Very good video. Thank you. Detailed explanation. Give us a bit of theory on choosing capacitors and resistors since I am an Aero engineer. It helps people like me to get deep into electronics.
Bahut accha video hai Dost, Great information for diy users, Very neatly explained in details. Plz tell value of Mov . Just tell me if same can be used on Dob also. Baki sab 1st Class hai.Thanks you
sir aapne mov ko rectifier ke baad lagaya hai.kya transformer wale power suply main bi mov ko rectfier ke baad main laga sakte hai.maine 6 volt 0.5 amp ka power suply banaya hai.mere pass 7d 471 no.ka mov hai.plese reply.
Very Well explained but one quarry left regarding after glow problem. Please let me know the value of resistance and mounting position . One more question regarding mounting of mov whether it is better used in ac section or in dc section. Should I use any pf like 474 j 450 volt in ac section for better protection after mov . Your suitable reply will be highly appreciative.
Ramesh ji thanks for your valuable comment Use mov in ac section, fusible resistance 100ohm to 47ohm .05 watt Low glow led this is for 100ma led mcpcb ,if your led need more current use high value pf
@@A2Aelectronic lot of thanks for your prompt reply. Sir my question for after glow not for low glow. Please suggest the value of resistance which should be connected with output capacitor to prevent after glow problem.
@@A2Aelectronic Thanks for the practical circuit diagram. MOV shown after DC. Please explain the detailed calculation about choosing capacitor. The whole circuit works on the principles of capacitive Reactance formula. You used 155j 400v. Why not 105j, 225j, 335j? Yes, Please inform the output Voltage DC and it's Current capacity. Awaiting your reply. 👍
3watt ke lie jo 22ohm ki resistance he uski value 47ohm to 100ohm Kar sakte ye led ki current pe depend karta he ye circuit 100mA ke lie he agar 3watt bulb me 100mA ki led use ki gai he to 22ohm ki resistance hi kaam karegi
MOV ka value Dena chahiye thaa.(07D511K) MOV DC side me lagaya, but similar MOV AC side me bhi lagana chahiye thaa. Because it's most important. and Filter capacitor velue is questionable.
After bridge rectify voltage would be increased by 1.4 so usually voltage would be around 310 volt ...and use of electrolytic caps below voltage seems questionable ....does MOV adjust the volt there ???
MOV is only protection for spike ⚡ peak value is taken accordingly, which is 230x1.44. So capacitor value rating is 450v or 400v. Mov is used for protection against high voltage which becomes short circuit or burst and voltage cannot pass through further. Search for Capacitive Reactance formula in RUclips you will find details about the same. 👍
In diagram you showing mov is connect with DC current it is right or wrong? pls reply me? second think you not show how many ohms discharge capacitor ? pls reply
Can I use pf 125j 400 volt with 100uf 100 volt capacitor but when I Seen dc voltage in multimeter it show only 59volt without 9watt led what reason voltage is showing very low?
Thanks sir mere pass ek 7 led wala circuit h jisme afp224 0.22 micro farade ka capastor laga h jisme led glow nahi ho rahi h brize diode sahi kya problem ho sakti h
me apka video dekhkar same 2 same banaya tha mgr mera output ka 22ohm ka resistance kuch second me fuk ja rha hai , mene 1 watt ka v lagaya wi thode der bad fuk ja rha h . aisa q plz reply
Bridge Rectifier main out put mai to 220 volt dc aayega to vaha Filter Capacitor 100 volt ka kaise lage ga? Vaha 400 ya 450 volt ka capacitor laga na pde ga na???
Sare circuit diagram se hi bante he naki practical , practical se keval simple circuit samjh me aa sakta he lekin jab circuit complicated hota he to aap vina diagram ke nahi bana sakte इसीलिए circuit diagram ko samjhna sikhie tabhi electonics me success honge aap video dekhne ke lie Thanks
Rasistance 22ohm, use 10 ohm brightness bad jaegi mujhe lagta he aap jo led use kar rahe he high current MCPCB he , ye circuit 100ma MCPCB ke lie he Rasistance value kam karne se brightness bad jaegi
Nice LED circuit.
❤️
Sir aap ne achhi information dia thanks
❤️
Aise banane se roshani kam hota hai
good teacher sir
Very good
Very very good presentation good explain thanks
Thanks
Very good video. Thank you. Detailed explanation. Give us a bit of theory on choosing capacitors and resistors since I am an Aero engineer. It helps people like me to get deep into electronics.
Thanks for watching my vedio
Hello derakanath ji Please wisit my website www.a2acircuits.com detailed article on capaciter Please visit
Very good video for my knowledge. For Rural Area Driver circuit diagram
Very good explanation
Super guidelines Sir..
Thanks
Very nice
❤❤🙏🙏
Informative video sir impedencc formula b bta datay TU good hota
Ok
Thanks for your nice video god bless you🙏🙏🙏
Thanks
Thanks
❤your vdo
Jai hind sir simpl but very good knowledge sir
Thanks
very good video thanks
Good 👍
❤❤
بہت خوب میں نے بہت وڈیوز دیکھی ھیے پر آپ جیسا استاد نھیں دیکھا بہتر کام
Excellent explanation Thank you
Thanks
Thanks
👌👌👌 many many thanks sir 🙏🙏🙏.
Thanks
Very nicely explained sir. Thank you very much. Pls muze 3watt led ko chalane ke liye is circuit me kya change karna padega ye bataye pliz
Thunque sir ji v acchi hai
Thanks
Thanks sir ji
Good
Thanks
Bahut accha video hai Dost, Great information for diy users, Very neatly explained in details.
Plz tell value of Mov .
Just tell me if same can be used on Dob also.
Baki sab 1st Class hai.Thanks you
Thanks for your comment you can use 7d 511 ,mov in dov
bhaijee MOV ham kaise lagae ,i think mov is a asm command......garadge bhai ne kaha mov is a one kind of command...with love am amd.
sir aapne mov ko rectifier ke baad lagaya hai.kya transformer wale power suply main bi mov ko rectfier ke baad main laga sakte hai.maine 6 volt 0.5 amp ka power suply banaya hai.mere pass 7d 471 no.ka mov hai.plese reply.
Yes laga sakte he
@@A2Aelectronic DHANYAWAAD SIR.
Mov kitni value ke lagay
Thanqu so much🙏
Very good explaination ...but value of MOV not given please provide ...
7D511
thak you fir mov value
Very Well explained but one quarry left regarding after glow problem. Please let me know the value of resistance and mounting position . One more question regarding mounting of mov whether it is better used in ac section or in dc section. Should I use any pf like 474 j 450 volt in ac section for better protection after mov .
Your suitable reply will be highly appreciative.
Ramesh ji thanks for your valuable comment
Use mov in ac section, fusible resistance 100ohm to 47ohm .05 watt
Low glow led this is for 100ma led mcpcb ,if your led need more current use high value pf
@@A2Aelectronic lot of thanks for your prompt reply. Sir my question for after glow not for low glow. Please suggest the value of resistance which should be connected with output capacitor to prevent after glow problem.
NOT 127 V
@@A2Aelectronic Thanks for the practical circuit diagram. MOV shown after DC. Please explain the detailed calculation about choosing capacitor. The whole circuit works on the principles of capacitive Reactance formula. You used 155j 400v. Why not 105j, 225j, 335j? Yes, Please inform the output Voltage DC and it's Current capacity.
Awaiting your reply. 👍
A rc driver maximum keta mahina chalegi..j.m.roy.
3watt ke liye kya change karna padega circuit me?
3watt ke lie jo 22ohm ki resistance he uski value 47ohm to 100ohm Kar sakte ye led ki current pe depend karta he ye circuit 100mA ke lie he agar 3watt bulb me 100mA ki led use ki gai he to 22ohm ki resistance hi kaam karegi
good video
Thanks
MOV ka value Dena chahiye thaa.(07D511K) MOV DC side me lagaya, but similar MOV AC side me bhi lagana chahiye thaa. Because it's most important. and Filter capacitor velue is questionable.
100mfd
What is the voltage of capacitor??????
Mov should 07d471k is perfect...
Practical karke bhi dikhaiye
आप से निवेदन है कि आप pf दो लगाने को किस तरह से लगाना है दोनों की टांगों को एक साथ मिलकर लगाना है क्या
If 145j 400 volt not available which pf should use?
105/400v
Bhaiya Driver circuit atna chhota karke drawing karne se dekhne me dikkat hota hay, Kripaya thora barakarke drawing kariyega,
Ok
After bridge rectify voltage would be increased by 1.4 so usually voltage would be around 310 volt ...and use of electrolytic caps below voltage seems questionable ....does MOV adjust the volt there ???
MOV is only protection for spike ⚡ peak value is taken accordingly, which is 230x1.44. So capacitor value rating is 450v or 400v. Mov is used for protection against high voltage which becomes short circuit or burst and voltage cannot pass through further. Search for Capacitive Reactance formula in RUclips you will find details about the same. 👍
In diagram you showing mov is connect with DC current it is right or wrong? pls reply me?
second think you not show how many ohms discharge capacitor ? pls reply
You can use mov in ac input side
Fusible resistance can I use carbon film resistance 10ohms half watts in 9Watt led driver ?pls reply me
Use 47ohm but it's life no longer, use fusible for long life
@@A2Aelectronic thanks
Home made dropper cricket
12w15w18w keleye 22hom resistor hi lagers???????
Yes 22 ohm
Anwr khan
❤❤
Can I use pf 125j 400 volt with 100uf 100 volt capacitor but when I Seen dc voltage in multimeter it show only 59volt without 9watt led what reason voltage is showing very low?
Voltage should be 100v,something wrong in your circuit
@@A2Aelectronic ok sir I will check again
Thanks 9w pcb ap 12w pcb ka li kohi vidio banya
MOV ko AC side me lagna chahiye. Rectifier ke bad me nahi
Thanks
Thanks sir mere pass ek 7 led wala circuit h jisme afp224 0.22 micro farade ka capastor laga h jisme led glow nahi ho rahi h brize diode sahi kya problem ho sakti h
Ek ek karke sari led check karo
Ek ek karke sari led check karo
Led dropper
Its life is 3 months only..two led panel glow less
22uf to 100uf capacitor is
400 v?
100v
22Ohms registers nahi hai phir 100ohm/1w REGISTER lagayega chalega
2pcs 100 ohm ke resistance series me lagao
Sir ac and dc sarkid banae na
Ok
Rc led driver well
100volt capacitor fat jayega
me apka video dekhkar same 2 same banaya tha mgr mera output ka 22ohm ka resistance kuch second me fuk ja rha hai , mene 1 watt ka v lagaya wi thode der bad fuk ja rha h
. aisa q plz reply
Wire wound 2watt
Led drivers
Sir 155j do lagane par brightness kam ho ja rahi h plz bataye kya kiya jaye
22 ohm kam krdo ,sabse pahle 10ohm lo brightness bad jaegi
Sarkit ka name kya kya hai
Sir agar mcpcb karab ho jati hai us halat me 100v electrolyte condenser blast ho jayega uske bare me nahin bataya sir
Nahi blast hota he
50 w ka boley
Led bulb drivers
आप से निवेदन है कि12रा 12कि बैटरी चार्ज करने के लिए चलेगा क्या
????
Sir 22 watt LED tube light ka circuit ka video daliye please chote se chota ho
Ok
sir ye sara saman aap arrange kara sakte h mjh meri shop h mughe jarurt h
Sorry nahi arrange kar sakta
Aapne Diagram main MOV input ki bajay output main dikaya hai joki galat hai.kirpya diagram main thik karen.
Ok
Thanks for watching my vedio
50w led ke liye batalaye
Ok
Bridge Rectifier main out put mai to 220 volt dc aayega to vaha Filter Capacitor 100 volt ka kaise lage ga?
Vaha 400 ya 450 volt ka capacitor laga na pde ga na???
Voltage dropper circuit he iske series me 155j/400v capacitor laga he
@@A2Aelectronic Thanks
Fuse resistence burn ho rahi hey serese lamp glow hota hey kya karu
Kahi short circuit he diode check karo
Sir aap practical bana ker samjhatein toh samjh main ata diagram se banayein hain kaise samjh ayega
Sare circuit diagram se hi bante he naki practical , practical se keval simple circuit samjh me aa sakta he lekin jab circuit complicated hota he to aap vina diagram ke nahi bana sakte इसीलिए circuit diagram ko samjhna sikhie tabhi electonics me success honge aap video dekhne ke lie Thanks
@@A2Aelectronic ok sir
Sir जी 220vo Ac से100v DC कैसे बना या जाता है
Kaha use karna he
Rc driver ki life kitni hai
Depend on AC power supply agar supply fluctuate nahi hoti he to ic driver se zyda life hoti he
Mre q ek sir
Maine 155j 250 volt aur 10uf 250 volt use kiya tha do ghante ke baad smd led fuse ho gaya
22ohm ki rasistance use ki ,,mene jo circuit batya wahi banya aapne, is circuit ko me kafi din se use kar raha hu koi problem nahi hui
Sir y material kaha se mileage eska number dedo
Online mil jaega
Walue of M.O.V.??=??
Mov value 511k, Thanks for watching my vedio
Mov ka maan bataiye kya 511k ka hai
511
Sir brightness achi nahi mil rahi h
Rasistance 22ohm, use 10 ohm brightness bad jaegi mujhe lagta he aap jo led use kar rahe he high current MCPCB he , ye circuit 100ma MCPCB ke lie he Rasistance value kam karne se brightness bad jaegi
एक led लगाने मे 100 माइक्रो फेरेड का और दो led लगाने मे 22 माइक्रो फेरेडे का?!
Mov ,parelal होगा तो क्या मतलब।सीरीज मे होगा तभी मतलब का ।
??????
Sar RC driver ka aap photo bhej dete hamare pass ek ek components ke aaya apna WhatsApp number de dete
Video poora dekhe photo ki jaroorat nahi padegi
Sar mujhe components ke photo chahie
Components asani se kahi bhi mil jaenge
Nahin hamen to jarurat hai video to Puri dekh hi lenge aap photo bhej Sako to batao