Guys I have figured it out. If your PC is continuously restarting and giving different error codes every time not giving you even 5seconds on welcome screen then your RAM is at fault. Simply swipe your current RAM with a new one. I had 2+2GB DDR3 RAM and I swapped both of them with one 8GB stick. As an added measure I cleaned all fans & heat-sinks (including Graphic card’s heat sink & SMPS) and applied thermal paste again. Problem solved. My old RAM was 10yrs old.
@@olalderh I had the same issue and I already rest to the standard “auto” some times it’s popping the blue screen not Often what’s the resolution for this and I used water cooling for my cpu i9 and 16GB rams and 3080 GPU with 750 psu ! Was that that the psu coursing this ?
@@ShortsRecapsofficial Same problem today... Mine was a bad monitor. Swapped it....Bam.. no more problem. More accurately: I think the monitor required a driver that wasn't compatible with my system... Had this problem previously, and yes it was the ram... Another time, same thing, only it was a bad PSU. That's the problem with windows error codes.. they basically mean dick.
Just crashed 2 days ago. I suspected system instability, I have cpu that support only 2933 mhz ram and I bought 3200 mhz ram. This RAM thing need to be fixed. Good advice, check you system or rather CPU or that called "Intel" or "AMD" requirements. I will get my RAM in 14 days, I will update after I put Correct speed RAMs.
@@yoshimitsu8643 RAM is fixed but blue screen is likely from hardware issues. Since I get my 8TB Samsung EVO as storage the problem occured, 3 bits per cell is likely cause this. My main storage is SSD M.3 with 2 bits per cell. Too bad this lovely 8TH SSD is cost like $500-$600.
I think i found my problem by running the device diagnostic, it came back and said that windows update had the auto driver update turned off (so i assume i had out of date drivers because i never updated them), i then clicked the button to allow windows to update the drivers, hopefully problem fixed, thanks mr uploader.
I love how these system repair videos always instruct people to run programs in Windows on a system that won't launch into Windows because it stops on the BSOD. How exactly do you run a Windows program when Windows won't boot?
Hi there, thank you for your question! There are a few options available you can try booting into Safe Mode, using a Windows Recovery Disk or Installation Media, creating a bootable USB drive with diagnostic and repair tools, or removing the hard drive and connecting it to another computer.
@@RecoveritDataRecoverySoftware If you take a disc that doesn't boot and put it into another computer, it still isn't going to boot if the issue is with Windows. Also, a modern Windows install will typically not boot on a different motherboard than it was installed on originally. Booting into Safe Mode would be great but this is usually not an option either when getting BSOD because post never allows the opportunity.
There is simple solution for this 1: clean motherboard 2: Replace with new RAM (latecy should match for dual or four stick 3: Fresh install Windows system Done✓
I can't run chkdsk because it says " the volume is in use by another process" ! I have also tried all the other methods and I still get BOD IRQL thing With failed storport sys ! But not as much as I did! Help! Cheers
I've been facing the same error. Apparently the AMD GPU driver (amdkmpfd.sys) is causing the error. To fix the issue I had to uninstall the driver using DDU and install the one available in the laptop official support site. Is there a way to update the driver and not run into BSOD? Thanks.
@VictisGaming684 Once you encounter a blue screen error you'll be given a message as to what is causing the error. amdkmpfd.sys was the error I received.
I asked a question in Quora and someone said that it happens when there are too many ports connected. To be clear I only connected the mouse and keyboard, as well as a VGA monitor through HDMI, is this also the reason why I get the same screen thrown at me?
Hi there, thank you for your question! Although having too many ports connected could potentially contribute to the error, it's not necessarily the only cause. To try and resolve the issue, you can run hardware diagnostic tests, update your drivers, remove recently installed software or hardware, check for malware, and make sure all of your hardware components are compatible.
im kidna woried recently today this bsod happened, and i don't think its hardware its something has to do with drivers... cause i was kinda stupid and was installing and uninstalling AMD Custom made drivers that crashed my PC and kept restarting then did DDU and installed official, i think i messed something up with my windows or drivers or amd drivers what should i do? i tried sfc /scannow it didn't find anything
I used the first part of this, to try and fix my pc randomly turning off (no bsod) and after using the first thing it cause this code bsod to appear. I've since used the recovery to get back to a stable date. I still have the random turn offs. And when I say random I mean random. Seems like it will work for months, or sometimes randomly shut off 2 times in one day.
Hi there, thank you for your question! If you've already tried using the recovery option and you're still experiencing random shutdowns on your PC, there may be other underlying issues causing the problem. It's important to check for potential hardware problems, such as overheating or failing components, and to update your drivers and run antivirus scans to rule out any software issues. If you've exhausted all troubleshooting options, it may be necessary to seek professional assistance to diagnose and fix the problem.
Hi there, thank you for your question. If your PC is experiencing issues, such as crashing or freezing, while playing Roblox or watching RUclips, there are several potential causes. Here are some general troubleshooting steps you can take: Check System Requirements: Ensure that your PC meets the minimum system requirements for both Roblox and RUclips. If your hardware is below the requirements, it could lead to performance issues. Update Graphics Drivers: Make sure your graphics drivers are up to date. Outdated or incompatible drivers can cause performance problems. Visit the website of your graphics card manufacturer (NVIDIA, AMD, or Intel) to download and install the latest drivers. Monitor System Temperature: Overheating can lead to performance issues and crashes. Use monitoring software to check your CPU and GPU temperatures while playing games or watching videos. If temperatures are too high, consider improving your PC's cooling, such as adding more fans or cleaning out dust from the system.
The problem is my Win10 PC is on a restart spree. I can not get even 5 seconds on the desktop screen to do all this. PC is restarting instantly after the welcome screen appears and is giving different error codes every time. What to do? Please help!
@@ThePerfectG Guys I have figured it out. If your PC is continuously restarting and giving different error codes every time then your RAM is at fault. Simply swipe your current RAM with a new one. I had 2+2GB DDR3 RAM and I swapped both of them with one 8GB stick. As an added measure I cleaned all fans & heat-sinks (including Graphic card’s heat sink & SMPS) and applied thermal paste again. Problem solved. My old RAM was 10yrs old.
@@thesherrifsheriff4251 Guys I have figured it out. If your PC is continuously restarting and giving different error codes every time then your RAM is at fault. Simply swipe your current RAM with a new one. I had 2+2GB DDR3 RAM and I swapped both of them with one 8GB stick. As an added measure I cleaned all fans & heat-sinks (including Graphic card’s heat sink & SMPS) and applied thermal paste again. Problem solved. My old RAM was 10yrs old.
When I do the memory diagnostic, my CPU fan starts going really fast and then the computer shuts down. Same thing that happens when windows is running so I think it’s probably time for a new CPU.
Hi there, thank you for your question! It sounds like it is most likely a CPU cooling issue you could try applying new thermal paste to your CPU and that should help with cooling I would also recommend looking at the LED's on your motherboard when launching to see if the issue occurs on CPU start up as well to confirm your suspicion.
Hi there, thank you for your question! I would recommend trying to run your computer from a Bootable USB drive and then try repairing the issue while using the USB.
You start with press the cortana search box...but my pc cant get passed (your device run inti a problem) so i cant press anything....now what do i do ?
Hi there, thank you for your question. If your PC is stuck on a "your device ran into a problem" error screen and you can't access the Cortana search box or any other functionality, you'll need to perform some troubleshooting steps to try and resolve the issue. Here's what you can do: Restart Your Computer: The first step is to perform a forced restart of your computer. Press and hold the power button until your computer turns off. Wait a few seconds, and then turn it back on. This may help clear the error. Safe Mode: If your PC continues to encounter the error and won't boot normally, try booting into Safe Mode. To do this, turn off your PC and then turn it on again. As soon as it starts to boot, repeatedly press the F8 key or another function key (depending on your PC's manufacturer) to access the Advanced Boot Options menu. From there, select "Safe Mode." Once in Safe Mode, you can attempt to diagnose and resolve the issue. System Restore: If you have previously created a System Restore point on your computer, you can try to restore your system to a point when it was working correctly. To access System Restore, you can try the following steps: Boot into the Advanced Boot Options menu as mentioned in step 2. Select "Repair your computer" and follow the on-screen prompts to access System Restore.
Could it be hardware issue like bad connectors, thermal paste etc? And how does one clean un/install drivers? Cause my PC gives me this error when I boot up minecraft or deep rock galactic.
Hi there, thank you for your question! Yes, it definitely could be caused by any of those issues you listed, I would recommend trying a cpu/gpu temperature monitor to see if you get high temps when playing, Also try checking your task manager to see how the usage is for each components.
Corrupt drivers - windows update was clean, system security is up to date and fine, ran a sfc/scannow came back ok, gpu drivers are up to date. System files damaged? how?, i was just watching a youtube video thats all and anyhow i already ran a scan system program which came back negative for corrupt files. Incompatible drivers? i havent installed anything. CPU overheating...hmmm, it's possible but dountful seeing as i have 120mmAIO with fans in a cool room with a low overclock, but it's possible. Faulty hardware componant issues, also possible because my gpu has been playing up lately. Third party application, dountful. Ok, so it's either my CPU which i can remedy by turning off my O/C and see how the system runs or it's my gpu :(
Hi there, thank you for your question! Sometimes even a simple overclock can cause the issue id recommend removing the overclock and see if the issue stops.
You indicated that the IRQL stop code is often associated with a driver problem. Accordingly, which of the various approaches would help identify the driver and repair it?
Hi there, thank you for your question. You can try: 1. Check the error message: The IRQL stop code error message often includes the name of the driver causing the issue. Make a note of the driver's name and search for its updates or fixes. 2. Use Windows Event Viewer: Open the Event Viewer to check for any error logs related to the driver in question. This can provide more information about the issue and help you identify the problematic driver.
The corrupt registry files one found a few and corrected them... then it did it again. I am absolutely stumped and have done everything from this video. Hardware is fine. No clue, any help?
Hi there, thank you for your question! You may need to use a recovery drive or installation media to repair your system files rebuild the boot configuration data, or perform a startup repair, as not even being able to access the computer could indicate further issues so I would recommend taking it to a professional for further assistance.
my cpu was just overheating, maybe just consider to clean your pc, lower the clock speed or CAUTION: adjust the cpu temperature emergency power off threshold (the last one could damage your cpu, if done wrong)
Hi there, thank you for your question! If you laptop isn't even turning on I would recommend trying to use a bootable USB drive and see if that works otherwise I would recommend taking it to a professional as it might be an internal issue.
(i sometimes comment first before watching the video). This just happened to me, just watching a youtube video and then out of the blue blam! this came up? wtf....anyway, lets watch the vid..
@@RecoveritDataRecoverySoftware thanks for answering my question. Because i accidentally removed the cmos battery then this problem happened and I have tried restart several times but this problem and other blue screen problem happened . Thanks 👍
how can i be able to enter the windows to run system restore while im having boot issues that doesnt even lets me to get access to my pc. i tried formating but my pc doesnt boot on the usb, i did the boot order as usb setting on the top and also it says on bottom of the driver irql not less or equal, what failed: ACPlsys. can anyone help me?
Hi there, thank you for your question! The error message you received indicates that there is a problem with the driver ACPlsys. This error can be caused by a variety of issues, including corrupted system files, faulty memory, or a corrupted hard drive. You can use the Windows Recovery Environment (WinRE) to resolve boot issues with Windows 10. To access WinRE, you can interrupt the boot sequence by pressing the power button as soon as the Windows logo appears. Repeat this process two more times, and on the third interruption, Windows 10 will open into the recovery environment. From there, you can use the “Startup Repair” tool to fix booting issues with Windows 10.
My Pc is newly upgrade, and the stop code error " IRQL NOT LESS OR EQUAL " always pop up randomly. Like 5 days gap. What seems to be the problem in my PC? (The sfc scan found a corrupt files and fixed it) it should be ok then?
Hi there, thank you for your question! It may not necessarily resolve the issue if the root cause is elsewhere. Check for Driver Issues by ensuring all drivers are up to date, run a Memory Test to check for RAM problems, keep Windows updated, and inspect hardware for loose or faulty components. Revert overclocked settings hope these steps help.
Hi there, thank you for your question! If Windows is not loading during a no display error, you can try checking your hardware connections, connecting a different monitor, booting into Safe Mode, using System Restore, using a recovery drive. Accessing these options may require accessing the BIOS or UEFI firmware rather than from within Windows itself.
I just tried install a new operating system and it keeps giving me this error on the loading process. With your options I have tried most of them which I can and it still posting the same error ⚠️. Is there anything I can do again apart from what is in this video
How about windows 8.1? but can i still do this like what you said about those im usually having this error on my windows 8.1 but i hoped this will work
Hi there, thank you for your question! To fix this error, you can start by updating your drivers, especially your network drivers. You can also run a hardware diagnostic test to check for any issues with your hardware components. If the error persists, you can try running a system file checker scan or performing a clean install of Windows. It's important to note that the downgrade may not have solved the issue since it could be related to hardware or software problems.
Hi there, thank you for your question! If you're unable to get past the blue screen of death, you can try starting your computer in Safe Mode. To do this, restart your computer and press the F8 key repeatedly until the Advanced Boot Options menu appears. From there, select "Safe Mode" and try the steps in shown in the video again.
Hi there, thank you for your question! You can search for a tool called windows memory diagnostics in the search bar and choose the restart and check for problems. I would also recommend making sure all your components are correctly connected such as RAM and making sure nothing is loose. If none of those work trying rolling back your pc to a previous version hopefully that helps.
Hi there, thank you for your question. try restarting your computer as it may resolve the issue. Secondly, make sure your Windows operating system is up to date by checking for updates and installing them if available. Thirdly, check your hardware for any faults by ensuring all components are securely connected and running a diagnostic test. Fourthly, run a virus scan as malware or viruses can cause the error. Finally, if your disk is locked, follow the instructions provided by your disk encryption software to unlock it. If these steps do not fix the issue, consider seeking the help of a professional technician or contacting your computer manufacturer for further assistance.
Help! My laptop got really wet on the rain 2 days ago and it's working but the screen is back what should I do?? I don't want my mom to know it please!! If you know make a video
I can't run the disk check command because it says 'the volume is in use by another process', how am I supposed to check it? Edit: I also ran the memory test, and it said there were no memory errors found, but I've gotten 'memory management' error codes before along with the irql code. This doesn't make sense to me. Edit 2: I also ran the hardware diagnostic test and found no errors, yet I'm stilling getting the error code when I'm trying to download games. Someone please help me I have no idea what's wrong, I can't download anything...
i have bought an IBM System X server and i get this error when loading the Bootable USB with Server 2022. if the discs are not setup in raid i dont get the BS, but then ofc i cant see the discs.. as soon as i set my discs up in raid 5 i can no longer reach the installation before BS "storport.sys DRIVER IRQL NOT LESS PR EQUAL" please, do you have any advice?
Hi there, thank you for your question! Try to update the bIOS and chipset drivers this might resolve your issue.Check if the BSOD errors are caused by "stornvme.sys" and update the driver if necessary. Lastly try Downgrade the HPCISSS2 driver to version 62.24.2.64
@@RecoveritDataRecoverySoftware thank you for the reply, i fixed the issue though, i had to, as you just said, update the bios to the 2018 release, and i had to inject the raid controller drivers during the installation. i had no luck with server 2022. so im running 2012 R2. thank you again
Nothing helped , any other advice , like what hammer to use to back the side in, or which petroleum burns the best ?
Or just use a rocket launcher...
Yep…
I think u should use hydrogen it is the most efficient
But don't burn down your house down
5.56x45mm works the best
Guys I have figured it out. If your PC is continuously restarting and giving different error codes every time not giving you even 5seconds on welcome screen then your RAM is at fault. Simply swipe your current RAM with a new one. I had 2+2GB DDR3 RAM and I swapped both of them with one 8GB stick. As an added measure I cleaned all fans & heat-sinks (including Graphic card’s heat sink & SMPS) and applied thermal paste again. Problem solved. My old RAM was 10yrs old.
Yeah my ram is new and it’s still doing it
@@atherues1337 same dude
If the RAM is overclocked (for example, you have the XMP active in BIOS), it is probably that. Not necessarily the RAM is faulty.
@@olalderh I had the same issue and I already rest to the standard “auto” some times it’s popping the blue screen not Often what’s the resolution for this and I used water cooling for my cpu i9 and 16GB rams and 3080 GPU with 750 psu ! Was that that the psu coursing this ?
@@ShortsRecapsofficial Same problem today... Mine was a bad monitor. Swapped it....Bam.. no more problem. More accurately: I think the monitor required a driver that wasn't compatible with my system... Had this problem previously, and yes it was the ram... Another time, same thing, only it was a bad PSU. That's the problem with windows error codes.. they basically mean dick.
This help a lot. My laptop suddenly getting blue screen in every 30 minutes, *"Repair You Registry To Corrupted Files"* Works.
THIS REALLY HELP 5 days without blue screen.
Just crashed 2 days ago. I suspected system instability, I have cpu that support only 2933 mhz ram and I bought 3200 mhz ram. This RAM thing need to be fixed. Good advice, check you system or rather CPU or that called "Intel" or "AMD" requirements. I will get my RAM in 14 days, I will update after I put Correct speed RAMs.
@@someguyfromarcticfreezer6854so it is a ram problem? Why didn’t it show when you scanned for memory diagnostic
@@yoshimitsu8643 RAM is fixed but blue screen is likely from hardware issues. Since I get my 8TB Samsung EVO as storage the problem occured, 3 bits per cell is likely cause this. My main storage is SSD M.3 with 2 bits per cell. Too bad this lovely 8TH SSD is cost like $500-$600.
I think i found my problem by running the device diagnostic, it came back and said that windows update had the auto driver update turned off (so i assume i had out of date drivers because i never updated them), i then clicked the button to allow windows to update the drivers, hopefully problem fixed, thanks mr uploader.
did this fix your issue? mine came back and said the same thing. hoping this’ll fix it!
Mines always says this error then reboot
@@alltoounwell3411did this work for you ?
I love how these system repair videos always instruct people to run programs in Windows on a system that won't launch into Windows because it stops on the BSOD. How exactly do you run a Windows program when Windows won't boot?
Hi there, thank you for your question! There are a few options available you can try booting into Safe Mode, using a Windows Recovery Disk or Installation Media, creating a bootable USB drive with diagnostic and repair tools, or removing the hard drive and connecting it to another computer.
@@RecoveritDataRecoverySoftware If you take a disc that doesn't boot and put it into another computer, it still isn't going to boot if the issue is with Windows. Also, a modern Windows install will typically not boot on a different motherboard than it was installed on originally.
Booting into Safe Mode would be great but this is usually not an option either when getting BSOD because post never allows the opportunity.
Also, didn't you play Charlie on the series "Lost"? :)
How could I search if I'm not getting to windows at all. 3:10
This is mostly DIAG and very little "fix" - in another video they said to turn off pre-caching on the drives in device man - that fixed it for me
What video if you remember?
There is simple solution for this
1: clean motherboard
2: Replace with new RAM (latecy should match for dual or four stick
3: Fresh install Windows system
Done✓
I can't run chkdsk because it says " the volume is in use by another process" ! I have also tried all the other methods and I still get BOD IRQL thing With failed storport sys ! But not as much as I did! Help! Cheers
I too have the same issue. “volume is in use by another process”
I've been facing the same error. Apparently the AMD GPU driver (amdkmpfd.sys) is causing the error. To fix the issue I had to uninstall the driver using DDU and install the one available in the laptop official support site. Is there a way to update the driver and not run into BSOD? Thanks.
Plug in an external monitor. It will load a primitive driver, and shouldn't crash.
@VictisGaming684 Once you encounter a blue screen error you'll be given a message as to what is causing the error. amdkmpfd.sys was the error I received.
Thank you for helping us, from the Philippines 🎉
Glad to hear that! Please subscribe our channel.
Thanks! Solution 1 worked for me. One of my RAM sticks has a problem, removed it, and problem solved.
I asked a question in Quora and someone said that it happens when there are too many ports connected. To be clear I only connected the mouse and keyboard, as well as a VGA monitor through HDMI, is this also the reason why I get the same screen thrown at me?
Hi there, thank you for your question! Although having too many ports connected could potentially contribute to the error, it's not necessarily the only cause. To try and resolve the issue, you can run hardware diagnostic tests, update your drivers, remove recently installed software or hardware, check for malware, and make sure all of your hardware components are compatible.
The problem is when I try to diagnose it says an unknown error occurred any solution
Can this happen because of a new GPU? I recently installed a RTX 3080 and now it has been happening all the time on RDR2 but not on other games.
Probably a driver issue then
@@kushio214 Put my 3080 into a new PC build I’ve done and no problems since so idk but it works
@@sack8439 That's cool
Happens to me on the division 2 but no other games
I’m having same problem any fix?
excellent video, concise and very useful. thanks!
im kidna woried recently today this bsod happened, and i don't think its hardware its something has to do with drivers...
cause i was kinda stupid and was installing and uninstalling AMD Custom made drivers that crashed my PC and kept restarting then did DDU and installed official, i think i messed something up with my windows or drivers or amd drivers
what should i do?
i tried sfc /scannow it didn't find anything
i've had this error and also apc_index_mismatch
What if non of this solved blue screen crash ?
Can't even get to windows, or even to get it to boot from a USB without it going to the BSoD
I used the first part of this, to try and fix my pc randomly turning off (no bsod) and after using the first thing it cause this code bsod to appear. I've since used the recovery to get back to a stable date. I still have the random turn offs. And when I say random I mean random. Seems like it will work for months, or sometimes randomly shut off 2 times in one day.
Hi there, thank you for your question! If you've already tried using the recovery option and you're still experiencing random shutdowns on your PC, there may be other underlying issues causing the problem. It's important to check for potential hardware problems, such as overheating or failing components, and to update your drivers and run antivirus scans to rule out any software issues. If you've exhausted all troubleshooting options, it may be necessary to seek professional assistance to diagnose and fix the problem.
The solution it 's good for windows 11 ?
Hi there, thank you for your question! Yes it should work on windows 11.
@@RecoveritDataRecoverySoftware ok
My pc cause this while playing roblox and some time it cause while watching youtube please help me i am done with it plzzz😢😢😢
Hi there, thank you for your question. If your PC is experiencing issues, such as crashing or freezing, while playing Roblox or watching RUclips, there are several potential causes. Here are some general troubleshooting steps you can take:
Check System Requirements:
Ensure that your PC meets the minimum system requirements for both Roblox and RUclips. If your hardware is below the requirements, it could lead to performance issues.
Update Graphics Drivers:
Make sure your graphics drivers are up to date. Outdated or incompatible drivers can cause performance problems. Visit the website of your graphics card manufacturer (NVIDIA, AMD, or Intel) to download and install the latest drivers.
Monitor System Temperature:
Overheating can lead to performance issues and crashes. Use monitoring software to check your CPU and GPU temperatures while playing games or watching videos. If temperatures are too high, consider improving your PC's cooling, such as adding more fans or cleaning out dust from the system.
Guys i need help when i start a game on roblox after 5/10 seconds it crashes my pc and does the blue screen and wich the error of the video
You found fix this?
@@William_zamazor idk, i don't remember...
The problem is my Win10 PC is on a restart spree. I can not get even 5 seconds on the desktop screen to do all this. PC is restarting instantly after the welcome screen appears and is giving different error codes every time. What to do? Please help!
Did you find a solution?
Did you figure it out?
@@ThePerfectG Guys I have figured it out. If your PC is continuously restarting and giving different error codes every time then your RAM is at fault. Simply swipe your current RAM with a new one. I had 2+2GB DDR3 RAM and I swapped both of them with one 8GB stick. As an added measure I cleaned all fans & heat-sinks (including Graphic card’s heat sink & SMPS) and applied thermal paste again. Problem solved. My old RAM was 10yrs old.
@@thesherrifsheriff4251 Guys I have figured it out. If your PC is continuously restarting and giving different error codes every time then your RAM is at fault. Simply swipe your current RAM with a new one. I had 2+2GB DDR3 RAM and I swapped both of them with one 8GB stick. As an added measure I cleaned all fans & heat-sinks (including Graphic card’s heat sink & SMPS) and applied thermal paste again. Problem solved. My old RAM was 10yrs old.
How do we do all this if we have the blue screen rt now???, Like how can I do all these without opening my laptop????
Long press the power button nd switch it off nd on again..
When I do the memory diagnostic, my CPU fan starts going really fast and then the computer shuts down. Same thing that happens when windows is running so I think it’s probably time for a new CPU.
Hi there, thank you for your question! It sounds like it is most likely a CPU cooling issue you could try applying new thermal paste to your CPU and that should help with cooling I would also recommend looking at the LED's on your motherboard when launching to see if the issue occurs on CPU start up as well to confirm your suspicion.
what if it keeps restarting and not letting me in i downloaded wrong wifi drivers and it wont even let me in
Hi there, thank you for your question! I would recommend trying to run your computer from a Bootable USB drive and then try repairing the issue while using the USB.
I get an error code when i do the hardware diagnostic. Error code: 0x8000FFFF why is this the case?
May I ask how you get to solve this?
Great video thank you for your help😊
Updating the BIOS sorted me out :)
i tried all of these ugh still happens must be something else
Did you figured it out ?
Cause I am having the same problem
@@anubhavsharma7981 get new drivers
didnt work for me, im just trying to play valorant with my friends :(
Same problem like me :(
broooo same i think its because of VANGUARD riot anti cheat alott of people are facing that problem as well
i cant search anything cause it always starts with that stop code
Mine is on a fresh install…Can’t access windows a at all
Is it bad that I have 721,000 files in one hard drive?
You start with press the cortana search box...but my pc cant get passed (your device run inti a problem) so i cant press anything....now what do i do ?
Hi there, thank you for your question. If your PC is stuck on a "your device ran into a problem" error screen and you can't access the Cortana search box or any other functionality, you'll need to perform some troubleshooting steps to try and resolve the issue. Here's what you can do:
Restart Your Computer:
The first step is to perform a forced restart of your computer. Press and hold the power button until your computer turns off. Wait a few seconds, and then turn it back on. This may help clear the error.
Safe Mode:
If your PC continues to encounter the error and won't boot normally, try booting into Safe Mode. To do this, turn off your PC and then turn it on again. As soon as it starts to boot, repeatedly press the F8 key or another function key (depending on your PC's manufacturer) to access the Advanced Boot Options menu. From there, select "Safe Mode." Once in Safe Mode, you can attempt to diagnose and resolve the issue.
System Restore:
If you have previously created a System Restore point on your computer, you can try to restore your system to a point when it was working correctly.
To access System Restore, you can try the following steps:
Boot into the Advanced Boot Options menu as mentioned in step 2.
Select "Repair your computer" and follow the on-screen prompts to access System Restore.
Dude,you tell me,go and see if drivers are corrupted,but i cant,my pc reastarts over and over with the same error
Could it be hardware issue like bad connectors, thermal paste etc? And how does one clean un/install drivers? Cause my PC gives me this error when I boot up minecraft or deep rock galactic.
Additionally when doing the check disk option I tried doing it with my C: drive and it said it is NTFS?
Hi there, thank you for your question! Yes, it definitely could be caused by any of those issues you listed, I would recommend trying a cpu/gpu temperature monitor to see if you get high temps when playing, Also try checking your task manager to see how the usage is for each components.
How to use when I cant even access dekstop
Hi I wanted to ask what to do if i cant Use arrows on my laptop how do i need to navigate there i can do only up left and right
Corrupt drivers - windows update was clean, system security is up to date and fine, ran a sfc/scannow came back ok, gpu drivers are up to date.
System files damaged? how?, i was just watching a youtube video thats all and anyhow i already ran a scan system program which came back negative for corrupt files.
Incompatible drivers? i havent installed anything.
CPU overheating...hmmm, it's possible but dountful seeing as i have 120mmAIO with fans in a cool room with a low overclock, but it's possible.
Faulty hardware componant issues, also possible because my gpu has been playing up lately.
Third party application, dountful.
Ok, so it's either my CPU which i can remedy by turning off my O/C and see how the system runs or it's my gpu :(
Hi there, thank you for your question! Sometimes even a simple overclock can cause the issue id recommend removing the overclock and see if the issue stops.
so the chkdsk command doesn't continue due to: "Chkdsk cannot run because the volume is in use by another process."
Type j and restart
Thank you uncle it's worked🤗
uncle 😂😂
You indicated that the IRQL stop code is often associated with a driver problem. Accordingly, which of the various approaches would help identify the driver and repair it?
Hi there, thank you for your question. You can try: 1. Check the error message: The IRQL stop code error message often includes the name of the driver causing the issue. Make a note of the driver's name and search for its updates or fixes.
2. Use Windows Event Viewer: Open the Event Viewer to check for any error logs related to the driver in question. This can provide more information about the issue and help you identify the problematic driver.
i just fresh install windows 10 and after playing valorant (using discord) also my pc getting bsod not equal? what happen? its new install
The corrupt registry files one found a few and corrected them... then it did it again. I am absolutely stumped and have done everything from this video. Hardware is fine. No clue, any help?
Hi there,
Could you please elaborate on your question? We're glad to help.
I can't even turn the laptop on, it keep me booting then bluescreen then booting then bluescreen
Hi there, thank you for your question! You may need to use a recovery drive or installation media to repair your system files rebuild the boot configuration data, or perform a startup repair, as not even being able to access the computer could indicate further issues so I would recommend taking it to a professional for further assistance.
thank you.. very informative and useful 😉😉😊😊
my cpu was just overheating, maybe just consider to clean your pc, lower the clock speed or CAUTION: adjust the cpu temperature emergency power off threshold (the last one could damage your cpu, if done wrong)
Please help me solve this blue screen stop code driver irql not less or equal What failed: NVME.sys
My laptop isn't starting after this error restart , I need help
Hi there, thank you for your question! If you laptop isn't even turning on I would recommend trying to use a bootable USB drive and see if that works otherwise I would recommend taking it to a professional as it might be an internal issue.
Please I need help, I'm from Brazil, I paid for the program, but the download doesn't start.
(i sometimes comment first before watching the video).
This just happened to me, just watching a youtube video and then out of the blue blam! this came up? wtf....anyway, lets watch the vid..
I have a question about Can I reinstall windows again will it fix the problem
Hi there, thank you for your question! Reinstalling windows should hopefully solve your issue.
@@RecoveritDataRecoverySoftware thanks for answering my question. Because i accidentally removed the cmos battery then this problem happened and I have tried restart several times but this problem and other blue screen problem happened . Thanks 👍
Thank you gor helping solve this problem. Sfc /scannow helps
how can i be able to enter the windows to run system restore while im having boot issues that doesnt even lets me to get access to my pc. i tried formating but my pc doesnt boot on the usb, i did the boot order as usb setting on the top and also it says on bottom of the driver irql not less or equal, what failed: ACPlsys. can anyone help me?
Hi there, thank you for your question! The error message you received indicates that there is a problem with the driver ACPlsys. This error can be caused by a variety of issues, including corrupted system files, faulty memory, or a corrupted hard drive. You can use the Windows Recovery Environment (WinRE) to resolve boot issues with Windows 10. To access WinRE, you can interrupt the boot sequence by pressing the power button as soon as the Windows logo appears. Repeat this process two more times, and on the third interruption, Windows 10 will open into the recovery environment. From there, you can use the “Startup Repair” tool to fix booting issues with Windows 10.
Explained in detaila
Hi there,
Could you please elaborate on your question? We're glad to help.
Wow thank u so much 😊💯 solution 4 fix my issue 🎉
My Pc is newly upgrade, and the stop code error " IRQL NOT LESS OR EQUAL " always pop up randomly. Like 5 days gap. What seems to be the problem in my PC? (The sfc scan found a corrupt files and fixed it) it should be ok then?
Hi there, thank you for your question! It may not necessarily resolve the issue if the root cause is elsewhere. Check for Driver Issues by ensuring all drivers are up to date, run a Memory Test to check for RAM problems, keep Windows updated, and inspect hardware for loose or faulty components. Revert overclocked settings hope these steps help.
what if i cant even get into windows safe mode? i cant even get a windows logo before the BSOD
What to do when my bluescreen is still loading...
dumb question but how do you enter c: ?
Help. Mine has hardware problems detected.
i get this error every minute and still not fixing with those fixes
its working if you can get in win but what if windows dont load during this error?
Hi there, thank you for your question! If Windows is not loading during a no display error, you can try checking your hardware connections, connecting a different monitor, booting into Safe Mode, using System Restore, using a recovery drive. Accessing these options may require accessing the BIOS or UEFI firmware rather than from within Windows itself.
I just tried install a new operating system and it keeps giving me this error on the loading process. With your options I have tried most of them which I can and it still posting the same error ⚠️.
Is there anything I can do again apart from what is in this video
It might be your RAM
@@vcommandarv5916 I tried ram/hdd but still same problem
@@AMNOWTECHhave your problem resolved?
Because mine also have same problem
@@shivambhardwaj1137 no Bro
How about windows 8.1? but can i still do this like what you said about those im usually having this error on my windows 8.1 but i hoped this will work
Hi there,
Could you please elaborate on your question? We're glad to help.
I'm using a Lenovo laptop which I downgraded due to this error and it still exists. I'm not sure how to fix it
Hi there, thank you for your question! To fix this error, you can start by updating your drivers, especially your network drivers. You can also run a hardware diagnostic test to check for any issues with your hardware components. If the error persists, you can try running a system file checker scan or performing a clean install of Windows. It's important to note that the downgrade may not have solved the issue since it could be related to hardware or software problems.
Same here
Why this problem is appeared.
I get this code after I spit beer on my PC
What if it does not go to windows? Just hang on that blue screen
Hi there, thank you for your question! If you're unable to get past the blue screen of death, you can try starting your computer in Safe Mode. To do this, restart your computer and press the F8 key repeatedly until the Advanced Boot Options menu appears. From there, select "Safe Mode" and try the steps in shown in the video again.
Nothing works ! Anything else?
Hi there, thank you for your question! You can search for a tool called windows memory diagnostics in the search bar and choose the restart and check for problems. I would also recommend making sure all your components are correctly connected such as RAM and making sure nothing is loose. If none of those work trying rolling back your pc to a previous version hopefully that helps.
Thank you so much this help a lot
window 10 just trash with all the error just go on with it. and just get blue screen
Thanks for helping me out whit this error
fun fact: typing cmd in search will bring up command prompt :)
My system just shows that blue screen
Love from Pakistan❤
Looks like mine caused bitdefender
Thankyou!!! a very informative video
Glad it was helpful! Please subscribe our channel.
what if my disk is locked
Hi there, thank you for your question. try restarting your computer as it may resolve the issue. Secondly, make sure your Windows operating system is up to date by checking for updates and installing them if available. Thirdly, check your hardware for any faults by ensuring all components are securely connected and running a diagnostic test. Fourthly, run a virus scan as malware or viruses can cause the error. Finally, if your disk is locked, follow the instructions provided by your disk encryption software to unlock it. If these steps do not fix the issue, consider seeking the help of a professional technician or contacting your computer manufacturer for further assistance.
Mine turned out to be a bad monitor (Driver compatibility I assume). Switched monitors, bam, no more problem. Also, check your HDMI cable.
Help! My laptop got really wet on the rain 2 days ago and it's working but the screen is back what should I do??
I don't want my mom to know it please!! If you know make a video
3:28
Super sir 👍👌
Glad to hear that! Please hit the subscribe button.
Amazing 😍
Glad to hear that! Please hit the subscribe button.
I can't run the disk check command because it says 'the volume is in use by another process', how am I supposed to check it?
Edit: I also ran the memory test, and it said there were no memory errors found, but I've gotten 'memory management' error codes before along with the irql code. This doesn't make sense to me.
Edit 2: I also ran the hardware diagnostic test and found no errors, yet I'm stilling getting the error code when I'm trying to download games. Someone please help me I have no idea what's wrong, I can't download anything...
The same with me
The exact same thing with me when I download games I get blue screen of death I just want to play
Did you find a fix?
@@BLUZLE. I just had to test my ram and re-download the latest nvidia drivers. So far it's been working fine. So I had some bad ram if I had to guess
@@Mike-pd6np did u just download nvidia drivers or u replaced it?
the only what helped me is disabling Virtualization Technology in bios
I have code(rndismp6.sys) what do i do
But, how if my Computer cannot display after this bsod
That’s what I’m saying
U should check it with bluescreen wiever mine caused bitdefender security
i have bought an IBM System X server and i get this error when loading the Bootable USB with Server 2022. if the discs are not setup in raid i dont get the BS, but then ofc i cant see the discs.. as soon as i set my discs up in raid 5 i can no longer reach the installation before BS "storport.sys DRIVER IRQL NOT LESS PR EQUAL" please, do you have any advice?
Hi there, thank you for your question! Try to update the bIOS and chipset drivers this might resolve your issue.Check if the BSOD errors are caused by "stornvme.sys" and update the driver if necessary. Lastly try Downgrade the HPCISSS2 driver to version 62.24.2.64
@@RecoveritDataRecoverySoftware thank you for the reply, i fixed the issue though, i had to, as you just said, update the bios to the 2018 release, and i had to inject the raid controller drivers during the installation. i had no luck with server 2022. so im running 2012 R2. thank you again
i deleted a program file and idk which one it is and it won’t let me restart my pc