Thanks for this vid bro..but what happens if the machine starts for abit and goes off for good? What do you think is the problem is with the carby if the all other parts are working? Appreciate your feed back..cheers
Hi....Great video...I certainly love this video, very detail about how to dismantle and reinstall back the carburettor.Need to ask a few questions 1. Do you change the faulty part?. 2.Do you used a new gasket?. Really appreciate if you could reply my questions.. Thank you
If your carburetor is same (what you see in video) then start the engine run it for few minutes. Normally 1 and half turn is sufficient. You can feel the power when accelarating. If you need bit more power turn the screw a little bit clockwise. I will do a separate video about it. If you found my videos are helpfull then please do like share subcribe. Thank you
@@WanderingSawMan the flap let's in fuel into the rest of the carb via piston vacuum. If you loosen the tension of the flap (the spring) it will preform faster.
I have two problems with my 4stroke brush cutter please help.. 1. Starting problem..i have to pull the rope in balance or it'll get stuck..can't pull freely like it used to. 2. Accelerator is so hard to press..the cable is fine but the problem is in the machine..
Hi, may i know which brand brush cutter you are using ? Remove the starter assembly and check is there any obstacles. I don't know which kind of starter it is so it is difficult to say something about it. Lets come to accelarator issue.. The problem is with carburetor. You need to remove the slide ( upper side where the one end of acc. Cable connects) and rub it with sand paper, clean it and reset. Problem will be solved. Better replace the slide which is available in nearby shops
А який сенс розбирати карбюратор і його не почистити!Всюди окисли полишалися?!:) А який сенс обрізати нігті на правій руці а на лівій лишити!Не в обіду сказано але ціле відео воно мене дуже дратувало і відволікало!:)
@@shankerjakkula6049 2 stroke or 4 stroke ? May be carburetor overflow is there. If so u hv to check carburetor. Check muffler & exhaust port if it is blocked same problem may occur.
@@amazingtechnical3643 machine konsa ? Chainsaw / Weed cutter ? Heat hotha hai kuch karan se.. yadi current sahi se nahi aatha hai to, engine me kuch problems hai to..
So many reasons can be suggested. 1. Fuel filter kharab hai tho load nahi letha hai 2. Carburetor me kachra hai tho load nahi letha hai 3. Carburetor sahi thareeke me adjust nahi hua hai tho laod nahi letha hai 4. Air filter me gandhgi hai tho load nahi letha hai 5. Cylinder / poston / rings par scrathes vagaira lag gaya tho garam hone ke baad load nahi letha hai
Thanks again for this 😉☺️
You are welcome 😀
Thanks for this vid bro..but what happens if the machine starts for abit and goes off for good? What do you think is the problem is with the carby if the all other parts are working? Appreciate your feed back..cheers
Sorry for late reply🙏 it can happen if it runs with improper mixture of air fuel. If do fine tuning problem will be solved
Hi....Great video...I certainly love this video, very detail about how to dismantle and reinstall back the carburettor.Need to ask a few questions
1. Do you change the faulty part?.
2.Do you used a new gasket?.
Really appreciate if you could reply my questions..
Thank you
Thanks a lot man ! No, I didn't replace any parts. I just took that faulty carburetor to demonstrate.
thank you for sharing your vedio,sir. l learned so much...
Waah !! That's great to hear sir, thank you so much
Which company is good for 2 Stroke brush cutter carburater
According to my knowledge i can say 'WALBRO' is one of the best carburetor.
My brush cutter is auto high rise how to make it slow rise, and what problem it is?
May be accelarotor cable is stuck. Adjust it properly
Sir 2 stroke Neptune power sprayer carburetor does not start if it is open but if it is closed it starts and shuts off immediately.
Did you check the fuel filter ? If that is dirty or blocked replace it. You may need to clean the carburetor
@@WanderingSawMan thanks sir
Great
How to do proper tuning of brushcutter carburator
If your carburetor is same (what you see in video) then start the engine run it for few minutes. Normally 1 and half turn is sufficient. You can feel the power when accelarating. If you need bit more power turn the screw a little bit clockwise. I will do a separate video about it. If you found my videos are helpfull then please do like share subcribe. Thank you
Pura accelerat lene par blade gumna suru hota hai. Wo v speed pakadne me time leta h.plz reply jaldi.pura new brush cutter hai. 4-5ghanta chala h
Carburetor tuning problem hai ye. Wo mixture screw hai na usko thoda sa loose kar dijiye teek ho jayega
How can you make a brush cutter fuel efficient?
By setting proper tuning, well maintenance like cleaning or replacing air filter, spark plug, clutch periodically
That tiny spring in the bowl of the carb, if you cut one end of the tightly coiled part, the engine will have a much faster response time.
Owww !! Is it ? How it works ?
@@WanderingSawMan the flap let's in fuel into the rest of the carb via piston vacuum. If you loosen the tension of the flap (the spring) it will preform faster.
Garam hone ke bad starting me
Problem aati hai exelatar full par Start hota hai 4 stroke hai
Engine kholkar dekhna padega.. Piston ring change karna padega
One of the most completely video about, i had to change "membranes" but no one shows how to take apart carburator...
Thanks for the appreciation man
Why does the blade keep spinning while moving to choke
I didn't understand what you mean..
blade starts rotating suddenly after you move choke open position ?
maeron ba kayong repair kit,para sa mga gasket
Sorry brother, i cant understand
I have problem in my balwan spray pump after speed full engine pick down and off
Carburetor might be blocked.
Its run at half speed but suddendly pick droup after full speed
Tappit ka clearance kitna hona chaiya
Same problem mere spray pump karna ji..
@@mantutakkalaki17 ji aap apne apra pump ka spark plug clean kro then carborator se tuning set kro
I have two problems with my 4stroke brush cutter please help..
1. Starting problem..i have to pull the rope in balance or it'll get stuck..can't pull freely like it used to.
2. Accelerator is so hard to press..the cable is fine but the problem is in the machine..
Hi, may i know which brand brush cutter you are using ?
Remove the starter assembly and check is there any obstacles. I don't know which kind of starter it is so it is difficult to say something about it.
Lets come to accelarator issue..
The problem is with carburetor. You need to remove the slide ( upper side where the one end of acc. Cable connects) and rub it with sand paper, clean it and reset. Problem will be solved.
Better replace the slide which is available in nearby shops
@@WanderingSawMan Neptune brand
@@Deidarasan1000 I think problem is with starter. You may need to disassemble the starter and check where the fault is..
Carburetor air filter side thoda sa petrol spray ho raha he kya problems
May be silencer port is blocked or carburetor overflows
@@WanderingSawMan eske upar ek video banao
@@p.p.4192 Yeah definitely
Walbro carburettor idling problem
Carburetor overflow how to over come it.
1. Check if there is any debris deposit around metering valve
2. You may need to adjust the metering lever
3. Change diaphram & gaskets
Thanks 👌
Oil pump rubber kah milega?
Konsa rubber ??
You can buy spares online or nearby shops
@@WanderingSawMan carburetor m Jo oil pump pump krta h wo rubber
Carburetor tuning hindi video plz uploaded
Wait for some time. Definitely i will do
Okay good
2stok lnjan. full inprametion
Nice.....
Thank you !!
Thumbs 👍
U haven't changed the broken prel
U haven't changed broken premmar bulb with new 1
It was demo sir. That is a scrap carburetor
Brush cutter stops after accelerating
It means sufficient fuel is not entering into cylinder. Check fuel filter / tune carburetor
U turn it 3 times anticlockwise
3 ×180 degrees
എങ്ങനെ ഇതു കറക്റ്റ് ആയി ട്യൂൺ ചെയ്യാം
Tune cheyyunathin munb 1.5 turn il vekkanam. Pinne engine kurach heat aayithin shesham accelarator koduthu nokanam tuning veno vende enn. Veli pora ennundengil melle tight cheyyanam. Athraye ullu
Hamari. Masheen petrol no uttha rahi. What should we do
Please tell us about this
Matlab combustion chamber tak petrol nahi aaraha hai ?
Petrol tank ke andar filter rehta hai usko clean karke dekhiye ek baar. Isse problem solve nahi hoga to carburetor ko clean karna padega
Ishq carbeta ka kimat kitna hai
Price : 1400 /-
А який сенс розбирати карбюратор і його не почистити!Всюди окисли полишалися?!:)
А який сенс обрізати нігті на правій руці а на лівій лишити!Не в обіду сказано але ціле відео воно мене дуже дратувало і відволікало!:)
it would be great if translated into english
😊
His carbeter will be found and its price
What sir ? I didn't understand 🙏
Carburetor bol Kaha milega
Matlab carburetor ka float hai kya ?
ഈ മോഡൽ കാർബാറേറ്റർ വേണം ഫോൺ നമ്പർ തരുമോ
9745105148
Corburetar oil leakege problem am cheyali
Replace gaskets.. Check screws are properly tighten or not
@@WanderingSawMan sir corpuretor lo spang filter in petrol leakege problem
@@shankerjakkula6049 2 stroke or 4 stroke ? May be carburetor overflow is there. If so u hv to check carburetor.
Check muffler & exhaust port if it is blocked same problem may occur.
@@WanderingSawMan 2 stroke sir
@@shankerjakkula6049 then do as i instructed.
Kya is ma mistake kaha thi
Mistake kya hai ?
@@WanderingSawMan bhai heat bhi ho raha h kya problem hogi
@@amazingtechnical3643 machine konsa ? Chainsaw / Weed cutter ?
Heat hotha hai kuch karan se.. yadi current sahi se nahi aatha hai to, engine me kuch problems hai to..
@@WanderingSawMan spray pump h
@@WanderingSawMan speed full karne par band ho jata h or heat bhi hoata ha
Hi
@@pranjitboro9709 👋
Hindi mein
Detail me ek aur video banaunga. Thoda time deejiye..
Hindi me Plz guru ji
Lod nahi le raha h
So many reasons can be suggested.
1. Fuel filter kharab hai tho load nahi letha hai
2. Carburetor me kachra hai tho load nahi letha hai
3. Carburetor sahi thareeke me adjust nahi hua hai tho laod nahi letha hai
4. Air filter me gandhgi hai tho load nahi letha hai
5. Cylinder / poston / rings par scrathes vagaira lag gaya tho garam hone ke baad load nahi letha hai
Yes yes yes