Can't wait to see this car on the track. I think you and RK Tunes have two of the most wild F80 M3's on RUclips. Excited to see how it smashes out 1/4 mile passes.
Hey Brian, congrats on your build!! You know what would be an awesome project? Swap the tranny for a ZF 8HP70/75 and convert it to AWD. People have been going crazy with these swaps, puting that 70 on everything, including e46s, e90/92s, and many other brands with the Lamik TCU. But no one has done an AWD conversion. On this F80 you won't need the controller, it's almost a direct swap with an adapter plate and a slight mod, but many have done it!
@@MistaaFrosty fun project, and cheaper than building the tranny. It would get lots of views if he was to do it and turn it into an AWD. There's a reason of why BMW used that tranny on the new M5s;)
No expense spared! Insane, though with a built motor I would expect redline to be 8K or even higher, looking forward to how you set this up for the street.
Don’t need a different dyno bro. Just need a higher gear. You have the DynaPack 3000 pods I assume ? If so, they have a software upgrade to 4500 nm. We’ve measured almost 1300 lbs.ft with it.
It maxed out at 3,320 lb-ft (4,500 Nm) at the hubs. The maximum capacity of this machine is 1547 WHP at 2450 hub RPM. So 1200-1400 WHP is not a problem with the correct gear ratio. And yes, he just needed to shift into a higher gear :|
Finest f80 i ever seen. Wy do you dyno it in 4. Gear? If you dyno it in 5. Gear and put the diff ratio in the dyno at the corect number 3.46 the dyno will tolerate more power. Because the torque on the wheels will be less.
Hey there Brian, I'm going to be that one smart as guy ha, but for the sake of knowledge. Torque has a measurement unit of lbf-ft, as opposed to ft-lbf, for the reason that torque is measured in force at a given radius. As for where these dyno torque numbers occur within the drivetrain, typically torque measurements from a dyno are at the flywheel or output shaft, as opposed to the wheels (wheel size, gearing ratios, etc. are information input to get these dyno torque numbers). If torque were measured at the wheels, the value would be significantly higher because the radius of the entire wheel would contribute to the calculation and increase the output number. GM did this with the Hummer EV with their wild 11,500+ torque claim, which was quite confusing and initially unbelievable since torque values are rarely measured at the wheels. I do not mean to offend in anyway, just wanted to share a bit of engineering knowledge, which you probably knew all this already. Continue the great work, the project is truly fascinating and entertaining to watch. It looks like you guys hit the 1,000 crank-HP goal (assuming ~15% drivetrain loss) 😃
What? The F80 broke your dyno, that’s a first on RUclips 😂😂 that’s one way to sell your services you’ll have everyone outside your workshop tomorrow wanting to upgrade their BMW M cars 😉 absolutely fantastic video.
Great great video!!!! I just flashed my F80 with BM3 93, and seems to work fine. But this is another level! Damn what a dream.. I hope you'll make same build for a F90. They have some pretty big fan groups on facebook!
Brian just curious i have the same build as you minus the port injection but have just about everything you do and Phil from HKP can confirm.. so did you get to 850hp on the Mousselman without the PI connected? just curious as im about to take the car to get everything installed.
Hey @kiesmotorsports can u list or create a page for all mods needed to support a n55 ps2 like plugs fuel pumps and what ever else is needed to keep the card reliable??
Port injection not needed. I can see you really don’t want to do it. I’m 700 on Mosselman turbos, M5 injectors, stock motor, stock fuel pump and stock cooling. I had PI but never installed it nor meth. 28psi. I was playing if safe 2 years ago lol I need to turn it up now. Oh and 98oct.
🇧🇷🇧🇷🇧🇷🇧🇷👏🏻, while I’m insane amount of power your M3 f80 has. What an awesome video! Ethanol is the way to go burns cleaner burns cooler blah blah blah blah blah blah! Maxing out the Dino that was so funny! Horsepower might’ve been through the roofs…
😳 Watching the spider walk around on the door at 8 minutes. This build is super nice and a huge goal for my F30 ActiveHybrid 3
You guys should make that 8 minute spider your mascot!! Maybe come up with a good name!
8-I I didn't even see that first time. Welp, gotta burn the car down.
Excited like a little kid when I saw this video drop!
Edit: note the spider at 8:06 LOL
Switch to a different gear. That will drop the multiplier and spin the hubs faster so you’ll get past the torque limit
Honestly one of my fav series on going rn, very informative and the production quality is always top notch. Glad I found you guys through Nour👍🏼
One mod did mentioned: weight reduction (that haircut of course)
Can't wait to see this car on the track. I think you and RK Tunes have two of the most wild F80 M3's on RUclips. Excited to see how it smashes out 1/4 mile passes.
This haircut fits you better.
Time for a built Dyno 🤣
Hey Brian, congrats on your build!! You know what would be an awesome project? Swap the tranny for a ZF 8HP70/75 and convert it to AWD. People have been going crazy with these swaps, puting that 70 on everything, including e46s, e90/92s, and many other brands with the Lamik TCU. But no one has done an AWD conversion. On this F80 you won't need the controller, it's almost a direct swap with an adapter plate and a slight mod, but many have done it!
why would you swap a dct for a zf lol. just build the dct and get the faster shifts.
@@MistaaFrosty fun project, and cheaper than building the tranny. It would get lots of views if he was to do it and turn it into an AWD. There's a reason of why BMW used that tranny on the new M5s;)
@@MistaaFrosty for launching. Launching with dct sucks.
ICON headlights would finish this off 😍
Definitely feel like he’s being conservative even at “peak power” that car definitely has more to show. Very exciting.
Amazing numbers! Congratulations to everyone involved!!
Spider photobombing the shot lol
Watching this video, I just realized it’s amazing how far you’ve come. Congrats 👏
Nice!! Time for a bigger dyno 😎👍🏻
6 months later and still waiting on the Part 6 where u run on bigger dyno haha or am I missing something and there is a video of it
Dayum!
That's awesome man. Taking the dyno to the limits... Nice!
Nice hair cut bro! Looks so much better
No expense spared! Insane, though with a built motor I would expect redline to be 8K or even higher, looking forward to how you set this up for the street.
I mean did you see the cost of the 35k seats?! 🤣
@@MiniMatticus think they got it for less than 10 luckily
Just awesome guys! Keep up the amazing work!
Don’t need a different dyno bro. Just need a higher gear. You have the DynaPack 3000 pods I assume ?
If so, they have a software upgrade to 4500 nm.
We’ve measured almost 1300 lbs.ft with it.
It maxed out at 3,320 lb-ft (4,500 Nm) at the hubs. The maximum capacity of this machine is 1547 WHP at 2450 hub RPM. So 1200-1400 WHP is not a problem with the correct gear ratio. And yes, he just needed to shift into a higher gear :|
Finest f80 i ever seen. Wy do you dyno it in 4. Gear? If you dyno it in 5. Gear and put the diff ratio in the dyno at the corect number 3.46 the dyno will tolerate more power. Because the torque on the wheels will be less.
Watched the whole thing! Love this series. Let’s goooo!
Hey there Brian,
I'm going to be that one smart as guy ha, but for the sake of knowledge. Torque has a measurement unit of lbf-ft, as opposed to ft-lbf, for the reason that torque is measured in force at a given radius. As for where these dyno torque numbers occur within the drivetrain, typically torque measurements from a dyno are at the flywheel or output shaft, as opposed to the wheels (wheel size, gearing ratios, etc. are information input to get these dyno torque numbers). If torque were measured at the wheels, the value would be significantly higher because the radius of the entire wheel would contribute to the calculation and increase the output number. GM did this with the Hummer EV with their wild 11,500+ torque claim, which was quite confusing and initially unbelievable since torque values are rarely measured at the wheels. I do not mean to offend in anyway, just wanted to share a bit of engineering knowledge, which you probably knew all this already.
Continue the great work, the project is truly fascinating and entertaining to watch. It looks like you guys hit the 1,000 crank-HP goal (assuming ~15% drivetrain loss) 😃
m3zcp with dct and e-lsd only 6% whp loss if I'm not wrong. dynod a stock m3c 421.7whp
damn good thing you brought it to the dealership to change the oil.
Looking forward to seeing this car on the road against lambo´s, gt-r´s and killing them all 😈! flawless!
Only problem is those cars got AWD
I have like no grip til 3rd gear with just a stage 1 ⚰️
That thing is so quiet and smooth 👍
Maybe time for an Aussie built Mainline hub dyno 💪💪
Awesome
Thank god you've finally had your hair cut, you were looking like the kids from Hanson 😂😂
That spider at 7:50
soon as I saw the spider around 8:00 I came to the comments and wasn't disappointed lol
8:00 well hello
Do a quick check if you can use a higher gear and keep the axle speeds within spec. That will drop the axles torque and you should hopefully be fine.
I just noticed you cut your hair, knew something was off 😂😂
Hey, nice haircut!
100,000 in upgrades 😳😳😳
This is a monstrous build!
Sir I appreciate your work ! Greta proyect and great content as alway ! 👍
What? The F80 broke your dyno, that’s a first on RUclips 😂😂 that’s one way to sell your services you’ll have everyone outside your workshop tomorrow wanting to upgrade their BMW M cars 😉 absolutely fantastic video.
Waiting for the other dyno run
Great great video!!!! I just flashed my F80 with BM3 93, and seems to work fine. But this is another level! Damn what a dream.. I hope you'll make same build for a F90. They have some pretty big fan groups on facebook!
My boy wanted a closer look at the M3 8:00
The hair looks great!
Ayyyy you finally got a haircut bro, more weight saving in the car now 😂
YEEEEEAHHHHHHH BUDDY
Man those brakes 😍..💯👍
You’re doing God’s work Mr. Kiefer.
this engine is beast as always.. sheesh
Did you guys ever update numbers on this?
Guys when's the next vid for this build? I'm dying here!!
What a awesome build 🤌🏾👏🏾, can’t wait for the how much $$ was my 1000 Hp F80 video.
Man you look good 👌
Holly sh-t bru that is a beast
When are you gonna find out the true results and the next video to this please?
How much psi on the e90
Mosselman turbos?? I thought this was going to be a Kratos turbo build?
Do you guys still have the factory cats? How much HP would you say the factory system is before you would have to upgrade?
awesome bro 👏 Baraboo God bless
Brian just curious i have the same build as you minus the port injection but have just about everything you do and Phil from HKP can confirm.. so did you get to 850hp on the Mousselman without the PI connected? just curious as im about to take the car to get everything installed.
Did this series get scrapped cuz i wanna see the rest 😢
What gear are you running?! Its says 4.0 in final gearing? Just run a higher gear
Hey @kiesmotorsports can u list or create a page for all mods needed to support a n55 ps2 like plugs fuel pumps and what ever else is needed to keep the card reliable??
8:00 spider
Whats with the loop on the start of the dyno sheets
Port injection not needed. I can see you really don’t want to do it. I’m 700 on Mosselman turbos, M5 injectors, stock motor, stock fuel pump and stock cooling. I had PI but never installed it nor meth. 28psi. I was playing if safe 2 years ago lol I need to turn it up now. Oh and 98oct.
Next video should be race with hoonicorn
Hell ya such a good video hahaha
did you upgrade the transmission, axles, and drive shaft?
So if you don’t mind answering which turbos are better and bigger the pure turbos or your turbos?
Are you using the port injection on the 93 tune?
Is this a custom tune?
Wow 😮
Spider!!!!
polepositions(seats) would be cooler and lighter option
How's it like to drive on the street?
Are you doing 3rd or 4th gear pulls? Just curious…
FINALLYYYY 🙏🏾
Awesome problem to have. The f80 sounds so tamed
Savage AF😎🤘🏻🤘🏻
I need a link to the wing on the black m3😭
No one nothing, me asking:
Is the Blue BMW behind you an F80 with a swapped M2 comp. front bumper ?
335, got it from the video now, sorry :D :))) stupid question
Updates ?
Exceeding a dyno torque limit is nuts 😂😂😂😂😂
Spider-Man wants his car back 🤣
🤯
Very impressed. Good stuff
When is the next video ?
Mod list?
What happend to this car? Never got finished?
Would it possible to get 550WHP out of my N20? If I were to build it
Not without spending a lot more money than it’s worth. You can just get an M car for cheaper and upgrade it to 600-700 HP
Where is part 6? 😢
Remember hp doesn't matter but torque does high torque fast car, high hp low torque slow car
part 6????
Someone's going to need a good tire.
now i wonder what is the highest HP/Torque i can achieve on my f30 320i n20 engine 😅
Without building 260hp😂😂😂😂😂
Shoulda went with the 328 stage 2 fbo you’re at about 350-380
328 stock you’re at 320s max tuning capacity
None
I feel you on that. I have a N20 and I want to hit 300 hp safely
What happened? We never got to see the goal
You gonna raffle off the f80 eventually? I'll buy 100 of everything for a chance to win
🇧🇷🇧🇷🇧🇷🇧🇷👏🏻, while I’m insane amount of power your M3 f80 has.
What an awesome video! Ethanol is the way to go burns cleaner burns cooler blah blah blah blah blah blah! Maxing out the Dino that was so funny! Horsepower might’ve been through the roofs…
“What is the next point of failure?” Oh, the Dyno? Ok, ok.