I have family of engineers who constantly whinge at these methods. But i find them fascinating. In Australia people in the desert centre are known to use fencing wire and post to fiz suspension etc and it works for them. You guys are excellent welders and spot on measuring. Please keep going as many of us love it. I lived years "off road" and people in town wouldn't believe things i did.....their loss.
It kindof depends on what caused the failure. If something very unusual broke it then the repair is probably fine for normal operating conditions. At any rate, it was well done considering the tools available.
Ładne spawy niestety osiowość mierna jeśli takimi metodami uzyskali bicie na poziomie 0.5mm to bardzo dobrze. sądząc po kształcie elementu prawdopodobnie jest to jakiś bęben hamulcowy, a po spawaniu nie został przetoczony. brak pomiarów, brak osiowania, wiercenie otworów ręczne (powinno się to odbywać w podzielnicy a nie na oko) jakiś czas podziała ale jaki inny element przy okazji zniszczy to zagadka.
Whatever they say but, there is nothing so good as licking the sweat from your brows [ preverably by a lovely wife] after a hard days works when you can say "I created that!" That's life at it's rawist point.😊
Love From bangladesh 🇧🇩🇧🇩🇧🇩🇧🇩
And take care of your health 😊😊😊
I have family of engineers who constantly whinge at these methods. But i find them fascinating. In Australia people in the desert centre are known to use fencing wire and post to fiz suspension etc and it works for them. You guys are excellent welders and spot on measuring. Please keep going as many of us love it. I lived years "off road" and people in town wouldn't believe things i did.....their loss.
Not to take away from their innovation but just make it work isn't the same as make it last.
Probably it will last more than a new part
Again, a non expert pissing on something with no content on their channel.....
Bodoh kamu.. Justru buatan pakistan tersebut lebih kuat dari aslinya
At this point work is probably more important than last.😊
It kindof depends on what caused the failure. If something very unusual broke it then the repair is probably fine for normal operating conditions. At any rate, it was well done considering the tools available.
Es un genio me encantan sus videos desde Costa Rica américa central
top bit of welding and lathe work. 👍👍👍👍👍
Muito bem trabalho excelente. 👏👏👏
Welding in open for sandals !
Que profissionalismo!
Great work again. Why do you put that blue marker on the item you are going to put threads on?
To check the depth of the treads. eyeball work.
@@glennschemitsch8341 Thank you Sir.
Nice ❤❤❤❤❤❤❤
The best
TRIỆU LIKE 👍👍👍👍👍👍👍👍
Ładne spawy niestety osiowość mierna jeśli takimi metodami uzyskali bicie na poziomie 0.5mm to bardzo dobrze. sądząc po kształcie elementu prawdopodobnie jest to jakiś bęben hamulcowy, a po spawaniu nie został przetoczony. brak pomiarów, brak osiowania, wiercenie otworów ręczne (powinno się to odbywać w podzielnicy a nie na oko) jakiś czas podziała ale jaki inny element przy okazji zniszczy to zagadka.
Again, a non expert pissing on something he knows nothing about...
@@peatmoss4415 Care to state what YOU are "Expert" in?
Como tendra los dedos y manos este hombre los ojos los salva con esos lentes opticos
Great job
Bu usta çözüm bulmada çok zeki.
👍
👍👍👍👍👍
That break looks a little too clean to be a genuine failure
Whatever they say but, there is nothing so good as licking the sweat from your brows [ preverably by a lovely wife] after a hard days works when you can say "I created that!" That's life at it's rawist point.😊
This temporary work because of bad welding repair, surface welding won’t last longer, it must be deep V groove welding to hold better and last longer.
You’d be jailed if you did that in the UK. Scrap it for everyone’s sake, it’s a failed part. Probably a casting defect.
In the US such repair procedure is not accepted at all , because these heat treated gears and once exposed to weld , it became malleable and brittle .