• Defective exposure lamp • Defective exposure lamp stabilizer • Defective exposure lamp connector • Unclean scanner mirror • Scanner mirror out of position • Defective SBU board • Defective SBU connector • Lens block out of position • Incorrect position or width of white plate scanning (* SP4-015)
This is a lamp problem. Check if the lamp is lit. If it is lit during copying, you may have a dirty copy machine. Maintain it and wash the glass, mirrors and lamp in particular. If this does not help, then there is another problem: 1 Check the connector between scanner unit-MFPB CN102, CN103 for proper connection and correct as necessary. - - 2 Check for possible extraneous light and correct as necessary. - - 3 Clean the lens, mirrors, CCD surface, and shading sheet if dirty. - - 4 Correct reflective mirror of the scanner if faulty, or change scanner mirror. - - 5 Replace scanner unit - - 6 MFPB F102, F105 conduction check - - 7 Replace MFPB
was using a Ricoh Aficio MP C4000 for photocopying but after I changed the black toner, I am getting only blank pages. Can anybody help me with it. Thank you
• Exposure lamp defective • Lamp regulator defective • Lamp regulator harness damaged, disconnected • Dirty standard white plate • Scanner mirror dirty or out of position • Lens dirty, out of position • SBU board defective
Code: 101 Description: Exposure Lamp Error The scanner has scanned the white plate, but cannot detect the white level. Causes: • Defective exposure lamp • Defective exposure lamp stabilizer • Defective exposure lamp connector • Unclean scanner mirror • Scanner mirror out of position • Defective SBU board • Defective SBU connector • Lens block out of position • Incorrect position or width of white plate scanning (* SP4-015)
Code: 144 Description: Communication Error between BICU and SBU The BICU cannot correctly establish communication with the SBU. Causes: • Loose connection of the flat cable between the BICU and the SBU • Defective flat cable between the BICU and the SBU • Defective BICU • Defective SBU
Hi, SC552 is a very popular fault that most often occurs after self-repairing a Fuser Unit, or after a Fuser Unit failure. Theoretically, you may have a damaged or dirty thermopile sensor located behind Fuser. But often the cause of sc552 can be simply damaged FUSER FIXING FILM. If you have previously unfolded FUSER, it is very likely that you folded it incorrectly - incorrectly installed heater cover for FUSER FILM. Soon I will make a film about this FUSER I'm curious, what will you write next? Best wishes Tomasz Jemiołek
All you guys here posting how to fix this and that need to look this info up in the Service Manual.
@private3219 If you have a Service Manual you can check it, but do people have it?
Obrigado pelo vídeo, ajudou muito! congratulations!
Estou muito quieto que eu possa ajudar. Saudações da Polônia.
Hola en mi impresora ricoh mp c2003 tengo el error sc 144-00, me puedes orientar como arreglarlo, por favor?
look this: www.copytechnet.com/forums/ricoh-savin-gestetner-lanier/148329-mpc2003-sc144.html
thanks, What about error SC: 829 >> Code: 301 ??
If you have sc829 then:
1. Replace the RAM DIMM.
2. Replace the controller board.
Hi sir l had SC 101 problem in richo MP 2000 & I don't know how to solve it please help me
Thanx
• Defective exposure lamp
• Defective exposure lamp stabilizer
• Defective exposure lamp connector
• Unclean scanner mirror
• Scanner mirror out of position
• Defective SBU board
• Defective SBU connector
• Lens block out of position
• Incorrect position or width of white plate scanning (* SP4-015)
Tomasz Jemiołek
Thank you so much
Saludos estimado amigo , por solicitarle tu ayuda tengo un error SC101-01 En una RICOH Aficio MP5001
When was the last time you did the maintenance of your photocopier?
Man, I haven't had to do a scanner lamp or cable in like 10 years. Not looking forward to it 😐
These problems keep coming back.
I have a Konica copier that comes error code 9401 how can i solve it, please
This is a lamp problem. Check if the lamp is lit. If it is lit during copying, you may have a dirty copy machine. Maintain it and wash the glass, mirrors and lamp in particular. If this does not help, then there is another problem:
1 Check the connector between scanner unit-MFPB CN102, CN103 for proper connection and correct as necessary. - -
2 Check for possible extraneous light and correct as necessary. - -
3 Clean the lens, mirrors, CCD surface, and shading sheet if dirty. - -
4 Correct reflective mirror of the scanner if faulty, or change scanner mirror. - -
5 Replace scanner unit - -
6 MFPB F102, F105 conduction check - -
7 Replace MFPB
GOOD
Thanks
how to rest sc120 ricoh error?
I had such a problem in 2020 and the errors were from this PCB which powers the scanner on the scanner under the lamp
this lamp got sell?
Lamp Ricoh MPC3002 copy-expert.com/pl/p/Lampa-skanera-RICOH-MPC3002-MPC3502-MPC4502-MPC5502-MP4002-MP4002SP-MP5002-MP5002SP-D1295331-D1291722/2798
was using a Ricoh Aficio MP C4000 for photocopying but after I changed the black toner, I am getting only blank pages. Can anybody help me with it. Thank you
This is a very strange symptom. There is no color? It may loosen the Drum Unit and will not contact. But in that case other colors should be visible,
Hi,
Only blank pages are coming out.
No colour at all.
Any other way to resolve this issue.
Thank you
I would replace the charging roller
Ricoh Mp 2852 error sc144-01 help me please
If you encountered this problem, please write back user ovis.
I have error sc 154-00 ricoh mp402 ... anybody can help me with it, please.
• Exposure lamp defective
• Lamp regulator defective
• Lamp regulator harness damaged, disconnected
• Dirty standard white plate
• Scanner mirror dirty or out of position
• Lens dirty, out of position
• SBU board defective
Ricoh MP 1600 SC error 101 and 144 solve plz
Code: 101
Description: Exposure Lamp Error
The scanner has scanned the white plate, but cannot detect the white level.
Causes: • Defective exposure lamp
• Defective exposure lamp stabilizer
• Defective exposure lamp connector
• Unclean scanner mirror
• Scanner mirror out of position
• Defective SBU board
• Defective SBU connector
• Lens block out of position
• Incorrect position or width of white plate scanning (* SP4-015)
Code: 144
Description: Communication Error between BICU and SBU
The BICU cannot correctly establish communication with the SBU.
Causes: • Loose connection of the flat cable between the BICU and the SBU
• Defective flat cable between the BICU and the SBU
• Defective BICU
• Defective SBU
Non e' una mp 2000
Ricoh .grazie
Come mai? Scrivi com'è la macchina secondo te?
Ricoh mp c2011 error 552
Hi,
SC552 is a very popular fault that most often occurs after self-repairing a Fuser Unit, or after a Fuser Unit failure. Theoretically, you may have a damaged or dirty thermopile sensor located behind Fuser. But often the cause of sc552 can be simply damaged FUSER FIXING FILM. If you have previously unfolded FUSER, it is very likely that you folded it incorrectly - incorrectly installed heater cover for FUSER FILM. Soon I will make a film about this FUSER
I'm curious, what will you write next?
Best wishes
Tomasz Jemiołek
Ricoh mp2551 error sc144 ????