Hello sir i have some adapters that they are 12v with 1 and 2 amps and as you said i have to use more volts... I have a power supply from laptop that is 19v but with 4.35 or 3.8amps what i have to do to make a battery charger to have my motorcycle battery normal for the winter
Dear friend, I have carried out the project following the steps and components as you detail, but when I connect it to the transformer of my charger, which has 15.5 volt output, the relay cuts off and it is impossible for me to charge the battery, watching the video where it You do the test, I see that when the source sends 14.9 V, the relay cuts off, but it is cutting off due to the increase in voltage of the source, not because of the increase in battery voltage, since if I inject a voltage of 14.0 volts through the output to the battery, the relay makes a noise and never cuts off. You don't show how much voltage you are supplying to the battery... reasoning, you should power the board with less than 14.9 volts so that the relay does not cut, therefore the battery will never exceed that voltage and in that case it would never cut.
Ola amigo boa tarde gosto muito dos seus progetos para mim que não estudei eletronica admiro esse ramo e fasso alguns circuitos so de curioso mas tenho uma perfunta esse circuito desliga quando a bateria estiver carregada correto mas qual a voltagem de entrada dc maxima no circuito Obrigado
@@ZAFERYILDIZ52 teşekkürler dönüş için 12 volt boşta adaptörlerim var normal kuru aküyü şarj için yeterli olur mu bu devre ile? ya da kaç amper minimum güç lazım?
15 volts and a charging current of 10/1 of the current of the battery you will charge is ideal and healthy. For example, 1 ampere charging current for a 10 amp battery.
There is an error in the circuit diagram. The diode anode must be connected to the normally closed contacts of the relay.
Nice circuit works well , I’ve built it with 1:4 watt resistors, but tell me 4:55 What wattage are the resistors in your setup
Great job 👍 watching from Chad 🇷🇴
Why chad copied romania flag?
Thank you very much Chad, love
You are welcome
Hello sir i have some adapters that they are 12v with 1 and 2 amps and as you said i have to use more volts... I have a power supply from laptop that is 19v but with 4.35 or 3.8amps what i have to do to make a battery charger to have my motorcycle battery normal for the winter
The worlds best teacher thanks sir
sir, which relay did you used for this project?
Sr zafer, si conecto la batería invertida por error, como protejo el circuito?...gracias.
Eline diline sağlık Üstad
Mano, top demais essa indicador. parabéns. Vou fazer um pra mim
Zafer kardeşim çok güzel bir devre olmuş eline sağlık👍
yorum ve destek için ben teşekkür ederim
Buen proyecto, lo felicito y gracias por compartir!!!... 👍👍
Gracias por sus lindos comentarios y apoyo.
your video montage is fantastic
Thank you very much
Amigo lo felicito, una pregunta, que voltaje usa el Buzzer... Gracias
Hi, there is a connection missing on the TL431, and the Electrolytic Cap is not included in the drawing, Good project!
👌
Mr. Zafer , may be can we request about indicator charging and full charging of BMS(Battery Management System).
Thank you
If I have the opportunity, I can make a BMS this month, a circuit based on PCB.
Saludos una pregunta que amperaje usa ese cargador para cargar la bateria
I am wondering the voltage reached more than 14v. Is it ok for 12v battery?
PREGUNTO QUE TIEMPO SUENA EL BUZZER, CUNDO ESTA COMPLETA DE CARGA LA BATERIA
EXELENTE!!!👍👌 MUY BUENA INGENIERIA MI ESTIMADO!!! SIRVE PARA BATERIA DE AUTO?.BENDICIONES!!!
Super 😊😊😊👍👍👍
Estes teus vídeos artigos são muito interessantes, e impressionante as aulas de eletrônica nos vídeos, artigos coisa de profissional 🎉🎉🎉
verdade, mas seria melho cortar automaticamente ao invés de ativar o buzzer
Thank you for the comment and support.
What is the maximum current that this circuit supports ?
Could you please make the PCB?
Sagh ol
60 amperlik araba akusuna olurmu?
Giris votas kac volt?
Thank you. The clip image is very nice, unfortunately there is no circuit diagram
Dear friend, I have carried out the project following the steps and components as you detail, but when I connect it to the transformer of my charger, which has 15.5 volt output, the relay cuts off and it is impossible for me to charge the battery, watching the video where it You do the test, I see that when the source sends 14.9 V, the relay cuts off, but it is cutting off due to the increase in voltage of the source, not because of the increase in battery voltage, since if I inject a voltage of 14.0 volts through the output to the battery, the relay makes a noise and never cuts off. You don't show how much voltage you are supplying to the battery... reasoning, you should power the board with less than 14.9 volts so that the relay does not cut, therefore the battery will never exceed that voltage and in that case it would never cut.
Kolay gelsin ellerine sağlık hocam giriş voltajı nedir
Why is the relay chattering at near cutoff voltage
Ola amigo boa tarde gosto muito dos seus progetos para mim que não estudei eletronica admiro esse ramo e fasso alguns circuitos so de curioso mas tenho uma perfunta esse circuito desliga quando a bateria estiver carregada correto mas qual a voltagem de entrada dc maxima no circuito Obrigado
Is it good for a lithium 12 v battery?
Sir how many volts in the buzzer
Akan saya praktekan
В принципиальной схеме ошибка. Анод диода нужно подключить к нормально замкнутым контактам реле.
Zafer hocam eline sağlık son kısımda dolumun ne kadar süre tuttuğunu yazsaydın güzel olurdu
akünün durumuna göre degişir bu ve kapasitrsine göre ayrıca şarj için kullanılan güç kaynagıda önem arz eder bu nedenle süre belirtmedim
@@ZAFERYILDIZ52 teşekkürler dönüş için 12 volt boşta adaptörlerim var normal kuru aküyü şarj için yeterli olur mu bu devre ile? ya da kaç amper minimum güç lazım?
Bro plz make same circuit for 4.2v lithium battery
Charger with auto cut
vere good ❤❤
nice
thx my friend
Zafer bey çalişmalarınızı takip ediyorum 10voltluk zener kullansak olurmu köydeyiz ha diyince elimizde olmuyor parçalar teşekkür ederim
Can we use this for 12v 100AH battery
YES
I want a circuit diagram
انت فنان شكرا لك
شكرا لتعليقك ودعمك.
Здравствуйте. Можно ли эту зарядку использовать для автомобильных аккумуляторов?
Да, можно заряжать аккумуляторы емкостью до 100 мАч входным током 10 Ампер.
Hi Zafer. What input current does the circuit need to operate and charge the battery? 12v or more? Does the relay work with 12v? Thanks
Relay use 12V, voltage to charge is 13,5V or 13,8V
@@CarlosdoRS Thanks Carlos
15 volts and a charging current of 10/1 of the current of the battery you will charge is ideal and healthy. For example, 1 ampere charging current for a 10 amp battery.
درود بر شما آقای مهندس
Yahi circuit 4.2 volt lithium battery ke liye bnao with auto cut
👌
@@ZAFERYILDIZ52 bro please make same circuit for 4.2v lithium battery charger with auto cut
Without ic transistor using
Cam bu çekimlerde kullandığın kamera marka model nedir.
ticari sır :)
звуковая индикация правильно светодиоды красный с зелёным поменять местами
amazing
thx my friend
nice amazing
thank you my friend
Brother same circuit 6v battery charger please request 🙏
👌
Una pregunta ese sircuito se coloca en las salidas del cargador
elinize sağlık
Vous n avez pas indiquer la tension d entrée !!!
สุดยอดเลยครับ
Manda o esquema para mim com a referência das peças
şemayı kontrol edermisin eksiklik var tl431 de
👌
Схема не закончена , но идея приемлема если ток заряда ограничен.
Bu devrenin fiyatı ne kadar
ขอบคุณมากครับ
ขอบคุณสำหรับการสนับสนุนและความคิดเห็นที่ดีของคุณ
Merhaba hocam devreyi yaparken kullandığınız o telin adı ne nereden bulabiliriz.
lehim teli mi yoksa tek damar kablomu ?
👍❤️❤️❤️❤️👍
👉❤👈
el diagrama no cincide
Dear Zafar, I need a video of making a simple water level with 12 volt relay
👍👍👍👍👍
👌❤
Maksimum kaç amper kaldırır
10 amper sarj akımı mümkün
Ótimo?
Buat rangkaian pengisian baterai 12 volt, auto cut yang ditentukan oleh arus listrik (ampere) bukan oleh Tenganan listrik(voltase). terimakasih.
Benar, menurut mas e gimana tentang rangkaian dan praktek dari video diatas 🙏
@@humanlive6516 sama seperti vidio vidio yang lalu, ditentukan oleh tegangan listriknya atau voltase listrik bukan oleh arus listrik atau ampere nya 🙏
Ya itu bisa dilakukan tapi ini adalah alternatif
👍
❤❤
50v auto kat charket charjig
👍👏👏
👉❤👈
❤
❤
ان مكن مخطط الدائرة
Devre şeması açıklamalar bölümünde var
👌👏👏🙏🙏💐
Work nahi karti
Like
👉❤👈
Звук никому не нужен, лучше реле отключения ставить.
Иногда полезно добавить для тех, кто хочет следить
Zafer, вы самый полезный самодельщик в ютубе !!._ : )
Бывают ошибки, но идеи у Вас очень хорошие.
nice amazing💫💥💯💚🤍❤💯💥💫
สุดยอดเลยครับ
👍👍👍👍👍
👉❤👈
❤❤❤