Development of surfaces 5 | Cone | Engineering Graphics | Truncated Cone

[@priyashah9466]

Short and best, thank you sir, it will help me in my today's exam👍

[@MechTechSimulations]

Thank you. Subscribe and share it to your friends👭👬

[@avirajyadav7873]

Me too

[@harshsingh8619]

cone of 50 mm diameter and height 70 mm is resting on its base. It is cut by a cutting plane inclined at 45° to the HP and it bisects the axis of cone. Draw the development of the lateral surface of the truncated cone.

[@abulhassan1391]

Thalavian vera level 🔥🔥🔥🔥🔥🔥🔥🔥

[@mutumbishamutakwa270]

great video but when drawing the surface development just get division of the circle in the plan and mark 12 times to get your divisions

[@MechTechSimulations]

Yes, drawing 12 divisions will give a better accurate development

[@vijayalaxmi4716]

Super class I can understand ur class.......

[@MechTechSimulations]

Glad to hear that

[@veeraajay6433]

Simple explanation.... Keep going...

[@MechTechSimulations]

Thank you, I will

[@xaviersuresh]

Very useful. Learned it joyfully..

[@MechTechSimulations]

Glad to hear that

[@TauFiq.B]

sir today we had same question in exam only difference was, it was given right circular cone ? is it same

[@MechTechSimulations]

Exactly! What I have drawn in this video is a right circular cone. Congrats..

[@kergeysarjakin5592]

loved ur videozzz thankuuuu

[@MechTechSimulations]

Thank you so much..

[@cosmicgarou99]

Thank you very much sir 🙏🙏🙏🙏🙏

[@MechTechSimulations]

So nice of you

[@noobgaming0567]

sir it is fav subject
thank you sir

[@MechTechSimulations]

Thank you Rohith. Subscribe and share it to your friends.

[@dharanbalaji]

Wonderful sir

[@AdarshChaurasiya3146]

Thank You Sir for explaining 👍👍❤️

[@MechTechSimulations]

Always welcome. So nice of you. Subscribe and share it to your friends.

[@AdarshChaurasiya3146]

@@MechTechSimulations Ok Sir 👍👍

[@sstewartsideways]

Thank you for the video! Can you please tell me how I would figure out what angle I would have to make each of the bends in the stretchout to make this pyramid?

[@MechTechSimulations]

What do you mean by the bends? Do you mean the angle between each segment in the whole sector? If yes, that will be one eighth of the whole angle.

[@srijayschannel9293]

Sir shall we use the same answer for truncated cone, diameter and height are different pls tell me sir

[@MechTechSimulations]

Yes, the same procedure is to be followed to draw the cone. Then we have to transfer the cut points.

[@artisticgate]

Draw the projection of a right circular cone of base 80 mm diameter and height 90 mm resting with it’s base on H.P. and 50 mm in front of V.P.

[@pradeepkumarmec0347]

Tq good explanation

[@MechTechSimulations]

Welcome..

[@aleenaantony1681]

Thank you sir.Nice lecture

[@MechTechSimulations]

Thank you.

[@powerstar2109]

Top view and front views

[@mayurdandekar4078]

Sir how did u get a 45° by using a scale

[@MechTechSimulations]

I've drawn it approximately. Have to use a protractor or mini drafter.

[@mayurdandekar4078]

OK sir

[@vedikashinde9995]

Given in question draw side view so development is not based in side view?????

[@hrithikadas9063]

Thank u very much

[@MechTechSimulations]

You are most welcome

[@sabrish4632]

Super

[@MechTechSimulations]

Thank you. Subscribe and share to your friends.

[@Student-t3z]

How can we contact with you sir

[@MechTechSimulations]

[e-mail]

[@shashankchatla9191]

thank you sir

[@MechTechSimulations]

Most welcome

[@rudrarudresh6213]

Good sir

[@MechTechSimulations]

Thanks and welcome

[@chiratidzochashemudonhi6345]

The best

[@MechTechSimulations]

Thank you for the appreciation.

[@fahimasultana5371]

Sir how you divide this 142 angle into 2 part? Please help

[@MechTechSimulations]

Sorry for the delayed response. As mentioned in the video at 3:10 cut an arc from both the ends of the sector. Then from the intersection point of both the arcs, draw a line to the centre of the sector.

[@terythumati7226]

Qs ledlkunda cheptunnaru qs vunta inkonchem ardhamandhii sirr.

[@MechTechSimulations]

I couldn't understand.

[@saeedahmed510]

How make eccentric cone

[@balikannaujia943]

Ausome

[@MechTechSimulations]

Thank you

[@Abc-zy6fi]

Sound clearly nahi hai

[@MechTechSimulations]

Thanks for your feedback. I'll do better in future videos.

[@RajKumar-nu9oh]

Sir jee y barnch fabrication banaye

[@powerstar2109]

Answer pettandhi sir questions ki

[@paragchaudhary38]

Thanks 😊

[@MechTechSimulations]

Most welcome. Please subscribe our channel and share it to your friends.

[@tharakagimhan4909]

❤️