Thank you for the video! I was at work and I was going to quick adjust them but figured I could clean them and when I took the blade of the spring went flying off. Your video helped a lot. The brown piece on mine didn’t stay put like yours though so I just held it down and put the other blade on top. It works perfectly fine now.
man i have been on here for hours trying to figure out to get this pin thing back in, i aint lying.... i have the knockoff chj 908 but same design and they have no videos addressing that issue... syncronization
Thank you so much for this!!! I took mine apart and the spring came out, I was freaking out worried they were done for, this is the only video I could find showing me how to put it back in correctly!
Yoooo...don't do half the shit he does...you don't have to pry anything apart...the chrome piece on front use ur thumb press in an push up....how u gonna forget the bottom screws if u do maintenance every 2 or 3 days??? Again don't pry anything apart it all comes off by hand After u remove the screws
Thanks for the video bro. I was struggling with the spring like 30minutes trying to figure out how to put it back properly. I've searched the other videos by other RUclipsrs. But so far I didn't find any of them show how to place the spring. Thanks a lot.
Same, i figured out everything but the spring part because I accident popped it out before knowing where it went. look at 10:40 for anyone who forgot how
I have 2 of these. I have coarse Asian Hair and fade my hair tight to the skin. But with the staggered tooth blade it puts vertical lines on my hair. I changed my other magic clips blades to a taper blade and it's all good . Might throw on my senior blades to replace the staggered tooth ones. Corderless seniors lol and that even out in the U.S yet. The magic clips are amazing. Thanks for the vid.
No offense but you might want to practice taking the Clippers apart and putting them together correctly a few times before you make the video. You're doing everything backwards and damaging the Clippers at the same time. Also, with your camera mounted on the side we can't see what you're doing most of the time. A Viewpoint from above would be much better for this type of video. Peace
I suggest using lithium grease on electrical switches instead of oil . It has a higher viscosity and will not break down as quickly. A small amount goes a long way!
Hiya, any chance u could show me how to fix the lever as mine is not grabbing anymore and it wont turn on . Goes on and off and its not grabbing but i cant see it properly in the vid :) many thanks :)
is the plastic peace that sits over the spring supposed to shoot off into the air when you remove it? because I gotta duck n cover each time I go to clean my clippers
Joseph Alejos No problem mate. Also I would but I don't have social media. If I decide to IG, I'll be sure to follow you. PS. I'm 20 so yeah I get that it's a bit unusual for me not to own social media
I have a pair of seniors they look the same when taking off the blades etc.when I put them back together they don’t cut.is there a way of putting the black plastic piece that the smaller blade fits on A certain way. Cheers
Is the metal piece that goes up and down,suppose to be under the black clip that snaps in or is the black clip suppose to rest on top of the metal piece?
Check to see if the housing of the clipper is not broken. The part were the lever is at make sure that its not cracked or stressed from the lever itself
Very helpful tutorial, BTW my question is about my new magic clip, so I notice there is a movement on the upper blade(cutting blade) every time I turn it on or off the cutting blade is a little on the left side or right side, it doesn't stay in the center since my old clippers are not like that, do you think is that normal or should I change it?
Its normal it stops were ever the blade is when you turn off the clippers some time the blade will be to the right or left even the center depending on when you turn off the clipper
I have some brand new straight out of the box, cordless magic clips. I took the blades off to replace with a ceramic blade now they won't turn back on. Do you have a remedy?
Try taking off the blade and all the little pieces as well then try to turn them on if it doesn't turn on then it might be a issue with the switch or the battery might be no good but that is a slight possibility since you just took them out the box
@@MrXxtoshixx what helps if you place spring one the clipper them place the brown part on the cutting blade line up the Rotary motor to the center of the Brown bees then hold the blade from the sides then place fade blade on top using the top and back remove fingers that's holding the cutting blade place screw on the fade blade then the other then from there it should be good to let go but dont tighten all the way. This give you time to let go off the cutting blade and be able to adjust the fade blade as you please then once you find the sweet spot tighten up the screws then you should be golden
The piece that you our on top of the spring keeps popping out, will not stay in place, and when I use the level for open to close it will not stay under the bridge.
Yani Mendoza I might be able to help do you have Instagram if so send me a picture of your clipper with the prob so I can get an idea of ways going on with it. and I'll try to help you with the best of knowledge IG: joefade_
Do you know what’s the name of that Small plastic that holds the blade? Mine broke and I don’t know where to get it from or what is called. Thank you so much
Jolie Mendoza check on eBay with Harley Barber Supply they might carry it. I don't know the name but it could be call the blade holder or the moving blade holder I'm not sure
Alexis Zarate can you dm a picture of the brown part to my Instagram. if so the IG name is @joefade_ I just want to check if it's broken or cracked in a place that maybe it's not catching when your placing it back on the clipper
AzNwacko how you doing brother sorry I just seeing your comment to do that to make sure that the screw is back in position for when you tighten it. You might have to use like a small Flathead to kind of keep the the nut half in place while tightening and once you tighten it should catch and it should tighten up from there
no worries i fixed the issue, i had to re-order the washer, that helps screw the lever in tight, its a silver washer that you slide into the back part of the clipper.
11:46 bro you said it would fly out mine flew out and now when I try to put it back it it wont stay the spring pushes it out and it dosnt stay without me holding on to it
Okay put the spring on, then brown part on cutting blade then line up the rotor to the center of the brown part(holding the side of the cutting blade with your thumb and index finger) place the fade blade on top( holding with thumb on the bottom of blade and index finger on top on the teeth part of the fasde blade) release your thumb and index from cutting blade. Now place one screw on your fade blade then place the other line up your blade then tighten that should fix your problem
@@josephalejos5443 yup NP bro I have a YT channel too 💪 we're in the same bro I'll make sure to hyu if I have any questions like I said good looking out💪 and thank you for the great content ma boii stay up 😎💪
Hey man thanks for putting this video up. Helped alot. One problem I'm having is the brown plastic piece keeps popping out every time I try and screw the lever back on. Any idea why this is happening? Pretty frustrating because I feel like I've tried everything.
mine dont want to charge, works with the cord on but doesnt want to charge , you know anything bout that can help me ?, and my bottom blade move side ways
Mitch 81 another way to do it is if you put the cutting blade on the brown piece and then attach it back to the spring you'll be able to use your thumb and your index finger to hold it down theb place in the fade blade on top and then from there you'll put your screw on and then you'll be able to move your fingers and adjust the fade blade to the needed zero-gap then at that moment the brown piece will no longer pop off since the fade blade will be holding it
Christopher Diaz okay, umm if you put the moving blade on the brown piece to hold in place the put your bottom blade on it then hold it down . Then place one screw to hold the blade then form there set the second and it should be good to go
If the spring ever pop out hy accident and you forget how to put it back, around 10:40 shows you how
It happened to me .. I dont know to to set back the inside properly .. Plzzzz help
Exactly what I needed thanks bro
Exactly what I needed thanks bro
Thanks! It’s so tricky
You are a fucking life saver
Thank you for the video! I was at work and I was going to quick adjust them but figured I could clean them and when I took the blade of the spring went flying off. Your video helped a lot. The brown piece on mine didn’t stay put like yours though so I just held it down and put the other blade on top. It works perfectly fine now.
Alexa Cortez I'm glad it could help you!! Thank you for watching
man i have been on here for hours trying to figure out to get this pin thing back in, i aint lying.... i have the knockoff chj 908 but same design and they have no videos addressing that issue... syncronization
Thank you so much for this!!! I took mine apart and the spring came out, I was freaking out worried they were done for, this is the only video I could find showing me how to put it back in correctly!
Yoooo...don't do half the shit he does...you don't have to pry anything apart...the chrome piece on front use ur thumb press in an push up....how u gonna forget the bottom screws if u do maintenance every 2 or 3 days??? Again don't pry anything apart it all comes off by hand After u remove the screws
Thanks for the video bro. I was struggling with the spring like 30minutes trying to figure out how to put it back properly. I've searched the other videos by other RUclipsrs. But so far I didn't find any of them show how to place the spring. Thanks a lot.
Same, i figured out everything but the spring part because I accident popped it out before knowing where it went. look at 10:40 for anyone who forgot how
That shit hit me in the eye
😂
Thanks for the video bro, you saved me! lol
Marcos Fonseca thank you for watching
Appreciate this video yo , very detailed 🙏
Aggi Resendiz I appreciate the complement brotha, thanks for watching
I have 2 of these. I have coarse Asian Hair and fade my hair tight to the skin. But with the staggered tooth blade it puts vertical lines on my hair. I changed my other magic clips blades to a taper blade and it's all good . Might throw on my senior blades to replace the staggered tooth ones. Corderless seniors lol and that even out in the U.S yet. The magic clips are amazing. Thanks for the vid.
Mark Navarro thanks for watching brotha
hey i have a question, do you have any fix for the springs shooting out while trying to reassemble the blade
No offense but you might want to practice taking the Clippers apart and putting them together correctly a few times before you make the video. You're doing everything backwards and damaging the Clippers at the same time. Also, with your camera mounted on the side we can't see what you're doing most of the time. A Viewpoint from above would be much better for this type of video. Peace
Thank you for watching
the black plastic top won’t stay in place for me it keeps popping out any help ?
If you put that price on the top cutting bland them match the blk part to the rotor then place the fade blade on top it should work that way
Thanks this vidio saved me when the spring pooped out not how I would have put it back together
Glad it helped
I suggest using lithium grease on electrical switches instead of oil . It has a higher viscosity and will not break down as quickly. A small amount goes a long way!
Thank you I look into it!!
@ony1952 what grease do you use for the mute switch
anyone have an issue where the cutter blade slides left and right when turned on???
Thank you! I thought I surely lost a piece, turns out I didn't!
Hiya, any chance u could show me how to fix the lever as mine is not grabbing anymore and it wont turn on . Goes on and off and its not grabbing but i cant see it properly in the vid :) many thanks :)
Thank you!
THANK YOU SO MUCH I FIX MY CLIPER SO GOOD
is the plastic peace that sits over the spring supposed to shoot off into the air when you remove it? because I gotta duck n cover each time I go to clean my clippers
Itll help if you have your lever set to close after you put on the brown piece there's a part on the back side that stays under the slide bar
Got everything but the little magnet where does it go?
thanks for the instruction. very helpful
This video was very helpful. Thank you.
Lazy thank you for watching. Please follow me on IG. @Joefade_
Joseph Alejos
No problem mate.
Also I would but I don't have social media. If I decide to IG, I'll be sure to follow you.
PS. I'm 20 so yeah I get that it's a bit unusual for me not to own social media
I have a pair of seniors they look the same when taking off the blades etc.when I put them back together they don’t cut.is there a way of putting the black plastic piece that the smaller blade fits on
A certain way. Cheers
The red top doesn't come off how did you get it off so easily
Is the metal piece that goes up and down,suppose to be under the black clip that snaps in or is the black clip suppose to rest on top of the metal piece?
The bar that hold the bottom blade will hold the clip down
@@josephalejos5443 thanks ! Watched your other video and figured it out. Thanks for the quick reply.
Easy good tutorial ! 👍😊✔
hey bro when i open the lever the blade is not straight when closed it is but when i open it it kind of goes a little bit to the side why is that?
Check to see if the housing of the clipper is not broken. The part were the lever is at make sure that its not cracked or stressed from the lever itself
Thank you bro
What is the black plastic part that holds the moving blade called? And where can I buy one? Mine broke 🤦🏽♂️ anybody know?
telloprofesional.com/gb/accessories-and-replacements/replacement-support-blade-cordless-magic-clip-wahl-12964-4015110018643.html
Great 'how to' video!
Thanks 👌👌
Thank you for watching 😁
Very helpful tutorial, BTW my question is about my new magic clip, so I notice there is a movement on the upper blade(cutting blade) every time I turn it on or off the cutting blade is a little on the left side or right side, it doesn't stay in the center since my old clippers are not like that, do you think is that normal or should I change it?
Its normal it stops were ever the blade is when you turn off the clippers some time the blade will be to the right or left even the center depending on when you turn off the clipper
@@josephalejos5443 is it because of rotary motors or what?
@@shapourh6516 yes its cause its rotary
@@josephalejos5443 Thanks for responding
Thanks for the video.Mine when I'm cutting closes that blade so I have to raise the fade what keeps the blade on place? Thanks
Same as mine ... How do u got it to fix properly ????
Plzzz help
I was interested however why the background music
Hi! Bro! My magic clip broken the spring.. do u know how do i get the spring..?
Bo I sure don't brotha I haven't came across a website for that part yer
Joseph Alejos alright thank u the answer bro!
do you put the brown piece on the gold thing that sticking up
I have some brand new straight out of the box, cordless magic clips. I took the blades off to replace with a ceramic blade now they won't turn back on. Do you have a remedy?
Try taking off the blade and all the little pieces as well then try to turn them on if it doesn't turn on then it might be a issue with the switch or the battery might be no good but that is a slight possibility since you just took them out the box
I tried deep cleaning my magic clips but no matter what the spring part always pops offf I even check and everything and I don’t understand!???
If you watch my other video I have on that part I go into a better detail
Joseph Alejos yea I saw that one too , seems that the tension spring won’t hold that little part into place anymore you have to hold on to it ...
@@MrXxtoshixx what helps if you place spring one the clipper them place the brown part on the cutting blade line up the Rotary motor to the center of the Brown bees then hold the blade from the sides then place fade blade on top using the top and back remove fingers that's holding the cutting blade place screw on the fade blade then the other then from there it should be good to let go but dont tighten all the way. This give you time to let go off the cutting blade and be able to adjust the fade blade as you please then once you find the sweet spot tighten up the screws then you should be golden
Thanks for the video bro.
wires from my motor detached from the motherboard any tips?
You can solder the wires back but just make sure it to the right spot
The thingy that holds the cutting blade popped out and I managed to put it back on but now my clips are noisy
You can probably use oster clipper grease on the brown part that connects to the the rotor motor
My small top blade is moving how can I fix that
is it moving sideways? cuz mine has been doing that since i bought it.
I lost that plastic piece at 10:40, now the spring is popping out. Anyone know what it’s called, so I can maybe get a replacement :( ??? Please help
telloprofesional.com/gb/accessories-and-replacements/replacement-support-blade-cordless-magic-clip-wahl-12964-4015110018643.html
Heres a link I found hope this helps
Joseph Alejos that’s exactly what I needed!! Thank you so much, your a live saver.
Great video
The piece that you our on top of the spring keeps popping out, will not stay in place, and when I use the level for open to close it will not stay under the bridge.
Steven Bevilacqua send me a video to 2 my IG: @joefade_
Joseph Alejos I did.
Joseph Alejos I have the same problem and I'm scared cause I didn't pay for 1 year warranty and I need it to cut my sons (3) hair
Yani Mendoza I might be able to help do you have Instagram if so send me a picture of your clipper with the prob so I can get an idea of ways going on with it. and I'll try to help you with the best of knowledge IG: joefade_
Joseph Alejos send me video to
What if my lever still does not move
Possibly can be that its over tightened
My spring keeps popping out black piece
What does the spring hold on too before adding the plastic thing ??!
Watch my other video to see what goes were brotha ruclips.net/video/8mw58giLK4w/видео.html
6:30 Whats the magnet for? I lost mine >.
Do you know what’s the name of that Small plastic that holds the blade?
Mine broke and I don’t know where to get it from or what is called.
Thank you so much
Jolie Mendoza check on eBay with Harley Barber Supply they might carry it. I don't know the name but it could be call the blade holder or the moving blade holder I'm not sure
Cam follower.
Very helpful 👏🏽
I do this, once a year!
great video!!
Damn bro this vid helped me out lol i couldnt figure out where that damn bolt went
Thank you, and thanks for watching
The spring keeps popping out the brown plastic thing. How do u get it in perfect or fix it. Please help
Alexis Zarate what you can do for that is put the top moving blade and then the bottom blade on.
Joseph Alejos the spring pops it out b4 I can even put the blades on
Alexis Zarate can you dm a picture of the brown part to my Instagram. if so the IG name is @joefade_ I just want to check if it's broken or cracked in a place that maybe it's not catching when your placing it back on the clipper
Joseph Alejos thanks g I appreciate it
Alexis Zarate no problem I'll keep an eye out on your msg
Why ar my clipper so loud
Use oil
Yo b, good video but when I took my lever apart, it won’t screw back in tightly ??? Any tips please
AzNwacko how you doing brother sorry I just seeing your comment to do that to make sure that the screw is back in position for when you tighten it. You might have to use like a small Flathead to kind of keep the the nut half in place while tightening and once you tighten it should catch and it should tighten up from there
no worries i fixed the issue, i had to re-order the washer, that helps screw the lever in tight, its a silver washer that you slide into the back part of the clipper.
@@AzNwacko lmao did you lose the washer? i struggled with this for a bit cuz i didnt even realize the washer jumped out.
11:46 bro you said it would fly out mine flew out and now when I try to put it back it it wont stay the spring pushes it out and it dosnt stay without me holding on to it
Okay put the spring on, then brown part on cutting blade then line up the rotor to the center of the brown part(holding the side of the cutting blade with your thumb and index finger) place the fade blade on top( holding with thumb on the bottom of blade and index finger on top on the teeth part of the fasde blade) release your thumb and index from cutting blade. Now place one screw on your fade blade then place the other line up your blade then tighten that should fix your problem
@@josephalejos5443 goood looking out bro real shit
@@playboyblxndz8397 thank you for watching if you need anymore help just shoot me a msg I'll answer with the best knowledgeable I can
@@josephalejos5443 yup NP bro I have a YT channel too 💪 we're in the same bro I'll make sure to hyu if I have any questions like I said good looking out💪 and thank you for the great content ma boii stay up 😎💪
@@playboyblxndz8397 🙏🏼✊🏽💯💈
my brown thing also keeps popping up and im pretty sure it isnt broken
Brian Cruz can you DM a picture of it to me on IG. @JOEFADE_
My chrome thumb cover keeps popping out how to fix that
Kevin Jules does the back still have a clip part on it
Joseph Alejos yes it does
Kevin Jules can you send me a picture for the Clipper and the chrome piece to my IG so u can see how it looks
Kevin Jules @joefade_
Joseph Alejos what is ur ig
everyday?
Why does the brown piece wont stay in place!
Watch my other video on that it's on my page. Itll help you in detail
Hey man thanks for putting this video up. Helped alot. One problem I'm having is the brown plastic piece keeps popping out every time I try and screw the lever back on. Any idea why this is happening? Pretty frustrating because I feel like I've tried everything.
Sagar Desai I have another video for that in here if you like to look at that one
Sagar Desai here's the link ruclips.net/video/8mw58giLK4w/видео.html
You the best!!
Thank you for watching🙏🏼
Mines won't charge anymore, how do I fix it?
devonterobinson97 either the port is not working or the battery went out
Joseph Alejos thanks, do you know where I can find another port?
devonterobinson97 huffs beauty supply on Ebay has a wide section they possibly might have it
is brown thing supposed to overlap the slider or is the sloder suppose to overlap it
mine dont want to charge, works with the cord on but doesnt want to charge , you know anything bout that can help me ?, and my bottom blade move side ways
more then likely the battery went out on the Clipper. as far as the blade goes it might just need realignment.
Ricardo Cisneros if you go to eBay you might be able to find a replacement battery for it. in my personal opinion I would just buy a new one
u could just slide out the silver lid
Thank you
Why is my level handle wobbly? 😏
u did slide in the top plate but why didn't u slide out the top plate haha
Yo bro I can’t fix the spring
It keeps popping out
Place it down word with the points facing down in to the clipper
God bless you
my clipper doesnt cut with guards or hair at all can u plz help me
Christopher Diaz cab you send me a picture of them to my IG to see how the blade is and a quick video on the blades moving
@joefade_
Good video would be much better with music off.
Thanks, I thought I fucked my machine up , hahaha
Thanks for watching.
can u send it so i can try and fix it
Keep your thumb on the part after the spring because it does pop out
Mitch 81 another way to do it is if you put the cutting blade on the brown piece and then attach it back to the spring you'll be able to use your thumb and your index finger to hold it down theb place in the fade blade on top and then from there you'll put your screw on and then you'll be able to move your fingers and adjust the fade blade to the needed zero-gap then at that moment the brown piece will no longer pop off since the fade blade will be holding it
@@josephalejos5443 I did that but now my cutting blade keeps moving when I turn it on even though the screws are tight
@@Mustafa-wd7iv can you send a video to my IG @joefade_
Máximo respecto de Panamá has videos en espanol
at 11:28the plastic keeps getting off
Hey brotha I have another video that gets in detail with that brown part here the link.
ruclips.net/video/8mw58giLK4w/видео.html
ok thanks
can u send me a text how to fix it
i cant it looks gery and the brown pice go flying out
Christopher Diaz okay, umm if you put the moving blade on the brown piece to hold in place the put your bottom blade on it then hold it down . Then place one screw to hold the blade then form there set the second and it should be good to go
plz help
The plastic peice that goes on the spring keeps popping out when I put the cutting blade on , how come ?
I'm currently trying right now and the brown thing keeps flying out if not that and the spring fly out when I try to move the lever.. any soloutions
Karsten Hardeman try to hold down the brown part with the top moving blade.
Karsten Hardeman that should work
Karsten Hardeman if not let me know and I'll give you more advice on it
Joseph Alejos koo yeah I held everything down screwed it in the cutting blade just looks a little crooked
Karsten Hardeman just even it out then tighten it up again