2 KW heater !
Hahaha...
Please how much is all the transistor mosfet
Na realidade a Potência maxima real é 1320wats.(se a frequência é alta em relação aos 60hz normal, a potência se compara a 2000 Wats certamente. Isso se...Se tiver corrente suficinte na bateria! 😉😄
Mas se ele usar uns capacitores de alta frequência na entrada 15v em mega farad e uns na saída 400v. Acho que dar uma potência a mais ripow
Always his video is oddly satisfied..
Nice.👍