I m from Bangladesh. when i rewinding a coil that time i realy very enjoying its beutiful work. after work done a cup of tea me & my mind feel very cool. my dreem is to working foreign country like your workshop sir.
سلام جناب همدانی گرامی لبه های این قالب هارو کمی شیب دار درست میکنیم .بخاطر همینه که سیمها به راحتی از روی قالب در میاد. ممنون که ما رو دنبال میکنید و دقت نظر دارید و نظراتتون رو با ما به اشتراک میگذارید
A lot of man hours goes into rewinding. Do you already know the coil configuration before stripping the coils. Is rewinding cheaper than buying new motor?
Hello, dear friend, thank you for your comment about our work. In our country, Iran, because we are embargoed by other countries, repairing electric motors is much cheaper than buying a new electric motor.
It is good job and I Also Start rewindig But I am not good sikll so pleas explan in detial specaily how to count the slot and how to out the terminal wire pleas
Hello, thank you for watching our video. The number of phases is written on the motor plate, and the number of poles is obtained from the speed of the electric motor written on the plate with the formula of speed, pole and frequency, for example, 3000 revolutions with 2 poles, 1500 with 4 poles. 1000 turns has 6 poles and the rest of the electromotor calculations are taken from the previous winding
Thank you so much! I use to rewind small motors way back when I was able to. Only I did it my way cause I can not compute. I've done good though then. Thanks again!.
ممنونم آقا مهدی گل باعث افتخاره که ما رو دنبال میکنید . جسارتا میخواستم بپرسم آیا شما هم در زمینه سیم پیچی فعالیت دارید؟ و اینکه کجای ایران تشریف دارید؟
Hello sir my name is hassan ahmed and i am speaking from assam sir i have mfd20kaipesitar 1hp motor 24slot.rpm2800 ampr5.0. how to do coil data entry? please give me some notes. i am not able to understand it, please
@@coil_magnet Am from Ethiopia I want to start this work in Ethiopia. So if you can support me by knowledge. Pls make answer to my question. Question . If a coil wire thickness are 1mm and I will have no that wire thickness what I will do? I know. We can change wire thickness to another. But I do not know how to
@@YaredWorkneh-eg3tn You have to calculate the cross-sectional area of the wire or the area of the circle with a diameter of 1 mm, then replace two or more wires whose cross-sectional area is equal to it.
Hello, what a great job! What country are you from? I’m from Brazil and I have an engine rewinding company as well. I am getting to know better the countries that still have this valued profession, for who knows one day to migrate and set up something like that.
Just one negative point that he did not pull up first coils and done the open winding,if he done that then the winding shape was going to be very good and quality work.
@@vishalrasane1392 Thank you for your message full of energy. Thank you for following us. I hope our videos get better every day and are useful for our friends
Hi would you get many rewinds to do in Northern Ireland there isn't many who do it I know one company called Hugh J Scotts they used to manufactor Motors AC/DC they dont have a rewind shop today you do a good job I found it hard to internally connect the coil ends in the right order based on the number pairs of poles
Hello, Mr. Rohit, I am glad to meet you. It is an honor that you are following us. I also started with small electric motors and over time my experience increased. You will surely become a very good coiler one day and you will coil very large electric motors.
Why doesn’t anyone use a simple cutting wheel to cut out the crown instead of a hammer and chisel that destroys your hands and bangs up the stater housing ?? I don’t get it.
I am from Sri Lanka .I began motor winding work s in 1994 this year .is 30th anniversary
Hello, dear friend, I am happy to meet you. You are very experienced in this work. I would be happy if you have any comments about our work.
Motor rewinders are great job
Hi thank you very much. Where are you from? What's your job?
@@coil_magnetovosu asinhrovani elektro motori velike snage
🙋🇧🇦
Very professionally done...
Tank you so much bro🙏🙏🙏
سلام .بهترین راه برا پاک کردن شیارهایی که آشغالاش در نمی آیند چیه؟
Привет мне как обмотчику приятно видеть хорошую работу Эта мастерская от завода или частная успехов в труде
Tank you so much
I m from Bangladesh.
when i rewinding a coil that time i realy very enjoying its beutiful work.
after work done a cup of tea me & my mind feel very cool.
my dreem is to working foreign country like your workshop sir.
Nice to meet you bro. I'm from Iran. I completely agree with what you said. We are proud that you follow us. Thank you for your energetic message.
I'am from 🇮🇩 Indonesia, why motor or Alternator 628 kva , after winding high temp. To body. ? 2:42 ....tank verymuch sir .
استاد اسم اون رنگ قرمزی که بهش زدید چیه
سلام وقت بخیر نوعی عایق هست که برای الکتروموتورهای MV و LV استفاده میشود
عالی بود
ممنون از لطف شما جناب اله یاری گرامی🙏🙏🙏
کارتون عالی ولی جالبه این قالب چطوره اینقدر راحت در میاد. سیما از روش
سلام جناب همدانی گرامی
لبه های این قالب هارو کمی شیب دار درست میکنیم .بخاطر همینه که سیمها به راحتی از روی قالب در میاد.
ممنون که ما رو دنبال میکنید و دقت نظر دارید و نظراتتون رو با ما به اشتراک میگذارید
@@coil_magnet شبیه به همینو ولی ما توی شناور دارین به همین روش با چوب درست کردیم واس اونا راحت میاد
عالی بود ، میشه بگید این کارگاه کجاست ؟
سلام دوست عزیز خیلی ممنونم بابت پیام دلگرم کنندگان.ما تهران هستیم .شما کجا تشریف دارید؟
کانال شما راجع به ریخته گریه درسته؟
Parabéns pelo trabalho de vocês abraços.
Tank you so much🙏🙏🙏
Very nice vdo thanks
Thank you very much
you work very well
Tank you 🙏🙏🙏
A lot of man hours goes into rewinding. Do you already know the coil configuration before stripping the coils. Is rewinding cheaper than buying new motor?
Hello, dear friend, thank you for your comment about our work. In our country, Iran, because we are embargoed by other countries, repairing electric motors is much cheaper than buying a new electric motor.
Bon travail
Bonjour cher Monsieur Ahmad, merci beaucoup de nous suivre et de nous encourager avec votre message.
Good job
Каким лаком пользуетесь?
It is good job and I Also Start rewindig But I am not good sikll so pleas explan in detial specaily how to count the slot and how to out the terminal wire pleas
Very good job respect and love from India🇮🇳❤
Tanks bro. Are you a motor winder?
@@coil_magnet yes my dear brother
@@firozjamani8218 nice to meet you
how do you know the number of poles, number of turns and phases. thank you
Hello, thank you for watching our video. The number of phases is written on the motor plate, and the number of poles is obtained from the speed of the electric motor written on the plate with the formula of speed, pole and frequency, for example, 3000 revolutions with 2 poles, 1500 with 4 poles. 1000 turns has 6 poles and the rest of the electromotor calculations are taken from the previous winding
@@coil_magnetneat winding too, thank you
how do you price the rewind? thank you.
Brother, I have been learning motor refining work for two years and I am telling you from Bangladesh to take me a little
Thank you so much! I use to rewind small motors way back when I was able to. Only I did it my way cause I can not compute. I've done good though then. Thanks again!.
That's great
Where are you from?
@@coil_magnet phillipines.
@@coil_magnetI want to talk to you
عالی بود کارتون ❤
ممنونم آقا مهدی گل
باعث افتخاره که ما رو دنبال میکنید .
جسارتا میخواستم بپرسم آیا شما هم در زمینه سیم پیچی فعالیت دارید؟ و اینکه کجای ایران تشریف دارید؟
দারুণ
Tank you so much
Good work
Tanks bro
@@coil_magnet want to talk to you bro
@@coil_magnet where are you from
@@MDSUJON-mu9jv I'm from Iran and you?
👏👏👌👌👍👍🇧🇷
Hello sir my name is hassan ahmed and i am speaking from assam sir i have mfd20kaipesitar 1hp motor 24slot.rpm2800 ampr5.0. how to do coil data entry? please give me some notes. i am not able to understand it, please
How many mm wire size
3×1.10mm
1.15mm
1.25mm
1.30mm
I have one question sir
I can ask?
Yes of course
@@coil_magnet
Am from Ethiopia
I want to start this work in Ethiopia.
So if you can support me by knowledge. Pls make answer to my question.
Question .
If a coil wire thickness are 1mm and I will have no that wire thickness what I will do?
I know. We can change wire thickness to another. But I do not know how to
@@YaredWorkneh-eg3tn You have to calculate the cross-sectional area of the wire or the area of the circle with a diameter of 1 mm, then replace two or more wires whose cross-sectional area is equal to it.
@@coil_magnet
How
You will show to me
Calculation?
Or you have book about this
Can I work as is job
Great job ❤❤❤
I love this work
Hello 👋
hello 👋
Good
Thank you very much Mr bagal. Where are you from?
Hello, what a great job! What country are you from? I’m from Brazil and I have an engine rewinding company as well. I am getting to know better the countries that still have this valued profession, for who knows one day to migrate and set up something like that.
Nice to meet you bro .I'm from Iran
Nice to meet you bro. I'm from Iran
Geniál saludos desde Buenaventúra colombia
Ở Việt Nam vẫn còn những công việc như vậy
❤❤❤❤
جناب محمدی ممنون که ما رو دنبال میکنید🙏🙏🙏
Just one negative point that he did not pull up first coils and done the open winding,if he done that then the winding shape was going to be very good and quality work.
Tank you so much
@@coil_magnet Your work and experience is good,like the video,thank you for the knowledge.
@@vishalrasane1392 Thank you for your message full of energy. Thank you for following us. I hope our videos get better every day and are useful for our friends
Guru ji chan Rewarding nhi hua ek Koyal isase koi problem to nahin hoga mujhe kament karke bataya sir
Gandi winding half coil uthana chahiye dekhne me bhi achcha rotar dalne me koi pareshani nahi hogi
I work in a company and I want to open my own workshop
I hope you are very successful in the cartoon
Hi would you get many rewinds to do in Northern Ireland there isn't many who do it I know one company called Hugh J Scotts they used to manufactor Motors AC/DC they dont have a rewind shop today you do a good job I found it hard to internally connect the coil ends in the right order based on the number pairs of poles
👍👍👍
Can you give the fertilizer diagram please
Hello brother, I did not understand what you mean. If you explain more, I will definitely do it for you.
Actually he meant the diagram of coil connection with each other, the series connection by which you brought 6 input terminal
三相异步电动机 我也会缠电机。 😂
Konse desh me bana rahe hain
Plz sir share Connection Diagram
Hello, please send me your Telegram ID so that I can send you the connection diagram
I visited your channel, why haven't you uploaded a video for a long time? Where are you from?
@@coil_magnetwhere is your shop
I am a new winder I love winding Big motor work is not available where I work. I want to work on big motor and learn to work..
Hello, Mr. Rohit, I am glad to meet you. It is an honor that you are following us. I also started with small electric motors and over time my experience increased. You will surely become a very good coiler one day and you will coil very large electric motors.
Please watch our videos, there are good tips to learn in the videos.
Thank you .
@@coil_magnet thank you so much sir where is your work shop and name of the work shop
you're welcome . Our company is in Iran. And the name of the company is coil magnet.
@@rohitmajumder1144 where do you live bro?
Hello sir
this winding is star delta . need star delta starter panel .
Sir mujh bhi kam karni. M acha lagta hi par dc motor ka rodar m piromlam ati hi
I don't understand your language. Please speak English
Mai ap ke company kam Krna chahti sir
Can you please share the connection diagram with me please
Hello, I will leave my phone number for you. Send me a message on WhatsApp tomorrow and I will send it to you
+989192151297
Hi
Sir mere ko kam chahiye
Hi bro how can I help you
S.W.G.তাৱ কত tonকত দূৱত কত কয় সেট কয়েল
Can you at least give us more details?
Dear Arthur, if you need any information, tell me and I will send it to you via Telegram or WhatsApp
Why doesn’t anyone use a simple cutting wheel to cut out the crown instead of a hammer and chisel that destroys your hands and bangs up the stater housing ?? I don’t get it.
Hello, dear friend, thank you for your support. You are absolutely right
Hello Sri job milega
6 parallel star Delta
Space cyber monkey shit. It’s archaic yet …from the Gawdam future
Hi bro
85kg
Hlo sir
Hi 👋
I don't believe that it can produces 200kv
This is a 200kw electric motor, it does not generate voltage
@@coil_magnet Thanks for the response 😊
I want to talk to you
Hello dear friend, how can I help you?
No guidepaper
Hello, dear friend and companion, what do you say the guide paper is for?
.
At last u waste you are varnish so much , that's not good 😢
ruclips.net/video/vyBbY5l7sgk/видео.html
Please job sir
Where are you from?
200kW? Blbost...
❤❤❤