Sorry for the late answer! Here the adress from MAX FRANK UK. There you can order all components for our sealing systems and can get more technical advice: Max Frank Ltd. Clough Street, Hanley Stoke-on-Trent, ST1 4AF, Staffordshire UKUnited Kingdom +44 (0)1782 598 041 info@maxfrank.co.uk
Hector! Sorry for the late replay! Please write a letter to: mf-customer.service@maxfrank.com within your country adress. Our costumer service will get in contact with you and will find your m´nearest dealer.
Yes, there is a possibility to position the injection access directly on a crack. To do this, make sure that the packer is really positioned in the crack (at the end) to ensure that the resin goes into the crack. In addition, it is suggested that the crack be closed between the packers to create enough pressure to fill the entire crack. This is not the usual way because it is very difficult to make sure that the crack is hit at the end of the packer - you cannot see into the concrete. Therefore, drilling into the crack is usually done from the side - this guarantees that the crack is kept in place. For purchase in Canada, please contact our colleagues: Max Frank Inc. Canada 49 Maplecrest Lane Brantford, Ontario N3R 7T9 Tel +1 519 759 3854 info@maxfrank.ca
Dear costumer! Please write a letter to: mf-customer.service@maxfrank.com within your country adress. Our costumer service will get in contact with you and will find your m´nearest dealer.
Hello! The price depends on your requirement. If you tell me in which area you live I can give you the contact of our sales person or dealer. You can find more information at www.maxfrank.com
Hi Hector! It is a little bit depending on when you use what raisin: If you have already a leak with running water you use "Intectin® Blitz" this stops the water and is more like "foam". After that, you use "Intectin® PUR or Intectin® EP to fill the crack to have it repaired. Think about Intec as the only house that could be used several times. For any further questions give us a call!
The rubber part functions as a seal in order to be able to build up and maintain appropriate injection pressure. There is no resin flowing out from the rubber gasket only at the packer end.
Dear Jonson A you can tighten the injection ports (packer) with a power drill adapter as well. However, injection ports are sensitive to over torque, and the power drill adapter should be used be experienced workers only. Best regards Max Frank Group
Injection equipment and hardware can be purchased through Max Frank. Please inquire with Sealing Technology Product Management, Att.: Mr. Nils Grüske-Weißenbach, MSc.
Either the crack is leaking, then the location is self-evident. In general, you will inject cracks that are wider than the crack width that will self-heal through lime leaching. Typical rang for maximum design crack width is 0,15 to 0,4 mm. Therefore, all cracks that require injection will be readily visible.
Sorry, but MAX FRANK products are not available online. Please contact our customer service: www.maxfrank.com/intl-en/contact/?navid=901539901539 Thanks for your interest.
Excellent demo and I strongly recommended to learn this technique by every civil engineer
Dear K. Padmanablam! Very happy to hear that. Many thanks for that recomondation
excellent video...the best and easy to follow step-by-step process...
Julio. We are very happy to hear! If you need more info to the product feel free to contact our Canadian sales: www.maxfrank.com/ca-en/contact/
Very good.
We need a complete information about acrylic gel injection which is better than polyurthane foam.
nice explanation...good discription
Thank you!
Super video,where can I fint this pomp?
मेरो लागी उपयुक्त बिधि।
❤
Great information
I'm working on this in japan
Thanks for that! If you need further information just call us via e-mail on the Webpage: www.maxfrank.com
Where can I but one of them injection guns? based in the UK
Sorry for the late answer! Here the adress from MAX FRANK UK. There you can order all components for our sealing systems and can get more technical advice:
Max Frank Ltd.
Clough Street, Hanley
Stoke-on-Trent, ST1 4AF, Staffordshire
UKUnited Kingdom
+44 (0)1782 598 041
info@maxfrank.co.uk
Where can you get packers and this pump ?
Hector! Sorry for the late replay! Please write a letter to: mf-customer.service@maxfrank.com within your country adress. Our costumer service will get in contact with you and will find your m´nearest dealer.
Hi , how we can get in kenya country please
Is there any situation where the packers are installed into the crack itself?
Where can I purchase in Ontario, Canada?
Yes, there is a possibility to position the injection access directly on a crack.
To do this, make sure that the packer is really positioned in the crack (at the end) to ensure that the resin goes into the crack.
In addition, it is suggested that the crack be closed between the packers to create enough pressure to fill the entire crack.
This is not the usual way because it is very difficult to make sure that the crack is hit at the end of the packer - you cannot see into the concrete.
Therefore, drilling into the crack is usually done from the side - this guarantees that the crack is kept in place.
For purchase in Canada, please contact our colleagues:
Max Frank Inc. Canada
49 Maplecrest Lane
Brantford, Ontario N3R 7T9
Tel +1 519 759 3854
info@maxfrank.ca
Is drillling 45 degrees from the side reccomended for the concrete slab thickness less than 1/2 inch (12.5 cm)?
wow, incredible
How can I get this material at Lahore Pakistan.
good epoxy injection process
How thick is the dope?
Ok
but my one question when injection and material not available in area then what will do .?please any other material are suggest me .
In which area do you live? Maybe we or one of our dealers can support you.
Where do I get this apparratuses
Dear costumer! Please write a letter to: mf-customer.service@maxfrank.com within your country adress. Our costumer service will get in contact with you and will find your m´nearest dealer.
excellent explanation
Thank you!
how much price of this kit?
Hello! The price depends on your requirement. If you tell me in which area you live I can give you the contact of our sales person or dealer. You can find more information at www.maxfrank.com
Is it foam or sealant ? Does it expand ?
Hi Hector! It is a little bit depending on when you use what raisin:
If you have already a leak with running water you use "Intectin® Blitz" this stops the water and is more like "foam". After that, you use "Intectin® PUR or Intectin® EP to fill the crack to have it repaired. Think about Intec as the only house that could be used several times.
For any further questions give us a call!
The steel packer is going through the crack. Does the black (Expandable) part of the packer has the ability to diffuse the resin?
The rubber part functions as a seal in order to be able to build up and maintain appropriate injection pressure. There is no resin flowing out from the rubber gasket only at the packer end.
What is price????
Please contact our customer service:
www.maxfrank.com/intl-en/contact/?navid=901539901539
Thanks for your interest.
What is the warranty after procedure had been done? Can this kit be purchased in Canada and where?
Please enquire with our Canadian branch:
Max Frank (Canada) Inc.49 Maplecrest Lane Brantford, Ontario N3R 7T9Canada
Phone: +1 519 759 3854
Fax: +1 519 759 3854
toll free: 1-888-244-4668
E-mail: info@maxfrank.ca
Web: www.maxfrank.ca
Why working spins Injection port manually key? Included screwdriver tool has not enough money to head for the screwdriver?
Dear Jonson A
you can tighten the injection ports (packer) with a power drill adapter as well. However, injection ports are sensitive to over torque, and the power drill adapter should be used be experienced workers only.
Best regards
Max Frank Group
I install and do injection for 100-200 packers per day. Sometimes more.
This is not possible using such a pump and spinning each packer manually.
Hi Igor - an interesting aspect! What type of connection between hose and packer you would use to make the coupling faster?
@@MAXFRANKGroupI use a compressed air-operated high-pressure piston pump for injection.
To tighten packers - impact driver/wrench + socket.
how to buy the pump injection
Injection equipment and hardware can be purchased through Max Frank. Please inquire with Sealing Technology Product Management, Att.: Mr. Nils Grüske-Weißenbach, MSc.
do you have a website of email contact for the injection pumps ?
so thats how the professionals do it :P
How do you know the location of the cracks?
Either the crack is leaking, then the location is self-evident. In general, you will inject cracks that are wider than the crack width that will self-heal through lime leaching. Typical rang for maximum design crack width is 0,15 to 0,4 mm. Therefore, all cracks that require injection will be readily visible.
I would never do this, just replace the concrete. Are we going to college for this complicated step lol my my my
Hii
i want to buy the complete accesories . is it on sale online.
Sorry, but MAX FRANK products are not available online.
Please contact our customer service:
www.maxfrank.com/intl-en/contact/?navid=901539901539
Thanks for your interest.