I know this video is like a decade old but THANK YOU! Such a well made video, I was able to code my ABS module that had lost its soft coding in minutes! So thankful!!
@ my ABS light was on, used a VAGCOM reader to check codes, saw a message that the ABS module was incorrectly coded. So I performed this process to code it and the light went off
@mrhentrich I'm after putting a second hand abs pump and module into my car. Can not bled it as it won't let any fluid through the module and pedal keeps going to the floor
I have a 2004 Audi S4 v8 manual trans Vin 8E and I bought an abs module of ebay same part number and I'm using a snap on scanner, I can do everything in this video except the wcs code stays 0 while coding, it accepts the coding but I cannot change it wcs value it states its 0, it gives me the option to highlight it but it won't let me change the value, I wonder if it's the sp scanner limitation or the module, another thing I did find under special function I can find the wcs setting but it states it needs engineering login 4 digit code, I've been trying to get it programed it will not take the programming, or it will say function completed but as soon as i cycle key same errors come back I wonder if the wcs input being 0 is the issue?
I have Chevrolet Captiva AWD I HAVE ARRENGE ABS MODULE THAT ONE IS USED WITH SAME PART NUMBER NEED TO DO CODING WHEN I CLEAR WITH SCANNER FAULT LIGHTS OFF AFTER SUM TIME LIGHT GETS ON ( ABS ,HILL DOWN ASSIST, STEERING ANGLE, TRACTION CONTROL) NOW THIS LIGHTS ON PLEASE HELP WHAT CAN BE DONE OR SHOULD I GO FOR NEW MODULE
How over 400000 people viewed this video and didnt comment or like is crazy .... thank you this was exactly what i needed You have a very good voice for this kind of thing
I tried several times with vcds and hex kkl cable without succesces even though i could read all modules and could program other modules. After i tried the exact same procedure with a launch diagnostic tester and it worked. Probably some thing with to high latency
Witam a umnie jak wszedłem w kodowanie to kod już miałem zaakceptowany i nic nie musiałem kombinować więcej, sterownik zamieniłem o tych samych numerach co oryginalny, przejechałem się i sterownik sam się skalibrował z pompą i zaczęło działać ABS w Passacie B5.
I got a question for you, I’m trying to recode my abs module and I do everything step for step until the basic settings part because I have the unlicensed version, I enter the code but it won’t save, can I still code my module or do I have to pay $100 for the vcds lite license to access basic settings
This information will work with used Bosch 5.3 and 5.7 units. However... forums.ross-tech.com/index.php?threads/1997/ If you need support, we offer our customer free support on our web forum. forums.ross-tech.com
That's what I learned from your video. Go to the toilet before doing that all stuff. (Kidding 😆) Thanks for the coding procedure, very easy to understand step-by-step.
It accepts the coding for my Audi at first but next time I enter the ABS tab, the coding is back to 00000. The brake pressure says it’s above 290 bar and a fault code for the pressure sensor comes up. However, I checked the sensor using a multimeter and it seems to work as it should. Can someone please help?
when it says you have one minute to do the system test, one minute from when? when you start the car up? and also does vcds need to be connected to ecu while doing this or can you do it without?
+DJTOPKO The first two things that come to mind... a bad G85 sensor, or some one took the steering wheel of and then put it back on -75º off center, thus the G85 is now -75º off center. Get the G85 to read 0º, then pull the steering wheel off, recenter steering wheel, perform alignment, relearn G85. Send cases of L&P from New Zealand to Ross Tech office.
+RossTechVCDS Thank you very much for the answer. according to the owner noone done it. so might be faulty sensor then. Cant i just tell it with the vagcom where new 0° is? why i got to this, is because when you driving the car, brakes will come on on its own. never had problem like this before...
Hello! I need to replace my Bosch 5.7 ABS Module. The explanation in the video for login and coding is perfect, but: if I buy a used spare part without information in what car it was built in, do I need to know the original Login datas or can I use those, fitting to my car? Or is there a "general reset"?
When going with a used ABS module, first make sure the part numbers match up 100%. If the letter(s) at the end of the part number are different, they are not the same part. The coding of the ABS module is based on what it is currently installed in, not where it came from. Regards.
Hi! I'm a bit confused about your saying about matching up letter(s), because on my old Bosch 5.7 ABS module I found only numbers: 0265 950 012. I have used ABS module with same numbers: 0265 950 012 for replacing mine. But I can't see any letter(s) at the end. I'm not confident is it good match and I don't want proceed coding, before 100% sure it is right part. Thank you in advance, for reply.
Tried running the coding procedure several times on a 2004 Audi A4 Quattro 3.0. After entering the correct coding and login, still getting same 2 codes: 00778 Steering Angle Sensor, 01044 Control Module Incorrectly Coded. We purchased a used ABS module. Part numbers do match. Any ideas?
Ohhhhhh so the Workshop code WAS necessary… I always kept it at 00000 and was wondering why it wouldn’t save. That explains it, kinda weird but sure hahaha
Do: Pol Garage - Marek Szaniawski z Portsmouth - Heaathfield Rd, Unit 3: Mam 2 pytania, jeśli można: 1/ Czy te wszystkie etapy kodowania ABS Bosch 5.3 do 5.7 i modułów znajdujące się w Audi dotyczą także Audi A4 TDI, Anant, z roku 2005 ?. 2/ Czy w Pol Garage - Marek Szaniawski, mogę wymienić pasek rozrządu oraz lewy przegub ? Na odpowiedź czekam pod private address. Pozdrawiam :)
@@anzor4132 кароче включаеш субтитры нажми кнопку настроек там написано субтитри автоматически создано английский нажми и прогортай на низ там русский нажми и вуаля на русском
@@МихайлоРибіцький-ж4щ Спасибо за подсказку. Тоже самое, менял подрулевой шлейф, нужно было адаптировать с абс, спасибо ребята с драйва помогли, проблему уже решил. В моем случае нужно было коды прописывать по мимо манипуляций.
I know this video is like a decade old but THANK YOU! Such a well made video, I was able to code my ABS module that had lost its soft coding in minutes! So thankful!!
What do you mean by code your abs unit ?
I'm trying to figure out if coding your abs unit is the same as what I need to do
@ my ABS light was on, used a VAGCOM reader to check codes, saw a message that the ABS module was incorrectly coded. So I performed this process to code it and the light went off
@mrhentrich I'm after putting a second hand abs pump and module into my car. Can not bled it as it won't let any fluid through the module and pedal keeps going to the floor
You guys should be awarded with Nobel Peace Prizes.
VW And Audi said they can only do it. Thanks for your help done in 5 minutes.
Thank you ROSS TECH team. You helped me a lot. Best regards.
a company wich has humor. One thing i love about this company
Ross Tech, brilliant as always. Amazing video and explanation.
I have a 2004 Audi S4 v8 manual trans Vin 8E and I bought an abs module of ebay same part number and I'm using a snap on scanner, I can do everything in this video except the wcs code stays 0 while coding, it accepts the coding but I cannot change it wcs value it states its 0, it gives me the option to highlight it but it won't let me change the value, I wonder if it's the sp scanner limitation or the module, another thing I did find under special function I can find the wcs setting but it states it needs engineering login 4 digit code, I've been trying to get it programed it will not take the programming, or it will say function completed but as soon as i cycle key same errors come back I wonder if the wcs input being 0 is the issue?
¿video to recode module 8.0?
I have Chevrolet Captiva AWD I HAVE ARRENGE ABS MODULE THAT ONE IS USED WITH SAME PART NUMBER NEED TO DO CODING WHEN I CLEAR WITH SCANNER FAULT LIGHTS OFF AFTER SUM TIME LIGHT GETS ON ( ABS ,HILL DOWN ASSIST, STEERING ANGLE, TRACTION CONTROL) NOW THIS LIGHTS ON PLEASE HELP WHAT CAN BE DONE OR SHOULD I GO FOR NEW MODULE
For Skoda superb Wiki Ross tech link is inactive and I can't generate code ! Help!!
How over 400000 people viewed this video and didnt comment or like is crazy ....
thank you this was exactly what i needed
You have a very good voice for this kind of thing
To busy working
Después de coche entrar en varios talleres y salir con la misma avería me diste la solución funcionó perfecto sois los mejores
Great video . Now is there a video that can do the same for coding for the TCM and trans swap?
I tried several times with vcds and hex kkl cable without succesces even though i could read all modules and could program other modules.
After i tried the exact same procedure with a launch diagnostic tester and it worked. Probably some thing with to high latency
Witam a umnie jak wszedłem w kodowanie to kod już miałem zaakceptowany i nic nie musiałem kombinować więcej, sterownik zamieniłem o tych samych numerach co oryginalny, przejechałem się i sterownik sam się skalibrował z pompą i zaczęło działać ABS w Passacie B5.
I got a question for you, I’m trying to recode my abs module and I do everything step for step until the basic settings part because I have the unlicensed version, I enter the code but it won’t save, can I still code my module or do I have to pay $100 for the vcds lite license to access basic settings
Wondering the same thing here
I changed the wsc number to match the old module and now I can't communicate with it. How do I undo this action?
Tried to do it as shown not working for used unit. As my understanding it's only for new modules not used?
This information will work with used Bosch 5.3 and 5.7 units. However... forums.ross-tech.com/index.php?threads/1997/ If you need support, we offer our customer free support on our web forum. forums.ross-tech.com
It works also for skoda superb 1, 2.8 AMX. Of course login and coding is differenrt but procedure is same. Thx
That's what I learned from your video.
Go to the toilet before doing that all stuff.
(Kidding 😆)
Thanks for the coding procedure, very easy to understand step-by-step.
It accepts the coding for my Audi at first but next time I enter the ABS tab, the coding is back to 00000. The brake pressure says it’s above 290 bar and a fault code for the pressure sensor comes up. However, I checked the sensor using a multimeter and it seems to work as it should. Can someone please help?
We offer free vehicle support on our web forum for all of our registered customers. forums.ross-tech.com
If I change the automatic gearbox in manual gearbox, I will put the manual gearbox code,? Thank you.
What if after you type in the "login code" a dialog box comes up and says "no response from controler"?
when it says you have one minute to do the system test, one minute from when? when you start the car up? and also does vcds need to be connected to ecu while doing this or can you do it without?
Hello, I have errors of g85 00778 : 62-00 NO or incorrect adjustment00778: 37-00 defective. Someone can help thanks
Hello there. What if the Steering alignment has got "Not OK" ?
And for some reason when the steering wheel is straight its giving -75º
+DJTOPKO
The first two things that come to mind... a bad G85 sensor, or some one took the steering wheel of and then put it back on -75º off center, thus the G85 is now -75º off center. Get the G85 to read 0º, then pull the steering wheel off, recenter steering wheel, perform alignment, relearn G85. Send cases of L&P from New Zealand to Ross Tech office.
+RossTechVCDS Thank you very much for the answer. according to the owner noone done it. so might be faulty sensor then. Cant i just tell it with the vagcom where new 0° is?
why i got to this, is because when you driving the car, brakes will come on on its own. never had problem like this before...
Did u manage to fix the problem? I just recently replaced my G85 sensor. But I got the exact same problem as you.
My VCDS doesnt show which bosch sytem at top as suggested any ideas ?
Please use our free web forum for vehicle support. forums.ross-tech.com
How do you code Gateway and the codes
this is helpful video i liked and learnt something new
Hi, nice and informative video. For Audi the brakes code is 1LE you said, but for Skoda what would be the brake code?
Not all Audis have the same pr code. My A4 B6 Avant has the 1LT code
Hello! I need to replace my Bosch 5.7 ABS Module. The explanation in the video for login and coding is perfect, but: if I buy a used spare part without information in what car it was built in, do I need to know the original Login datas or can I use those, fitting to my car? Or is there a "general reset"?
When going with a used ABS module, first make sure the part numbers match up 100%. If the letter(s) at the end of the part number are different, they are not the same part. The coding of the ABS module is based on what it is currently installed in, not where it came from.
Regards.
Hi! I'm a bit confused about your saying about matching up letter(s), because on my old Bosch 5.7 ABS module I found only numbers: 0265 950 012. I have used ABS module with same numbers: 0265 950 012 for replacing mine. But I can't see any letter(s) at the end. I'm not confident is it good match and I don't want proceed coding, before 100% sure it is right part. Thank you in advance, for reply.
Tried running the coding procedure several times on a 2004 Audi A4 Quattro 3.0. After entering the correct coding and login, still getting same 2 codes: 00778 Steering Angle Sensor, 01044 Control Module Incorrectly Coded. We purchased a used ABS module. Part numbers do match. Any ideas?
tony gomes hello I have the same problem you !!!! how to solve ????
hello,is there any procedure tips for modules mk60? thank you Team
Does VCDS-Lite work to encode a 5.7 ABS Module? From an 2003 A6 4B C5, 2.5TDI Quattro ?
Yes, VCDS-Lite can be used as shown in this video, but you would have to purchase the full version, $99.
Do I have to recode the ABS when upgrading front brake system from 1LT to 1LX in 2002 A6?
what cable I need? vag-kkl?
My vcds login option not open helps
G85 37-00 faulty ?
Thank you so much ross tech
please do IT for polo 9n ABS
thank you. You saved me!
nice music.
Ohhhhhh so the Workshop code WAS necessary… I always kept it at 00000 and was wondering why it wouldn’t save. That explains it, kinda weird but sure hahaha
Muchas gracias! Me fue de gran ayuda!!!
Do: Pol Garage - Marek Szaniawski z Portsmouth - Heaathfield Rd, Unit 3:
Mam 2 pytania, jeśli można:
1/ Czy te wszystkie etapy kodowania ABS Bosch 5.3 do 5.7 i modułów znajdujące się w Audi dotyczą także Audi A4 TDI, Anant, z roku 2005 ?.
2/ Czy w Pol Garage - Marek Szaniawski, mogę wymienić pasek rozrządu oraz lewy przegub ?
Na odpowiedź czekam pod private address. Pozdrawiam :)
Hello, you are the best!!!!❤
Thanks! Good support!
thanks for the video ! it will me help a lot !
tried to sign in and subscribed would not work
You saved me!
its just too fucking complicated thats why i love my 405 turbo diesel
Super fu**in helpful!!! Thank you!!!
muchas gracias.
Superb!
meserieeeee exact ce trebuie
THANK YOU!!!!!!!!!!
thanks you
Love you !!!
Love u too
good
Плять, знать бы еще что он трындит!
субтитры в помощь
@@МихайлоРибіцький-ж4щ пытался, тоже на английском.
@@anzor4132 кароче включаеш субтитры нажми кнопку настроек там написано субтитри автоматически создано английский нажми и прогортай на низ там русский нажми и вуаля на русском
@@anzor4132 мне данный видос помог адаптировать блок абс на пассат б 5 хотя в английском я тоже не шарю
@@МихайлоРибіцький-ж4щ Спасибо за подсказку. Тоже самое, менял подрулевой шлейф, нужно было адаптировать с абс, спасибо ребята с драйва помогли, проблему уже решил. В моем случае нужно было коды прописывать по мимо манипуляций.
bom