I’m here because I found the video of joe using the 9 volt battery’s I would love to do a project on this. I’m very inspired good video. No relation to Joe 😀
If you shorted out the cap FIRST to prove there was no energy, then connected it and then finally disconnected the batteries and it still ran (with no hidden forced airstream, like all the other scammers), then you will have something, but currently you have exactly a newman motor (aka not perpetual). Its fun to experiment, keep it up.
I noticed when Joseph demonstrated his motor, the meter would show negative voltage on front end while running. Have yet to see duplicated, but nice job.
To anyone that leaves a comment, I remember watching a video where Joseph Newman said the cells on the right side in the back of big Eureka were capacitors, but I've searched for about 15 minutes and I cannot find the video where he tells you what those two objects are, I'm remembering a capacitor, but if you run into the video can you please tell me the name of the video thank you God bless
i have no electrical back ground but have been watching a lot of video's about free energy and magnets and all that but i think he gets the torque by the transformer boosting up the volts from what ever volts he is putting in. just my thought go back and check out some of his video's where he is in the garage. i saw one of his old video's once where he really showed the whole thing and explained it to
Hello Ed Cupp: I love your expertise in replicating some of the stuffs, for some time I have not seen any new videos of yours more over the Microwave oven coil Newman motor, can you let me know if you have made any schematic diagram and show all individual assembly parts for the newman machine at this time, or let me know if you can fully assemble one for me at a cost> Thanks Waiting for your reply asap. Joe
Nomans engine put out more voltage then it used this is a great idea and I would like to see these in cars boats tractor's putting out more power then they use this could the world every one could afford to get power GOD showed noman all good things come from GOD and this is good......GOD is good yes he is....
I did some experimenting with smaller wire versus bigger wire both of the coils came out of a microwave the big wire took a lot less energy to pulse the magnet then the little wire and I got a lot more back EMF off of the big wire the weight of the wire was probably heavier on the thicker wire but I really didn't weigh it so I'm not sure but it sounds like a good experiment I have to try thanks for your comment
This particular motor only fires twice every Revolution so to add more magnets I would have to put them in the same place I can build another motor and spread the magnets farther apart which would give me more leverage 4 power, which may be what Joseph Newman did? Thank you for your comment God bless
As proof of Concepts why didn't you short out capacitor forehand? All that looks like you did was connect to supercab to a motor. Ergo the motor runs off of the super cap
I've received a few requests so I think I will make it tutorial video, the motor is made from microwave parts but it may take me a while to find the right microwave God bless and thanks for your comment
@@fpveddie I just sent you another request because I had already went through a couple other request from people wanting an instructional video from you about the construction of this type of motor especially with the parts being recycled from the microwave and any other parts from a recycled source if possible.
bro solar cell was less than 130 miliamps''' 3 lil garden cells in parallel gave me 3.2 volts and bout 130 mili amps'' dont need and cicuitry at all or cap'' if u put bridge rectifier across coils' u can charge over 450 dc cap like i did in seconds'''''''''its not the cap that was running it' it was purely the cell'')::) then add cap and u see what i mean__"" it was freaking awesome in my opinion"_'-
I don't understand what the deal with the capacitor is, its just a battery that will charge and discharge faster than a battery, so connecting the cap is just like connecting another battery,
@@vicmartinez3711 if you can build a small prototype then you can upscale it to do whatever you want, this has already been proven, Joseph Newman gave up most of his life to try to prove to people it was real, for me I'm not willing to do that, until people become more open-minded they won't see it anyway
If I gave you a million dollars, could you make a Newman motor capable of running an air conditioner? How much electricity would this "perpetual motion machine" actually use to run an AC?
Hello Ed Cupp. I appreciate what you did. It's great work. You made a 2/3 of Newman motor. I assume you are older than 50, so teaching you will be probably a little harder. Most of men (99%) were never grown into men because there were no man in their lives who could told them a wisdom. Therefore they stay a boys. That mean that their consciousness never transfer from second chakra to six chakra. Practically that mean that those boys in man body react wrong upon teaching especially in older ages. Instead embrace the teaching, they swing to himself thinking "oh I am doing such a great matter to help humanity and they animadvert me" and they close up in frustration. That is what I am trying to avoid here. First you have to understand what you did is just a simple DC motor. Second you have no idea what back EMF is. And at least Newman motor is only a simple DC motor with back EMF. That back EMF is charging batteries back. Because in your circuit is no back EMF batteries will run out. Back EMF is captured with diode. Best are powerful shotkey diodes (30A and above). Efficiency of back EMF grows with voltage. Therefore Newman used a biiiig coils. Biggest is coil greater is induction, consequence is greater back EMF. If you test machine enough time you will discover that you have to go over 300V for achieve some results. It's mean 300V on batteries. Back EMF goes over 3KV or 5KV if it is open. Usually that mean you need two pack of batteries. First one fire a motor, second one is collecting a back EMF. And in second half rules are reversed. But, yes there is always but, when we talking about back EMF things goes complicate. We have to figure out about which back EMF we are talking about. There is a lot of it. There is a pore basic explanation of Back EMF in motor, and that IS NOT THE Back EMF we are talking about -> ruclips.net/video/5mf4NmmLWnE/видео.html Back EMF we are talking about is like on this video -> ruclips.net/video/0BPphesBGg0/видео.html There a guy trying to capture Back EMF with a capacitor. It will never work because voltage in cap increase and therefore charge current decrease. Therefore is no OU. It need to be batteries. If cap is added is even better, but only cap no way. With BATTERIES THERE IS OU. Because of nature of Back EMF and the batteries it has been proved that those type of motor runs best on high voltage and minimum current. That way batteries even increases on voltage during operation. But you can not mislead yourself that this is the same power that it is in regular charged batteries. There is voltage but a very little juice. If we put a light bulb on that battery it will be drained out very fast. But in a motor circuit it will never discharge. There on collector must be a several contact not just one, so it can be a several cycles of charging / discarging of coil.
Please explain to me how the capacitor speeds up the motor when the batteries are almost dead, especially when they stopped running the motor themselves? As far as the chakras oh, I'm sure all my chakras are in line, just like most people, but if you can explain how the motor runs with the capacitor but not without, would be appreciated, love to hear your thoughts
XTENTA no the fish only lasted about 45 minutes total but that fish help to give me the motivation to start posting videos on the truth thanks for your question God bless
@@fpveddie is it possible you could do an instructional video using the microwave coils with any and all possible scrap parts or list parts that are obtainable thru recycling? It would be highly appreciated by many others than just myself from what I've read in the comments section of this video, your narrations are superb and what is needed in an instructional video about this style of motor and with the fact that we can no longer get it directly from either of the horses mouths (RIP JOE & JOHN), you are in my opinion the next best person for the job, what do you say ay?
@@slayerdpimp9690 thank you for the kind words, I know I can't come close to feeling any of their shoes, but I can share a little bit I think I understand
i have watched a bunch of different videos and he newman had transformers on his system, go back and watch on the right side of the trailer big sits on and u will see the small transformers on the trailer. the transformers have two horn like things sticking out of the top of the box that they are apart of.
I'm not sure if Transformers work like capacitors or not but I'm pretty sure they were AC Transformers, I was calling them capacitors I'm really not sure the difference if there is one?
Think of capacitors like a bucket to hold charge. Transformers change amperage and voltage. As the voltage increases the amperage decreases and vice versa. So the energy in is about the same as the energy out but transformed hence the name.
I left some details of everything I think I understand in Tim Allen's comment above please check it out if you have anymore questions I will try to answer them, and I'm going to make a tutorial video on how to make a microwave motor which is what this one is thanks for your comment God bless
Your right, as little a current flow as possible,, Joe ran his 7500 pound motor on 750 volts at 1/4 amp.. sadly, Joe passed away in 2015.. He was a cool guy.
That's true, the batteries are pretty dead they only have voltage but the voltage is translated into instantaneous current with the capacitor, because no matter what you need some form of current to pause a magnet, but you are right it runs on voltage because the batteries are dead
hey bro this might interest u also guy has site on youtube here call ray0energy has a vid named sparky newman motor u got to see it):):);0 another one of interest is... Newman motor generator 20v in over 200v out! By El lotto king he shows how to use small wire around the initial coil as gen lighting over 200 leds is a must watch in my opinion i hope u see the vids man and enjoy:)0; keep up the good work:):)
I just went through a lengthy explanation what I think I understand on Tim Allen's comment above please check it out if you have anymore questions I will try to answer them God bless
did you try with more volts like 1000 and more to create strong magnetic field to turn on some big shaft?I have some experiments I did and u can see some ideas about strong magnetic field hope you will try to make 1 big...regards.
That's something that I know won't work, because a capacitor and the battery are two different things the only similarity is that you need to charge them, if I start with a dead capacitor as soon as the motor shorts the capacitor out the voltage will be gone, and I already know that I need between 200 and 400 lb of wire to gain enough back EMF to exceed the input power, but no matter what we will always need some voltage to trigger the coil the capacitor merely turns it into instantaneous current, which is all that is needed to run a motor, but thank you for your comment, and please try to remain open-minded because it's the only way to keep that door of possibility open, God bless
I've got the Wonder though.. who is in possession of big Eureka.. I'm curious to know this and all of his works and papers..???...probably confiscated just like they done Tesla ....government is nothing but terrorists and should be thoroughly dealt with by freedom-loving human beings.... I'm going to build one of these motors I will start out with a small unit like yours probably the same way because that was the idea I had then ran across your video using microwave Transformer.. so that's what I'll use but I'm going to use the secondary windings as they're about two to three thousand turns in that coil, more turns the better apparently.... once I get the system down pat... I will be building a bigger one.. a three or four hundred pound version... I have tons of smaller capacitors and some 4- 5000 volt DC capacitors out of several defibrillators I picked up at a recycling yard... I should already have enough stuff to build the bigger unit except for bigger magnets that's the only thing I will need
Someone has already asked , I'm gonna ask again! Has anyone put a load on it to see how much drag it can handle? I can see that it is producing extra electric! But anyone that knows capacitors... they have an extra charge in them already! So if that cap already has a charge it will produce the extra kick! If the machine is producing volts to the capacitor yes there is extra electric going into the capacitor for the extra power, but if there is drag on the machine will it produce volts! And using it (the machine) can also do work, 'then' and produce electric, then this is a Viable source of both Workable power and electric! Big bertha was a pump and did produce work and extra electric! Sorry! I'm not into religion and dont believe ! This is science thats all! I hate government! If this truly works I dont understand why the patent office would not give him his patent! The only thing that I can figure is, what i'v said for years that the government is total controlling every aspect of our life ! And because in the science community it would mess up every known thing they have worked on!
It has a little bit of torque but not much I don't have near enough wire to produce the required back EMF, my experiments showed me that the more wire you use the more back EMF you get to translate into instantaneous current with a capacitor thanks for your comment
I think the reason Newman couldn't get a patent it's because his motor would undermine the monetary system, I'm still trying to figure out why we need the system at all?
From my experiments I'm some DVDs I have of John bedini I've learned that the more wire you add the more output you get while using the same or less input, I know that when the batteries are two dead to run the motor that's in the video all I have to do is hook up the capacitor and it will start running, and it's true that when the capacitor sets it will slowly gain a little bit of voltage but as soon as it is shorted out that voltage is gone, I know there is a lot of back EMF that came off of a larger motor that I put together using a coil that way about 60 lb, because when a friend and I powered it up and it was in a building that had a security system they ran on 2.4 gig it didn't take too long and he got a phone call from the security company so we had to shut the motor down LOL plus when the motor is running the meters that are around it go crazy you don't have to even connect to anything, I like skepticism, in some ways it's the only thing it helps protect some of these awesome inventors, but on the flip side of the same coin, it also makes it easy for the people in power to keep this technology suppress, so thank you for your comment and try to be open minded because it's the only way to keep the door of possibility open, thanks for your comment God bless
Ed Cupp if I was Newman and found my efforts to do things legitimately roadblocked by government and industrial agencies, I would have drawn schematics and instructions and just scattered them across the country. The potential for open sourcing would undermine the attempts to discredit and stymie this kind of project. Put it out there, and let anyone who understands the process (I do not, unfortunately) improve on it. If he had done that instead of holding out for his own development things could be way different today.
Ofcourse it keeps on running. The Capacitor has all the power to make the engine run. Likely it will add some juice to the batteries too. Not sure what these Newmanians are trying to prove to show that Engines are running on Voltage - not on Current - nonsense. Playing with engines is fun. Big Eureka is big Bull. So is this video by the way. There is no "serious" tech measuring involved and no timely registration of either Volts or Amps; just momentary glympses. No "undressing" what device is used actually (type of engine, windings etc.) I haven't seen a single scientist knowing electronics in any of the videos. Most of them are asking questions that don't even question this very questionnable "tech". Just very sad to see this being brought to people and continuing to focus on Amperage and Voltage while both capacitors and coils are in there. You won't prove anything unless you have a full timely trend or a schematic and show people where these schematics don't add up. Until that moment, you are not proving anything and you are convincing complete idiots not knowing what they are looking at and not knowing how electricity works. It's pretty easy to fool a fool; it's way more difficult to fool an -actual- scientist (yet not impossible). I.e. by putting batteries in large chunks of a large machine or by putting them in something what seems to be a capacitor. This shouldn't be under Science & Tech but under "Magic tricks".
The Newman Motor runs on fairy dust and wishful thinking. It's a big fail because Newman had no clue what he measured and made unproven claims. Just a simple children's motor. Nice build though. It is under unity.
Thanks mr Cupp. It's 6 years on since you made this video, it's kind of you to pass on your knowledge. God bless.
I’m here because I found the video of joe using the 9 volt battery’s I would love to do a project on this. I’m very inspired good video. No relation to Joe 😀
I would loved to have a motor like that in my boat thanks for the video.
Pulse a coil in solid state at 0 AMP, charging capacitor with the pulse, discharge capacitor on the motor coil.
If you shorted out the cap FIRST to prove there was no energy, then connected it and then finally disconnected the batteries and it still ran (with no hidden forced airstream, like all the other scammers), then you will have something, but currently you have exactly a newman motor (aka not perpetual). Its fun to experiment, keep it up.
I noticed when Joseph demonstrated his motor, the meter would show negative voltage on front end while running. Have yet to see duplicated, but nice job.
To anyone that leaves a comment, I remember watching a video where Joseph Newman said the cells on the right side in the back of big Eureka were capacitors, but I've searched for about 15 minutes and I cannot find the video where he tells you what those two objects are, I'm remembering a capacitor, but if you run into the video can you please tell me the name of the video thank you God bless
i have no electrical back ground but have been watching a lot of video's about free energy and magnets and all that but i think he gets the torque by the transformer boosting up the volts from what ever volts he is putting in. just my thought go back and check out some of his video's where he is in the garage. i saw one of his old video's once where he really showed the whole thing and explained it to
In my mind I remember can you call him it a capacitor, but I will check out the video again to make sure thanks for your comment God bless
Good work thumb 👍
Hello
Ed Cupp:
I love your expertise in replicating some of the stuffs, for some time I have not seen any new videos of yours more over the Microwave oven coil Newman motor, can you let me know if you have made any schematic diagram and show all individual assembly parts for the newman machine at this time, or let me know if you can fully assemble one for me at a cost>
Thanks
Waiting for your reply asap.
Joe
@Ed Cupp schematics would be awesome please and thank you
Nomans engine put out more voltage then it used this is a great idea and I would like to see these in cars boats tractor's putting out more power then they use this could the world every one could afford to get power GOD showed noman all good things come from GOD and this is good......GOD is good yes he is....
From what I understand it takes between 4 to 600 pounds a wire to generate more radiant energy then the input power
Ed Cupp according to the review work of roger Hastings, the small unit he tested had 145 lb mass of copper and about a 17 lb rotor.
add some magnets around your motor it will increse the effiency and speed with the micro coils
I did some experimenting with smaller wire versus bigger wire both of the coils came out of a microwave the big wire took a lot less energy to pulse the magnet then the little wire and I got a lot more back EMF off of the big wire the weight of the wire was probably heavier on the thicker wire but I really didn't weigh it so I'm not sure but it sounds like a good experiment I have to try thanks for your comment
This particular motor only fires twice every Revolution so to add more magnets I would have to put them in the same place I can build another motor and spread the magnets farther apart which would give me more leverage 4 power, which may be what Joseph Newman did? Thank you for your comment God bless
Does it produce more than it takes in???
You know you can use the back spike or back emf as power to charge the batteries or even run light and motors
Plug it into a phone line theres 50VDC in there but almost no current
As proof of Concepts why didn't you short out capacitor forehand? All that looks like you did was connect to supercab to a motor. Ergo the motor runs off of the super cap
Hi Ed, and thanks for the video! Can you provide a schematic of the circuit? Thanks.
Very, cool. Could you show how you created that machine?
I've received a few requests so I think I will make it tutorial video, the motor is made from microwave parts but it may take me a while to find the right microwave God bless and thanks for your comment
@@fpveddie I just sent you another request because I had already went through a couple other request from people wanting an instructional video from you about the construction of this type of motor especially with the parts being recycled from the microwave and any other parts from a recycled source if possible.
bro solar cell was less than 130 miliamps''' 3 lil garden cells in parallel gave me 3.2 volts and bout 130 mili amps'' dont need and cicuitry at all or cap'' if u put bridge rectifier across coils' u can charge over 450 dc cap like i did in seconds'''''''''its not the cap that was running it' it was purely the cell'')::) then add cap and u see what i mean__"" it was freaking awesome in my opinion"_'-
Es ist nun wirklich kein Problem, aus 12 Volt 220 Volt zu machen... man nehme einen Trafo...
Interested in design schematics, plans.
The motor is made from a microwave, I'm searching for the right microwave so that I can make it tutorial video, thank you for your comment God bless
I don't understand what the deal with the capacitor is, its just a battery that will charge and discharge faster than a battery, so connecting the cap is just like connecting another battery,
Cool
What is the highest gpm pump your newman motor can drive?
Gpm?
@@fpveddiegallons per minute or liters per minute
@@vicmartinez3711 okay? There's no pump hooked to it, I think you're confusing my video with Joseph Newman's big Eureka LOL
Then beyond an intellectual curiosity, what is the value of your motor if it cannot drive a simple water pump?
@@vicmartinez3711 if you can build a small prototype then you can upscale it to do whatever you want, this has already been proven, Joseph Newman gave up most of his life to try to prove to people it was real, for me I'm not willing to do that, until people become more open-minded they won't see it anyway
If I gave you a million dollars, could you make a Newman motor capable of running an air conditioner? How much electricity would this "perpetual motion machine" actually use to run an AC?
and solar cells bro;;; without any solid state or capacitors''''
i have one running on 3 volts of solar cell
with nothing else'
I'm not a hundred percent sure but I think that you get some current either from solar panels or from the converter it may have capacitors in it?
Hello Ed Cupp. I appreciate what you did. It's great work. You made a 2/3 of Newman motor. I assume you are older than 50, so teaching you will be probably a little harder. Most of men (99%) were never grown into men because there were no man in their lives who could told them a wisdom. Therefore they stay a boys. That mean that their consciousness never transfer from second chakra to six chakra. Practically that mean that those boys in man body react wrong upon teaching especially in older ages. Instead embrace the teaching, they swing to himself thinking "oh I am doing such a great matter to help humanity and they animadvert me" and they close up in frustration. That is what I am trying to avoid here.
First you have to understand what you did is just a simple DC motor. Second you have no idea what back EMF is. And at least Newman motor is only a simple DC motor with back EMF. That back EMF is charging batteries back. Because in your circuit is no back EMF batteries will run out.
Back EMF is captured with diode. Best are powerful shotkey diodes (30A and above). Efficiency of back EMF grows with voltage. Therefore Newman used a biiiig coils. Biggest is coil greater is induction, consequence is greater back EMF. If you test machine enough time you will discover that you have to go over 300V for achieve some results. It's mean 300V on batteries. Back EMF goes over 3KV or 5KV if it is open. Usually that mean you need two pack of batteries. First one fire a motor, second one is collecting a back EMF. And in second half rules are reversed.
But, yes there is always but, when we talking about back EMF things goes complicate. We have to figure out about which back EMF we are talking about. There is a lot of it.
There is a pore basic explanation of Back EMF in motor, and that IS NOT THE Back EMF we are talking about -> ruclips.net/video/5mf4NmmLWnE/видео.html
Back EMF we are talking about is like on this video -> ruclips.net/video/0BPphesBGg0/видео.html There a guy trying to capture Back EMF with a capacitor. It will never work because voltage in cap increase and therefore charge current decrease. Therefore is no OU. It need to be batteries. If cap is added is even better, but only cap no way. With BATTERIES THERE IS OU.
Because of nature of Back EMF and the batteries it has been proved that those type of motor runs best on high voltage and minimum current. That way batteries even increases on voltage during operation. But you can not mislead yourself that this is the same power that it is in regular charged batteries. There is voltage but a very little juice. If we put a light bulb on that battery it will be drained out very fast. But in a motor circuit it will never discharge.
There on collector must be a several contact not just one, so it can be a several cycles of charging / discarging of coil.
Do tell
Please explain to me how the capacitor speeds up the motor when the batteries are almost dead, especially when they stopped running the motor themselves? As far as the chakras oh, I'm sure all my chakras are in line, just like most people, but if you can explain how the motor runs with the capacitor but not without, would be appreciated, love to hear your thoughts
Is the fish still alive?
XTENTA no the fish only lasted about 45 minutes total but that fish help to give me the motivation to start posting videos on the truth thanks for your question God bless
@@fpveddie is it possible you could do an instructional video using the microwave coils with any and all possible scrap parts or list parts that are obtainable thru recycling? It would be highly appreciated by many others than just myself from what I've read in the comments section of this video, your narrations are superb and what is needed in an instructional video about this style of motor and with the fact that we can no longer get it directly from either of the horses mouths (RIP JOE & JOHN), you are in my opinion the next best person for the job, what do you say ay?
@@slayerdpimp9690 it may take a little while but I will do my best
@@slayerdpimp9690 thank you for the kind words, I know I can't come close to feeling any of their shoes, but I can share a little bit I think I understand
@@fpveddie thank you for your fast response, no need to reply to the other request, thank you again,
God Bless you and all of your works
can you email me the diagram of this motor
i have watched a bunch of different videos and he newman had transformers on his system, go back and watch on the right side of the trailer big sits on and u will see the small transformers on the trailer. the transformers have two horn like things sticking out of the top of the box that they are apart of.
I'm not sure if Transformers work like capacitors or not but I'm pretty sure they were AC Transformers, I was calling them capacitors I'm really not sure the difference if there is one?
capacitors are like batteries and transformers boost your input to a really lot more
@@jjg2824 capacitors are like batteries in the respect that you have to charge them, that's where the similarity ends
Think of capacitors like a bucket to hold charge. Transformers change amperage and voltage. As the voltage increases the amperage decreases and vice versa. So the energy in is about the same as the energy out but transformed hence the name.
Details plan ?
I left some details of everything I think I understand in Tim Allen's comment above please check it out if you have anymore questions I will try to answer them, and I'm going to make a tutorial video on how to make a microwave motor which is what this one is thanks for your comment God bless
newmans motor doesnt run on current man;;;;;;;;;;;;;;;;;;;;;;;;;;;; it runs on voltage''''
Your right, as little a current flow as possible,, Joe ran his 7500 pound motor on 750 volts at 1/4 amp.. sadly, Joe passed away in 2015.. He was a cool guy.
I'm translating his commutator to solid-state switching. @@THOMASTHESAILOR
And yes, R.I.P. Joseph Newman.
That's true, the batteries are pretty dead they only have voltage but the voltage is translated into instantaneous current with the capacitor, because no matter what you need some form of current to pause a magnet, but you are right it runs on voltage because the batteries are dead
@@GaryMcKinnonUFO would love to see a video when it's complete :-)
hey bro this might interest u also guy has site on youtube here call ray0energy has a vid named sparky newman motor u got to see it):):);0 another one of interest is... Newman motor generator 20v in over 200v out! By El lotto king he shows how to use small wire around the initial coil as gen lighting over 200 leds is a must watch in my opinion i hope u see the vids man and enjoy:)0; keep up the good work:):)
Thank you I will check it out God bless
is working or???any1 tried to replicate pls answer who can thanks.
I just went through a lengthy explanation what I think I understand on Tim Allen's comment above please check it out if you have anymore questions I will try to answer them God bless
did you try with more volts like 1000 and more to create strong magnetic field to turn on some big shaft?I have some experiments I did and u can see some ideas about strong magnetic field hope you will try to make 1 big...regards.
Start with a completely discharged capacitor and don't connect the battery at all. Then see if it runs.
That's something that I know won't work, because a capacitor and the battery are two different things the only similarity is that you need to charge them, if I start with a dead capacitor as soon as the motor shorts the capacitor out the voltage will be gone, and I already know that I need between 200 and 400 lb of wire to gain enough back EMF to exceed the input power, but no matter what we will always need some voltage to trigger the coil the capacitor merely turns it into instantaneous current, which is all that is needed to run a motor, but thank you for your comment, and please try to remain open-minded because it's the only way to keep that door of possibility open, God bless
why video so close up,,so dark get some light...
I've got the Wonder though.. who is in possession of big Eureka.. I'm curious to know this and all of his works and papers..???...probably confiscated just like they done Tesla ....government is nothing but terrorists and should be thoroughly dealt with by freedom-loving human beings.... I'm going to build one of these motors I will start out with a small unit like yours probably the same way because that was the idea I had then ran across your video using microwave Transformer.. so that's what I'll use but I'm going to use the secondary windings as they're about two to three thousand turns in that coil, more turns the better apparently.... once I get the system down pat... I will be building a bigger one.. a three or four hundred pound version... I have tons of smaller capacitors and some 4- 5000 volt DC capacitors out of several defibrillators I picked up at a recycling yard... I should already have enough stuff to build the bigger unit except for bigger magnets that's the only thing I will need
We need the circuit diagram
Absolute ignorance
Someone has already asked , I'm gonna ask again! Has anyone put a load on it to see how much drag it can handle? I can see that it is producing extra electric! But anyone that knows capacitors... they have an extra charge in them already! So if that cap already has a charge it will produce the extra kick! If the machine is producing volts to the capacitor yes there is extra electric going into the capacitor for the extra power, but if there is drag on the machine will it produce volts! And using it (the machine) can also do work, 'then' and produce electric, then this is a Viable source of both Workable power and electric! Big bertha was a pump and did produce work and extra electric! Sorry! I'm not into religion and dont believe ! This is science thats all! I hate government! If this truly works I dont understand why the patent office would not give him his patent! The only thing that I can figure is, what i'v said for years that the government is total controlling every aspect of our life ! And because in the science community it would mess up every known thing they have worked on!
It has a little bit of torque but not much I don't have near enough wire to produce the required back EMF, my experiments showed me that the more wire you use the more back EMF you get to translate into instantaneous current with a capacitor thanks for your comment
I think the reason Newman couldn't get a patent it's because his motor would undermine the monetary system, I'm still trying to figure out why we need the system at all?
From my experiments I'm some DVDs I have of John bedini I've learned that the more wire you add the more output you get while using the same or less input, I know that when the batteries are two dead to run the motor that's in the video all I have to do is hook up the capacitor and it will start running, and it's true that when the capacitor sets it will slowly gain a little bit of voltage but as soon as it is shorted out that voltage is gone, I know there is a lot of back EMF that came off of a larger motor that I put together using a coil that way about 60 lb, because when a friend and I powered it up and it was in a building that had a security system they ran on 2.4 gig it didn't take too long and he got a phone call from the security company so we had to shut the motor down LOL plus when the motor is running the meters that are around it go crazy you don't have to even connect to anything, I like skepticism, in some ways it's the only thing it helps protect some of these awesome inventors, but on the flip side of the same coin, it also makes it easy for the people in power to keep this technology suppress, so thank you for your comment and try to be open minded because it's the only way to keep the door of possibility open, thanks for your comment God bless
@Bill Miles I think Joseph Newman is more powerful now, with a lot of help
Ed Cupp if I was Newman and found my efforts to do things legitimately roadblocked by government and industrial agencies, I would have drawn schematics and instructions and just scattered them across the country. The potential for open sourcing would undermine the attempts to discredit and stymie this kind of project.
Put it out there, and let anyone who understands the process (I do not, unfortunately) improve on it.
If he had done that instead of holding out for his own development things could be way different today.
Ofcourse it keeps on running.
The Capacitor has all the power to make the engine run.
Likely it will add some juice to the batteries too.
Not sure what these Newmanians are trying to prove to show that Engines are running on Voltage - not on Current - nonsense.
Playing with engines is fun.
Big Eureka is big Bull.
So is this video by the way.
There is no "serious" tech measuring involved and no timely registration of either Volts or Amps; just momentary glympses.
No "undressing" what device is used actually (type of engine, windings etc.)
I haven't seen a single scientist knowing electronics in any of the videos.
Most of them are asking questions that don't even question this very questionnable "tech".
Just very sad to see this being brought to people and continuing to focus on Amperage and Voltage while both capacitors and coils are in there. You won't prove anything unless you have a full timely trend or a schematic and show people where these schematics don't add up.
Until that moment, you are not proving anything and you are convincing complete idiots not knowing what they are looking at and not knowing how electricity works.
It's pretty easy to fool a fool; it's way more difficult to fool an -actual- scientist (yet not impossible).
I.e. by putting batteries in large chunks of a large machine or by putting them in something what seems to be a capacitor.
This shouldn't be under Science & Tech but under "Magic tricks".
The Newman Motor runs on fairy dust and wishful thinking. It's a big fail because Newman had no clue what he measured and made unproven claims. Just a simple children's motor. Nice build though. It is under unity.