This was a SUPER good tutorial.... If I can add ONE thing to this video it is this..... when you take the plenum off and you have exposed the six lower intake manifold runners. You should REALLY consider covering that up with a rag or tape while you are working... cuz if you drop ONE bolt or socket or ANYTHING metal into one of those runners..... BYE BYE motor..... you are gonna have a serious problem if something small drops into one of those holes BEGGING for something to be dropped into. The law of Mr Murphy.....
Thank you a million times over, im handy with cars and i just picked up a 2005 tucson 2.7l with 186k on the clock, the spark plug electrodes were down to nothing, i was getting a headache over looking at how to access the rear plugs and you just lifted all the weight off my shoulders. Cheers!
Kudos to you sir! I have to dive into this procedure myself but also have to replace a valve cover gasket because it's leaking onto the exhaust manifold. I must say, I have watched a few videos by now on RUclips on the topic and they were terrible! I'm not sure why people even think they should present themselves on RUclips or any other public viewing media? You covered the procedure exceptionally well, easy to follow and very accurate.Thank You Sir!
Thanks a million! I have a 2004 Sonata GLS 2.7l V6. I paid $1000 for it in 2019. It came with 184k miles. Whoever had the car before me kept it serviced. Ive changed the oil twice since. It just hit 196k miles. Work is right down the road and other than that I stop by the grocery store. Without a doubt its one of the best automobiles Ive ever owned. At 52 yrs old, this may very well be the last one. Thanks again for making such an arduous task do-able.
When reassembling, tighten down the front bolts of the intake manifold first so you get a good seal on your manifold gasket or you'll roll the gasket and cause it to leak. Found out the hard way myself.
So, i did this today following the video and would REALLY like to thank you for the very detailed instructions. Well, i said i did it, but actually i got to the point of putting the plugs in, ran out of daylight shortly after so going to put it back together tomorrow. For anyone looking to do this job yourself i have some input: Those back three bolts...one is easy, and as you pointed out, the other 2 are blind, you can't see them at all...Infact most of the time it took me to do this involved the middle and right bolt (the left one you can see as he said), the other timesink involved the "vacuum lines" under the throttle body. This took me 3 hours, and it was on a 2.7l Santa Fe, but its the same engine and judging from the video the rear is just as cramped in a Santa Fe as it looks in a Sonata. But yea, THANK YOU VERY MUCH FOR THIS VIDEO, IT HELPED TREMENDOUSLY. ^_^
about those little metal clips on the electrical connectors. just so you know you dont have to pry them off, simply press down on the metal clip and pull the connector off....then you dont have to worry about losing them. Your Welcome!
I just did this yesterday on my wife's 2005 Sonata. This video helped immensely. I did not have any issues removing the plugs. However when I put the new ones in, the black rubber grippy grommet in my spark plug socket kept coming out and staying on the new plugs. It was a pain to get out of each spark plug well. I did break a short (4"-5") vacuum tube that attached to the plenum since it was brittle. 5/32" was the replacement hose that I bought. Some of the wire aligners/separators /holders broke because they were so brittle. I bought a 1.5" 3/8" extension for the back right and left rear plenum bolts per the video. I also found my 10mm ratcheting wrench handy for removing the bracket that holds the cruise control and throttle cable. Thank you for the awesome video.
At 9:35 you pulled off an electrical connector from the throttle body. Mine had two of them side by side that were exactly the same connector. Switching them when putting it back together caused it to run rough, not shift, and through a few codes. Took me a while to figure out what I did wrong. By the way, you made this job look easier than it really is. Great video and thank you for doing this.
Going to replace my spark plugs tomorrow, super nervous but if I can fix and build computers, I'm sure I can disassemble some car parts. Great vid! TY!
I love this video and this guy. I watched two others where they did not totally remove the plenum and they had to work at ridiculous angles while the plenum was raised up with boards.....it was not that time consuming to remove the plenum. Once I saw this video I decided I could do it myself. Thank God I did not try it the way those other guys did - when I got to the center rear spark plug I found it probably has stripped threads, meaning the aluminum head is ruined. I did not remove it all the way, just snugged it back into place and left that old spark plug. The 3 front plugs were bad, the back ones for some reason looked much better. I'll use the car like this while I look for another car. If I had done this the other way i would have assumed the difficulty i was having was from the bad angle I had to use with the plenum in the way, and taken out that plug and probably never gotten one back in. :-(
I just bought a 2004 Hyundai Santa Fe with 90,000 on it, that is in like new condition. After taking off the engine cover I found a rodent nest! I guess Hyundai's are popular with the animals. Thanks for the video, it's going to help a lot when the time comes.
Thanks. Instead of removing the cruise control cable, I removed the two bolts from the bracket that attaches the cables to the air intake manifold. That also gave me more flex-room to get the two hidden rear air intake manifold bolts.
I just followed the video to replace the plugs on my daughters 2005 Tiburon V6. Worked great! I did NOT need to remove any cable lines. Just unbolted the bracket. Also didn't need to remove the hoses on the bottom of the throttle body. Maybe the Tib is a little different than the Sonata. I can't believe our car was still running after seeing how bad the plugs were! The gap was huge.
Dude that was very helpful, You explained what's what and how to do it. I just bought a 2002 Hyundai sonata and it needs TLC... brakes, ball joints, front valve cover gasket and both axles. Now I'm starting with replacing intake gasket... Codes say 02 sensor, MAF sensor, or vacuum leak...first im looking for vacuum leaks... Thanks again brother.
I found the back holes on the plenum wouldn't line up... started and snugged up a front bolt and they aligned perfectly. Also I put a piece of blue masking tape on every hose and wire I removed just so I wouldn't leave one off. A small inspection mirror was also useful. Thanks for your help, she runs MUCH better.
Great video!!! Very detailed, and I appreciate how you go above and beyond with the advice about other things to look for while you are in there. (Living things, throttle body cleaning, gaskets etc.etc..etc...) Must respect!!! ( not sure how the air gun couldnt break those nuts, but thats another topic!!! Hahaahha just kiddin my guy😂🤣😂🤣😂🤣😂🤣) much appreciated, keep'em coming!!!!
I've had my wife's 2003 santa fe 2.7l plenum off...this will be the third time. Currently she is at 327,689 miles I believe the two hoses on the bottom of the throttle body are coolant hoses. Don't pull them off without clamping them shut.
Just like a water pump and timing belt always change together, when you get to the spark plugs in a V6 you’re close enough to do valve cover gaskets. Just what I usually do.
Awesome DIY video. You made the job look easy, even though, the job is a pain in the buttocks. Thank you for the knowledge. Also, a lot good info in the comments from some knowledgeable subscribers.
Questions: Do you see a problem removing the back bolts first ? I am asking because if I cannot do that part then I'll quit right then and there without having dismantled the rest. Thanks for taking the time to put this video together. It is REALLY helpful P.S: Note, for future videos, a mirror might help showing hidden parts. I haven't gone exploring yet (it is my girlfriends car), but I am afraid that I might remove the wrong bolts in the back.
Thank you for putting up such a well explained video. Your instructions were right to the letter. M 2004 sonata has 233000 m.i. The last tune up was done by a mechanic? or so he says. He not only put the wires to the wrong coil, but he didn't replace the back bolts. Drivers side and center were not there. After feeling around for about an hour,I got a small mirror and there were no bolts there. I'm sure if he were to watch your video, he would really learn a lot. While this is apart, I will clean all intake hoses and throttle body. Guess if you want it done right , do it yourself with the advice of a real mechanic. Again SIR I would like to thank you.
This is a great video, thank you. Two of the three bolts hold a hose in place. After reassembly I found the loose hose and wound up pulling the rear bolts to reattach the hose.
Thanks some much, this is quality, its vídeo help me, because I bought the kit cables electriplugs and I was trying to change my self but when I remove the screws, surprise its has a lot of silicon and I was too dificult to take the exhaust manifold 😅
While anti-seize can add resistance when applied to the threads, the plug will still make a solid ground at the base of the nut/washer so it really doesn't matter. And the 10k+ volts would render any resistance it might add moot. If you've never had to repair a plug hole your just very lucky. So for 12V grounds I'd agree but for plugs I always use anti-seize.
I just did the plugs and wires and it was a pain in the ass but it was worth it in the end it drives so much better and has a bunch of power i never knew existed on my 2004 hyundai sonata 2.7
YOU DO NOT have to remove the cruise control wire!! I did, based on this video, but after watching several other videos on the same vehicle, they lifted up the air intake system without messing with the cruise control wire at all. Now I have no idea how to put the wire back in place haha. Any tips?
The metal clips on the connectors should not be pulled out ... simply squeeze in on it with your thumbs and pull the connector. It's designed to be super-easy to quick-release the connector.
I just replaced plugs in a 2008 tucson 2.7 and found the easiest way to remove the rear support bolts was remove the throttle control first give you room to get behind with a short ratchet to get the bolts out don;t have remove the throttle cables either .much simpler .
I have a 2002 Sonata GLS with the exact engine and setup. I am going to change the plugs and wires . When you replaced the Plenum gasket did you have to use some gasket sealer or did you just put it in as is ? This video is great and very helpful, I was just wondering about the gasket installation. I enjoyed the video a lot. Thank You
The spark plug is ALSO grounded thru the metal ring at the end of the thread. I gather all the 3.3, 3.5 and 3.8 hyundai/kia lambda engines are extremely tight to get out and most people use anti-seize on them for fear of stripping the head next time they change the plugs.
Thanks for showing me bro👍 I'm going to save $560.00 plus tax for just a tune-up on a Hyundai... 2020.. Yesss😷👍🙏 if I had a girlfriend she will want it.. Lol🤣🤣🤣
I got a kia optima V6 2.7 2006 similar engine got the manifold off but I can't the the spark plug bolt down in the back of engine to remove the plugs do I need a shorter extender?
Thank you 🙏 your Video to a public is easy to learn from you good job thank 👍. but this Engineer is badly Design is it too much work to change others 3 sparkplug .if do the tuneup and change spark plugs you good job 👍
For someone who is not mechanically inclined, it coud have been better. You have to explain every little thing that you do. You take some kind of a metal piece to rub the wire? I couldn't tell if you were saying run or rub. And I wish I knew exactly how much dialectic grease to put in and where. Were you saying boot? What is a boot?
ouu shite after this video I cant wait till the morning to replace my spark plugs. Replacing them always make your car feel like a new machine. My buick was pretty much revived after replacing a few snapped ignition wires and plugs. (surprise it even started i was running on 4 cylinders.) Im excited for this lil repair cause my hyundai really does need it. Got the car for 500$ and its a fixer upper but its a great car
I followed your video and now my acceleration is acting crazy and my rpm is at 1100 in idle and when I drive it’s going all over the place could I have messed with the throttle cable?
Just did this yesterday, put it all together and the throttle linkage is all crazy. Revved all the way up and I had to pull back on the pedal to get it to rev down again. Trying to figure out how to adjust haha
You can just do the plugs, but given the amount of work it takes to get to them, you are best off doing the whole job at the same time. It would suck to have to repeat all your work because a wire went bad. If it's an easy spark plug job, like a 4 cylinder, i am more likely to skip the wires.
Nice video. I wanted to ask if you've tried pushing in the wire clips on the electrical plugs instead of removing them? My BMW wire connectors have a similar wire clip and they just push in and then pull the connector right off. I learned this after several lost clips as they are under tension. Good luck!
I started to take off the wires on the front plugs and can not get them off! I used a wire grip tool and still could not get off. I was afraid to pull too hard or they come apart? Suggestion? Car has 128k on plugs...
Twisting and pulling is your key to success. The wires should be changed since it's such a in depth job anyway so if you mess a spark cable up it's no big deal but twist and pull at same time back and forth it'll eventually come
What is the name of the vacuum hose at 8:49 this hose is disconnected and broke at the tip where it goes at the intake manifold. The car is misfiring could this be the reason?
This was a SUPER good tutorial.... If I can add ONE thing to this video it is this..... when you take the plenum off and you have exposed the six lower intake manifold runners. You should REALLY consider covering that up with a rag or tape while you are working... cuz if you drop ONE bolt or socket or ANYTHING metal into one of those runners..... BYE BYE motor..... you are gonna have a serious problem if something small drops into one of those holes BEGGING for something to be dropped into. The law of Mr Murphy.....
Thank you a million times over, im handy with cars and i just picked up a 2005 tucson 2.7l with 186k on the clock, the spark plug electrodes were down to nothing, i was getting a headache over looking at how to access the rear plugs and you just lifted all the weight off my shoulders. Cheers!
Kudos to you sir! I have to dive into this procedure myself but also have to replace
a valve cover gasket because it's leaking onto the exhaust manifold. I must say, I
have watched a few videos by now on RUclips on the topic and they were terrible!
I'm not sure why people even think they should present themselves on RUclips or
any other public viewing media? You covered the procedure exceptionally well,
easy to follow and very accurate.Thank You Sir!
Thanks a million! I have a 2004 Sonata GLS 2.7l V6. I paid $1000 for it in 2019. It came with 184k miles. Whoever had the car before me kept it serviced. Ive changed the oil twice since. It just hit 196k miles. Work is right down the road and other than that I stop by the grocery store. Without a doubt its one of the best automobiles Ive ever owned. At 52 yrs old, this may very well be the last one. Thanks again for making such an arduous task do-able.
Same best I have over 200k
When reassembling, tighten down the front bolts of the intake manifold first so you get a good seal on your manifold gasket or you'll roll the gasket and cause it to leak. Found out the hard way myself.
So, i did this today following the video and would REALLY like to thank you for the very detailed instructions. Well, i said i did it, but actually i got to the point of putting the plugs in, ran out of daylight shortly after so going to put it back together tomorrow. For anyone looking to do this job yourself i have some input: Those back three bolts...one is easy, and as you pointed out, the other 2 are blind, you can't see them at all...Infact most of the time it took me to do this involved the middle and right bolt (the left one you can see as he said), the other timesink involved the "vacuum lines" under the throttle body. This took me 3 hours, and it was on a 2.7l Santa Fe, but its the same engine and judging from the video the rear is just as cramped in a Santa Fe as it looks in a Sonata. But yea, THANK YOU VERY MUCH FOR THIS VIDEO, IT HELPED TREMENDOUSLY. ^_^
Probably the best how-to diy car repair videos I've seen. And with my unfortunate luck, I've watched a lot of them
about those little metal clips on the electrical connectors. just so you know you dont have to pry them off, simply press down on the metal clip and pull the connector off....then you dont have to worry about losing them. Your Welcome!
I just did this yesterday on my wife's 2005 Sonata. This video helped immensely. I did not have any issues removing the plugs. However when I put the new ones in, the black rubber grippy grommet in my spark plug socket kept coming out and staying on the new plugs. It was a pain to get out of each spark plug well. I did break a short (4"-5") vacuum tube that attached to the plenum since it was brittle. 5/32" was the replacement hose that I bought. Some of the wire aligners/separators /holders broke because they were so brittle. I bought a 1.5" 3/8" extension for the back right and left rear plenum bolts per the video. I also found my 10mm ratcheting wrench handy for removing the bracket that holds the cruise control and throttle cable. Thank you for the awesome video.
At 9:35 you pulled off an electrical connector from the throttle body. Mine had two of them side by side that were exactly the same connector. Switching them when putting it back together caused it to run rough, not shift, and through a few codes. Took me a while to figure out what I did wrong. By the way, you made this job look easier than it really is. Great video and thank you for doing this.
Going to replace my spark plugs tomorrow, super nervous but if I can fix and build computers, I'm sure I can disassemble some car parts. Great vid! TY!
Thank you for this. I like having a V6 but times like this I wish I had 4 cyl
I wish I had a 4 cyl and a mechanic as good as this guy
Also a tip once you find the bolts in the back make a mark on the firewall for future reference! Thanks for your time and help!
Or on the plenum
I love this video and this guy. I watched two others where they did not totally remove the plenum and they had to work at ridiculous angles while the plenum was raised up with boards.....it was not that time consuming to remove the plenum. Once I saw this video I decided I could do it myself.
Thank God I did not try it the way those other guys did - when I got to the center rear spark plug I found it probably has stripped threads, meaning the aluminum head is ruined. I did not remove it all the way, just snugged it back into place and left that old spark plug. The 3 front plugs were bad, the back ones for some reason looked much better. I'll use the car like this while I look for another car. If I had done this the other way i would have assumed the difficulty i was having was from the bad angle I had to use with the plenum in the way, and taken out that plug and probably never gotten one back in. :-(
I just bought a 2004 Hyundai Santa Fe with 90,000 on it, that is in like new condition. After taking off the engine cover I found a rodent nest! I guess Hyundai's are popular with the animals. Thanks for the video, it's going to help a lot when the time comes.
Thanks. Instead of removing the cruise control cable, I removed the two bolts from the bracket that attaches the cables to the air intake manifold. That also gave me more flex-room to get the two hidden rear air intake manifold bolts.
I wish I had done this!! Do you have any idea how to put the cruise control wire back in place?
Very comprehensive video thank you. Kind of rare these days
I just followed the video to replace the plugs on my daughters 2005 Tiburon V6. Worked great! I did NOT need to remove any cable lines. Just unbolted the bracket. Also didn't need to remove the hoses on the bottom of the throttle body. Maybe the Tib is a little different than the Sonata. I can't believe our car was still running after seeing how bad the plugs were! The gap was huge.
This is a LIFE money 💰 saver. Thank you So much
Dude that was very helpful, You explained what's what and how to do it. I just bought a 2002 Hyundai sonata and it needs TLC... brakes, ball joints, front valve cover gasket and both axles. Now I'm starting with replacing intake gasket... Codes say 02 sensor, MAF sensor, or vacuum leak...first im looking for vacuum leaks... Thanks again brother.
I found the back holes on the plenum wouldn't line up... started and snugged up a front bolt and they aligned perfectly. Also I put a piece of blue masking tape on every hose and wire I removed just so I wouldn't leave one off. A small inspection mirror was also useful. Thanks for your help, she runs MUCH better.
Hey I got one too 218k still runs great what you did I did in 2016. People change your oil reg that was a great and informative vid. Australia
Great video!!! Very detailed, and I appreciate how you go above and beyond with the advice about other things to look for while you are in there. (Living things, throttle body cleaning, gaskets etc.etc..etc...) Must respect!!! ( not sure how the air gun couldnt break those nuts, but thats another topic!!! Hahaahha just kiddin my guy😂🤣😂🤣😂🤣😂🤣) much appreciated, keep'em coming!!!!
Thx Bro
You saved me $200 bucks!!!
I've had my wife's 2003 santa fe 2.7l plenum off...this will be the third time. Currently she is at 327,689 miles I believe the two hoses on the bottom of the throttle body are coolant hoses. Don't pull them off without clamping them shut.
Just like a water pump and timing belt always change together, when you get to the spark plugs in a V6 you’re close enough to do valve cover gaskets. Just what I usually do.
Awesome DIY video. You made the job look easy, even though, the job is a pain in the buttocks. Thank you for the knowledge. Also, a lot good info in the comments from some knowledgeable subscribers.
Questions: Do you see a problem removing the back bolts first ? I am asking because if
I cannot do that part then I'll quit right then and there without having dismantled the rest. Thanks for taking the time to put this video together. It is REALLY helpful
P.S: Note, for future videos, a mirror might help showing hidden parts. I haven't gone exploring yet (it is my girlfriends car), but I am afraid that I might remove the wrong bolts in the back.
Thank you for putting up such a well explained video. Your instructions were right to the letter. M 2004 sonata has 233000 m.i. The last tune up was done by a mechanic? or so he says. He not only put the wires to the wrong coil, but he didn't replace the back bolts. Drivers side and center were not there. After feeling around for about an hour,I got a small mirror and there were no bolts there. I'm sure if he were to watch your video, he would really learn a lot. While this is apart, I will clean all intake hoses and throttle body. Guess if you want it done right , do it yourself with the advice of a real mechanic. Again SIR I would like to thank you.
This is a great video, thank you. Two of the three bolts hold a hose in place. After reassembly I found the loose hose and wound up pulling the rear bolts to reattach the hose.
Bravo! Most don't follow through with the reassembly. Big help. Thanks.
thank you for your contribution to the compendium of human mechanical knowledge
Good video. I recently did this on a 2007 Hyundai Tucson V6. It is very similar, except 1 extra bolt in the back and a few more electrical plugs
Thank you ever so much for making this video to help out "MUTE DONKEYS" aka dumb asses such as myself. I can do this. Thank you once again.
Thanks some much, this is quality, its vídeo help me, because I bought the kit cables electriplugs and I was trying to change my self but when I remove the screws, surprise its has a lot of silicon and I was too dificult to take the exhaust manifold 😅
wow man what a great video thanks so much this is really going to help me out!!!
While anti-seize can add resistance when applied to the threads, the plug will still make a solid ground at the base of the nut/washer so it really doesn't matter. And the 10k+ volts would render any resistance it might add moot. If you've never had to repair a plug hole your just very lucky. So for 12V grounds I'd agree but for plugs I always use anti-seize.
Thank you for your detailed video. Great instructions.
OUTSTANDING PRESENTATION (registered HONDA tech emeritus here).
I changed the front 3 @ 112k and it now has 190k and it runs great
I just did the plugs and wires and it was a pain in the ass but it was worth it in the end it drives so much better and has a bunch of power i never knew existed on my 2004 hyundai sonata 2.7
Nice video, Looks like it's gonna take awhile when i try doing it
Aw awesome walkthrough thank you so much for your help man.
YOU DO NOT have to remove the cruise control wire!! I did, based on this video, but after watching several other videos on the same vehicle, they lifted up the air intake system without messing with the cruise control wire at all. Now I have no idea how to put the wire back in place haha. Any tips?
The metal clips on the connectors should not be pulled out ... simply squeeze in on it with your thumbs and pull the connector. It's designed to be super-easy to quick-release the connector.
Thanks so much for the video! Was still a huge PITA. I can see why you only do this every 100k. Took me about 3 hours.
Glad you got it done! It takes me about the same amount of time and i have done it several times now.
I just replaced plugs in a 2008 tucson 2.7 and found the easiest way to remove the rear support bolts was remove the throttle control first give you room to get behind with a short ratchet to get the bolts out don;t have remove the throttle cables either .much simpler .
Thank you sir, very to the point and informative made the job easy!!
Excellent presentation.Thank you.
Very good video. Very helpful. Thank you.
Excellent video. Best I have seen.
i doing my 2003 tiburon tomorrow. thank you for the video. it's not going to be ease. but i can do it
Those clip e connectors can be removed without taking out the wire clip just push down on the clip to release and pull found that out the hard way
thanks that was well done i can do my hyundai plugs now cheers
Thank you for the video....it was very helpful 👌
Haaa i just used your video to refind the cylinder fire order.. i thank you for that as well!
Alrighty, gonna go get this done!!! Thanks for the video
Great details!!! Thanks
I have a 2002 Sonata GLS with the exact engine and setup. I am going to change the plugs and wires . When you replaced the Plenum gasket did you have to use some gasket sealer or did you just put it in as is ? This video is great and very helpful, I was just wondering about the gasket installation. I enjoyed the video a lot. Thank You
I hate it when someone ask him a question. And I too am waiting for an answer. But he never replies.
Great video! Thanks for posting this!
Awesome! Thank you!
Great video thank you sir very helpful
Thank you
Excellent job
The spark plug is ALSO grounded thru the metal ring at the end of the thread. I gather all the 3.3, 3.5 and 3.8 hyundai/kia lambda engines are extremely tight to get out and most people use anti-seize on them for fear of stripping the head next time they change the plugs.
Excellent detail thanks!
how tight does it have to be? until you feel resistance?
Thanks for showing me bro👍 I'm going to save $560.00 plus tax for just a tune-up on a Hyundai... 2020.. Yesss😷👍🙏 if I had a girlfriend she will want it.. Lol🤣🤣🤣
I got a kia optima V6 2.7 2006 similar engine got the manifold off but I can't the the spark plug bolt down in the back of engine to remove the plugs do I need a shorter extender?
Thank you. Spared me a shitty day.
thorough and much helpful, i thank you sir.
A heads up about a torque wrench at the beginning of the video could be cool broke a head and stripped out threads on another
Thank you 🙏 your Video to a public is easy to learn from you good job thank 👍. but this Engineer is badly Design is it too much work to change others 3 sparkplug .if do the tuneup and change spark plugs you good job 👍
Do you happen to have a video on changing the valve cover gaskets?
@@ericpowell9836 not yet, but I have some valve cover gaskets I need to change soon. I can make one when I do the job.
You don't have to take the springs off the electrical conectors
Loved the video!!!!! About to get this done on large Marge real soon!🧰🛠️
For someone who is not mechanically inclined, it coud have been better. You have to explain every little thing that you do. You take some kind of a metal piece to rub the wire? I couldn't tell if you were saying run or rub. And I wish I knew exactly how much dialectic grease to put in and where. Were you saying boot? What is a boot?
ouu shite after this video I cant wait till the morning to replace my spark plugs. Replacing them always make your car feel like a new machine. My buick was pretty much revived after replacing a few snapped ignition wires and plugs. (surprise it even started i was running on 4 cylinders.) Im excited for this lil repair cause my hyundai really does need it. Got the car for 500$ and its a fixer upper but its a great car
awesome job! THANKS
I followed your video and now my acceleration is acting crazy and my rpm is at 1100 in idle and when I drive it’s going all over the place could I have messed with the throttle cable?
Just did this yesterday, put it all together and the throttle linkage is all crazy. Revved all the way up and I had to pull back on the pedal to get it to rev down again. Trying to figure out how to adjust haha
Very helpful video.
Hey God bless you.i want to know are this car are good and easy to fix.i really got my eye on one 2005 Hyundai Sonata please let me know
This one is still on the road today. It's easy to work on and reliable. Currently at 259k miles and it took me to work today.
Hello, I cannot get the rear bolts (even one) started. I see it line up, but I won't start. Maybe the position of plenum?(angle) Any suggestions?
Do you have to replace the wires too? Or could you just get away with just changing the plugs?
You can just do the plugs, but given the amount of work it takes to get to them, you are best off doing the whole job at the same time. It would suck to have to repeat all your work because a wire went bad. If it's an easy spark plug job, like a 4 cylinder, i am more likely to skip the wires.
Very well done.
Thank you!!
Excellent video thank you
How long did this take you?
so, what's the firing order?
Nice video. I wanted to ask if you've tried pushing in the wire clips on the electrical plugs instead of removing them? My BMW wire connectors have a similar wire clip and they just push in and then pull the connector right off. I learned this after several lost clips as they are under tension. Good luck!
Cool video. Thanks!!!
I started to take off the wires on the front plugs and can not get them off! I used a wire grip tool and still could not get off. I was afraid to pull too hard or they come apart?
Suggestion? Car has 128k on plugs...
Twisting and pulling is your key to success. The wires should be changed since it's such a in depth job anyway so if you mess a spark cable up it's no big deal but twist and pull at same time back and forth it'll eventually come
How about iridium plugs instead of platinum? The dealer recommended them.
Robert Thompson always use iridium imho. They last about 3-4 times longer and can handle way more than the delta would ever need.
Wow man that looks like a bitch! You got a lot of patience to deal with that without cursing or throwing shit. My hats off too ya on that one!
Awesome!
The plugs come with anti seize now.
hyundai tucson 2.7 v6 sparks recomending ?
What is the name of the vacuum hose at 8:49 this hose is disconnected and broke at the tip where it goes at the intake manifold. The car is misfiring could this be the reason?
Curious what the torque specs are ?
I'm having trouble with the bolt on the right side under the throttle body.
I did not hear any mention of what the plug gap size should be or are they preset ? I'm working on a 2004 2.7 Sante Fe
Hyundai recomends 43, So you can gap anywhere from 42-46, as its not an exact science. Im doing mine right now and gapped mine at 44.
@@ExcessInModeration Thanks was a big help I set them at .042 and works well :)