You choose to listen and then complain ? These videos are extremely helpful and very well presented and they are FREE. I say thanks a million times for these videos and the way they are done. God bless
Thank you Mark! This has got to be the most thorough video on the EVAP system I have seen to date. I have been looking all over the internet for the last month trying to figure out why my codes keep coming back. I now know much more than I ever knew before, thanks to this video. I have copied down that list of 14 codes that I am sure will come in handy in the future. I have replaced the vent solenoid on the canister, gas cap and just purchased the purge solenoid bolted to the air filter Should get here next week. 2 Garages have yet to come up with what the root cause is. I even had them do a smoke test to check for leaks and they found none. I am keeping my fingers crossed on the purge valve. Codes are P0440, P0441, P0442, P0446. 2002 Toyota Sienna LE. Barry
Thank you for the kind words. It sounds like you have a tough problem. Hang in there, there is always an answer. Below is the test procedure for the codes you have on your vehicle. The most probable causes are : cracked - loose hoses, canister, fuel cap, canister closed valve and vacuum switching valve ... in this order. 1. Verify the gas cap is a factory Toyota gas cap. 2. Locate the Canister Closed Valve (CCV), on or by the air filter housing, and verify the hose is connected and not loose. 3. Test the CCV, the Purge Solenoid (PS) and the Vacuum Switching Valve (VSV) on the charcoal canister, by manually grounding them and verify they operate and function properly. Some scan tools will activate the solenoids also, so it is a good thing to activate them through a scan tool so one knows the wire harness and the Engine Control Module (ECM) is OK. The CCV is normally open and it should close and hold vacuum when grounded. The VSV on the canister is normally closed, and when grounded, should open. The PS should open when grounded and apply vacuum to the charcoal canister for purge control and evaporative system testing. 4. Next, simulate an evaporative test and verify the system holds a vacuum and functions normally. To do that test, get to the ECM and backprobe the signal wire for the pressure sensor. It should read around 3.3 volts, no vacuum or pressure. Next, ground the CCV and the VSV on the canister. Start the vehicle, and if there is manifold vacuum to the PS, manually tap it to ground and draw a vacuum in the evaporative system and the fuel tank, then verify the pressure sensor voltage drops to around 2 volts. Then stop grounding the PS and see if the system leaks. If a smoke machine is used, the canister will leak, so clamp off the hose, that commonly has the Yellow stripe, to test the system. 5. Always ground the CCV and the VSV solenoid, on the canister, 20 to 30 times and verify they still operate when hot. Stay in touch, Mark Hicks Wells Vehicle Electronics
You are very welcome. Knowing you enjoyed and learned from our production makes all the effort worth it! Take Care, Mark Hicks Wells Vehicle Electronics
Mark,I put the charcoal can and vent valve on my sentra.Found it used on ebay.Did the trick.You saved me a ton of money.You're a genius.Thanks a million.
Thanks for doing the impossible: making an evap emissions systems video entertaining. An evap video with 559K views(6/23/2019)proves it. The voice-over actor must have been happy to use his acting skills.
When conventional educational tech videos are shown to a class of tired technicians it's easy for them to fall asleep. Not so with the Sgt .Tech video,it will keep them awake.
Hello Dalukebark, It is pretty common for the purge valve to stick open on your vehicle and cause a P0441 code to set. Remove the purge valve and first check to see if it is stuck open. If it is closed apply power and ground (9volt battery works well, polarity does not matter) to the valve and blow through it to see if it is opening all the way. You may need to do this several times. Either way it is probably your problem. Keep in touch, Mark
Man i gotta tell you Mark, these are some of the best insructional and easy to understand automotive related videos. I'm gonna be taking the Engine Performance(A8) and HVAC (A7) ASEs in November, and these videos you have are helping me tremendously. . Really appreciate it!!
wow thanks for the post. I have been doing this work for years and this is the best explanation of the way the system operates. Makes it a lot easier to troubleshoot when you know how it works and what it looks for to set the light.
A P0440 can be a tough diagnostics. If you seal the system and apply pressure or vacuum, depending upon the system, you can watch the voltage change on the pressure sensor. I am happy to hear you were able to correct your problem.
Trying to work thru an EVAP issue on my truck . Wish I would have found this video first as it explains everything you need to know . One problem was the video was so entertaining it had me chuckling a bit due to the DI character's lines . Well done !
@Kasilindo 3. Functional test would be to supply power and ground to the valve, it should fully open and close when ground is removed. Would recommend testing multiple times in case it sticks intermittently and look for evidence of moisture that could cause it to hang up in cold weather. 4. Check the feed line to the purge valve, one should be able to draw freely through it and get the smell of fuel. Inspect the under side for damaged lines
3. On this system Toyota is using a leak detection module on the charcoal canister and the module includes a pressure sensor and a canister vent valve and a vacuum pump. The pressure sensor will monitor if the purge solenoid under the hood is working correctly and then monitor the system for a leak when the ECM grounds the canister vent valve and then the pump will pump vacuum into the system to check for leaks.
Wow. This makes more sense of other videos on evap system. I totally misunderstood the purpose of the vent valve before watching this video..Awesome job .
Thank you for the kind words. Your feelings about the video are exactly how we wanted it to come across. The P0452 on your vehicle is many times caused by a broken Dark Green signal wire. Usually it breaks either by the master cylinder or under the drivers seat carpeting. Check the Dark Green wire for an open or short to ground from the sensor back to the Powertrain Control Module (PCM). Goes to Blue connector pin 39. Hope this helps, Mark Hicks Wells Vehicle Electronics
You are absolutely correct! I have a Tech 2 and Snap on verus and they will both function the purge and vent solenoids on GMs. The verus is capable of doing this on most vehicles. Excellent input, Thank you, Mark Hicks Wells Vehicle Electronics
The purge solenoid is the gate to allow fumes stored in the canister to flow into the intake and then the combustion chamber. This typically happens when the engine is cruising and the vacuum is somewhere around 10 inches. If it was connected to the air intake it would pull much harder and the possibility of drawing raw fuel would be much greater. Hope this helps, Mark Hicks Wells Vehicle Electronics
1. Check for any vacuum leaks, even at the brake booster. This system will have an irratic idle if there is a vacuum leak. 2. Using a scan tool, check to see what the desired idle and what the actual is, normally these values are close to each other. 3. Block off the Idle Air Control (IAC) passage to see if that stabilizes the RPM. 4. Use a lab scope or Digital Volt meter to monitor the TPS voltage. If the voltage is erratic, check the sensor ground, if OK, replace the TPS. Keep in Touch, Mark
Sometimes a good visual inspection can find a leak, but, you are right the only way to be sure is to have it smoked. If the problem is a sticky purge or vent solenoid they can be detected by activating the solenoid. Mark Hicks Wells Vehicle Electronics
Markjhicks: thank you for your answer. as I mentionned, I changed the charcoal canister but this did not fix the problem for the code p0441. According to the video means that NO FLOW DURING PURGE CYCLE. So the problem is between the charcoal canister and the engine. I think there is only one part which is under the hood, is the VSV: Vaccum Switch Valve. You said you should check the VSV and Vent solenoid. I am gonna change the VSV then I will see if it will fix the problem. Thanks again for your information. We came to learn and share our experience in order to help each others.
tanumi e hey! I know this is a 5 year old thread, and I haven’t been through all the comments yet but I am getting the same pO441 code on my 2001 B5 Audi. Did you figure out what the part was that was the curse of your p0441 code? I don’t open and just changing parts and crossing my fingers, luckily I am getting no adverse effects from this code other then the ‘check engine light’ with is annoying but not enuf too spend money I shouldn’t on EVAP parts! Any reply would be appreciate! Especially after 5 years!!! 😀 God Bless
1. Activate the EVAP system vent and purge solenoids. 2. Check for the EVAP system to hold vacuum with either a gauge on the service port or by monitoring the Fuel Tank Pressure Sensor (FTPS) voltage. 3. Deactivate the EVAP purge solenoid, vacuum should hold and FTPS voltage should be higher than 1.5 volts. The most common causes in order of probability for your vehicle are: Fuel Cap Vent solenoid Purge solenoid Evap system hose Filler neck (rust hole) Mark Hicks Wells Vehicle Electronics
You are correct andimillard. When the emissions testing station does a plug - in test, they are looking for monitors that are set or not. When you clear the codes the ready-ness monitors are also reset. Mark Hicks Wells Vehicle Electronics
wow i remember watching an old school video (probably made in the 40/50s lol) on how the brake system works. set-up is like a "mechanic military training video." its black and white but very informative. i understand it more than reading my automotive books. this video is also similar to it. this is a great video for us all. thank you sir! i also had a P0452 DTC on my 2003 pontiac sunfire and i dont have any idea about the evap system. now i have a better understanding how to fix that DTC .
2. Check the purge flow switch on the firewall. Verify that the Black wire has a good ground and the Brown wire has approximately 5 volts with no purge flow and goes to ground when vacuum is applied to the purge flow switch when the purge system is operating while driving. 3. If the purge solenoid and purge flow switch test OK, check the vacuum "T" in the circuit. The vacuum "T" has orifices built inside it. If an incorrect part was installed, the purge flow code can set.
Yeah, I was leaning towards this as it is a common fix on my car. Thanks for replying back. If I figure it out I will post back with what it was and how I pinpointed it. Thanks again.
@4man321 This usually means the vent solenoid is sticking. Because it is not sticking all the time, it makes it very hard to find the leak. If you want to throw a dart at it, I would suggest trying the vent solenoid. If you want to test it. Try smoking it and energizing the solenoid with jumper leads and either a 9 or 12 volt battery. Do repetitive taps on the connector to try to get it to stick. Mark Hicks Wells Vehicle Electronics
The canister purge solenoid and purge solenoid are the same part. Turn the key to "on" and check which of the two terminals are getting hot going to the purge solenoid. Then with the key still "on" ground and engine running, ground the other terminal and check for vacuum to the canister. If this does not occur replace the solenoid. Mark Hicks Wells Vehicle Electronics
Well this is a good question. The best way is to use a smoke machine. The only other way is to do a very close visual inspection and try blowing through EVAP hoses, be careful not to inhale! The only other choice is to start guessing. i can help you with that. I will need the code to get started. Mark Hicks Wells Vehicle Electronics
Hello Chris, A P0442 is not very common for your vehicle, however there are a couple failures you might want to check first before you have the system smoke tested. Check the fuel cap, some of the retail stores can do that for like AutoZone. Then access the Canister Vent (CANV) solenoid on the carbon canister. Turn the key on and ground the Gray/Yellow (GY/Y) wire and check to verify that the solenoid is mechanically closed, by attempting to blow through it. Next response...
@markjhicks To test the purge solenoid, verify there is battery voltage at the Black/Yellow wire and when the Yellow/Blue wire is ground the purge solenoids should open and vacuum should be applied to the charcoal canister. 3. Next verify the canister closed valve closes tight and seals off the canister. The canister closed valve is located on the canister and when the White/Red wire is grounded the valve should close and the canister should hold vacuum.
@markjhicks If the canister closed valve does not close and hold vacuum, then it will need to be replaced. 4. Check all the EVAP lines and hoses for leaks and check for a cracked or leaking canister. Also verify the fuel cap is tight and not missing and the seal is good. I hope this helps, if you have any further questions let me know! Mark Hicks Wells Vehicle Electronics
There should be no gas leaking from the canister. This usually means the purge solenoid is stuck, the engine is badly flooded or running very rich. I am assuming you have a 5.3 engine. It is common for the fuel compensation sensor to cause this issue too. Stay in touch, Mark Hicks Wells Vehicle Electronics
The most common cause by far for a P0442 on your vehicle is hoses leaking. Check the system hoses very carefully. The ones under the hood and by the canister are most suspect-able. A leaking fuel cap is also fairly common. Let me know wither way please, Mark Hicks Wells Vehicle Electronics
A scan tool with the correct software will be needed to operate the leak detection pump and vent shut valve. Always verify the pressure sensor has a good 5 volts and a good ground and the signal wire read around 3.3 volts no vacuum or pressure in the system. The leak detection module uses a 0.2 in orifice and pumps vacuum through the orifice and checks for the calibrated reading on the pressure sensor.
2. Check to verify that there is voltage to the solenoids, key on. If there is voltage to both solenoids, the second wire is the wire the Engine Control Module (ECM) will ground to control the solenoid. On the CVS valve, backprobe the Green/White (GRN/WHT) wire, ground it and verify that the valve will close and hold vacuum. Also verify that it will open when the ground is taken away.
The other most common causes for a P0455 on an 04 Monte Carlo is the vent solenoid and vacuum hoses. If you do not have a scan tool, you can test the vent solenoid integrity by activating it with a 9 volt battery and applying vacuum with a hand pump. It should hold vacuum when activated. This may have to be performed several times to find the intermittent problem. Hope this helps, please let me know the results of your testing. Mark
@GabeJH82 The other line at the NVLD goes to the vent. Block the vent line.Using a hand vacuum pump, apply vacuum to the line while watching the voltage on the Violet/White wire. Voltage is supposed to change at approximately 1" Hg vacuum. Try testing this switch several times to see if the switch is sticking. Replace the NVLD if the switch is sticking. It is very common for the NVLD to fail on your vehicle. I hope this helps you, Mark Hicks Wells Vehicle Electronics
@h8ncars Most common cause for the P0441 on your vehicle is a defective canister purge solenoid. here is the check: 1. At the canister purge solenoid check to see if there is battery voltage to the Yellow/Black wire any time the key is on. ground the Red wire and check to see if the solenoid passes vacuum through to the canister assembly. 2. Check the canister for being saturated. Hope this helps, stay in touch, Mark Hicks Wells Vehicle Electronics
Great point! You are right if there is air by passing the MAF it will affect the fuel mixture and cause idle problems! Thank you for your comment bujashaka it is right on! Mark Hicks Wells Vehicle Electronics
1. Connect a Digital Volt Ohmmeter (DVOM) to the Orange wire at the Natural Vacuum Leak Detection (NVLD) assembly. Keep the NVLD connected. 2. Start the engine and voltage should be at least 10 volts. 3. Remove the vent hose from the NVLD assembly and check if vacuum is present from the port on the NVLD. If not, let the engine run longer until it starts purging and vacuum is felt on the port.
@sharkzf6 Thank you for the kind words. An EVAP monitor can happen only at specific times, this maybe the reason you are not getting any codes. Nonetheless, you need to have the canister, vent and purge solenoids checked. The solenoids are known to be intermittent. Stay with it, don't let it get out of warranty. Mark
I am always here to help! We were all new at this at one time. Please don't confuse what i said, EVAP canister purge solenoid, EVAP purge solenoid and the EVAP purge control solenoid are all the same part. Manufactures will at times call things different names but they are the same part. An EVAPorative will also have a vent solenoid. Usually these are the two EVAP solenoids the vehicle will have. The purge solenoid is on top of the engine and the vent solenoid is back by the tank usually.
I would start checking the vacuum hoses from the canister to the front, this is the most common cause. The only way to really test this system is to smoke it. If you do not have a smoke machine and you are sure the hoses look good, the next most common cause is the purge solenoid and then the Leak Detection Pump. If you need more assistance let me know, Mark Hicks Wells Vehicle Electronics
I have to agree, as long as it is not in an emission testing area. The fuel economy you will save will not justify the cost of the repair. Mark Hicks Wells Vehicle Electronics
Rickyorton, On a 99 Toyota Corolla it is very common for the Vacuum Switching Valve to have connection problems. I will assume at this point you do not have a scan tool that can read PIDS. If you do let me know and I will give you specific test instructions. Otherwise, test and verify that the purge solenoid and wire harness are all OK. The purge solenoid should apply vacuum to the charcoal canister when grounded.
Without knowing what vehicle you have, my first thought is a vent solenoid sticking issue. This is common on Domestic vehicles. On Asian vehicles it is also common for the vacuum switching valve to stick. Mark Hicks Wells Vehicle Electronics
Unfortunately, it is common on your vehicle for the charcoal canister to let go. Meaning the charcoal pellets are stuck everywhere in the system. Try disconnecting the vacuum hoses to the canister and look for the pellets. Also look at the fuel tank fill vent valve. It is on top of the tank but you can get to the hoses from the bottom. You will need to clean all the hoses, lines and check valves. Also replace the canister and possibly the diagnosis module for tank leakage (DMTL). Mark
Then the ECM closes the vent valve and tests the fuel tank and gas cap and evaporative system for a leak. Always verify the vent line for this system is not restricted. I hope this helps you. The most common fix is the updated ECM. Mark Hicks Wells Vehicle Electronics
Usually the problem is associated with the purge solenoid. Verify that the purge valve vacuum hoses are connected correctly (purge valve is near the ignition coils). If all looks good it is time to take a chance and replace the purge solenoid. To test it further you will need a scan tool and possibly a smoke machine. Hope this helps, Mark Hicks Wells Vehicle Electronics
It is very common for the canister purge solenoid to be bad on your vehicle. 1. Locate the purge solenoid by the cruise control servo, verify that it is not stuck open. Also ground the solenoid, raise the engine RPM and verify that vacuum is applied to the charcoal canister. If the purge solenoid is faulty, replace the solenoid.
@markjhicks The voltage should be 2.46 - 2.56 volts. If the voltage is incorrect and the connection is good, then the fuel tank pressure sensor is faulty. 2. Verify the purge solenoid operates and if the scan tool shows purge operation the solenoid should be operating applying vacuum to the charcoal canister.
Also verify that the hose from the purge solenoid to the charcoal canister does not leak. IF this all looks good and you are looking for the most common cause...it is time to replace the charcoal canister. Please keep me informed with the results. Mark Hicks
@AutoTechHector Well Hector I am not sure what to say, other than this is the best compliment you can give me. I hope you do well with the test, please stay in touch and let everyone know how well you do. Mark Hicks Wells Manufacturing L.P.
P0452 has to do with the fuel tank pressure sensor. It is not common on your vehicle. First check the connections to the PCM and the pressure sensor. Clean them with electronics cleaner. Stay in touch, Mark Hicks Wells Vehicle Electronics
Thank you for the kind words, they mean a lot to us! We wanted a fun way to approach what can be a dull presentation. Kind of like taking medicine with a little bit of sugar. Take Care, Mark Hicks Wells Vehicle Electronics
P0440 is an EVAP code, it should not be an issue to drive it for another day. It is very common for the fuel filler cap to leak on your vehicle and cause this code. You might to try one and maybe save a few bucks. After putting the cap on you will need to clear the codes. If the light comes back on, get it checked out. Mark Hicks Wells Vehicle Electronics
Check the EVAP purge solenoid on rear of intake plenum with vacuum gauge. You will find it has a small continuous suction even when not engaged. Chances are you will need to replace the solenoid. Mark
All I can do is advise the common failures. Most common is a leaking fuel cap, next is Canister vent solenoid. To be sure you will need to smoke the system, to find the leak. Best of luck if you have any further questions let me know. Mark Hicks Wells Vehicle Electronics
@javien108 A P0442 concerns a leak in the EVAP system which will typically have no drive-ability issues. The most common causes for this code on your vehicle are: fuel cap, filler neck, purge or vent solenoid and canister leaks. I suggest having the system smoked to help with the diagnostics. Mark Hicks Wells Manufacturing L.P.
Typically no, but on some rare occasions yes depending upon the type of vehicle. What kind of problems are you having? What is the year, make, model and engine size? Is the check engine light "on"? Are there any codes stored in the computer? I am happy to help you the best I can. Mark
@1pigman 1. Disconnect the Fuel Tank Pressure (FTP) sensor and check for 5 volts on the Gray wire and ground on the Black/White wire. 2. Jump the Gray wire to the Dark Green wire and see if the scanner shows 5 volts. 3. Check the Dark Green wire for an open or short to ground from the sensor back to the Powertrain Control Module (PCM). Goes to the Red connector pin 25. If you just want to guess, replace the fuel tank pressure sensor and connector. Mark Hicks Wells Manufacturing L.P.
dippinsix4, it is common on your vehicle for either evaporative emission vent or purge solenoid to fail. The puge solenoid is located near the throttle body and the vent is near the fuel tank. It sounds like the failure is extremely intermittent, so it might be tough to pin it down. You can energize both solenoids with a 9 volt battery, jumping to the two pins on the solenoids. You might have to do this a number of times to find the one that is not clicking. I hope this helps ...
@DonMecanico Thank you for the kind words. Here is a challenge. If you think you know something, try to teach to everyone in a way all will understand. Thank you again, your comment really meant a lot to me. Mark Hicks Wells Vehicle Electronics
@Kasilindo No, this code will not make the engine stop running. Check for spark and fuel first, let me know what you find and I will help you. Testing code P0441 BMW 1. Access the purge valve, attached to the lower front part of the intake manifold, near the mass airflow sensor. 2. It has two wires going to it, the Red/White/Yellow wire has 12 volts key on, and the Brown wire is ground for the control circuit.
Wowww... That was really a cool video and the learning really sticks with you! We as techs need more like this. Funny but gives real world learning that a tech can appreciate!!!! I subscribed!!! 🛠️🛠️🛠️🛠️🛠️👍
The first thing you want to do is get the code, it will help lead us in the right direction. But just a guess ... either the EVAP vent solenoid is stuck closed or you have a restricted or kinked vent hose. Mark Hicks Wells Vehicle Electronics
1. Locate the Canister Vent Shut (CVS) valve on the side of the charcoal canister, and the bypass solenoid under the cover next to the canister. Both solenoids have a Black/Yellow (BLK/YEL) wire that supplies voltage to the them.
Hey Private are you calling me a FAKE! Get down and give me twenty! :) To be fair it will be a while before we do another Sgt. Tech video. But yes this is the place. Mark Hicks Wells Vehicle Electronics
1. Test the system as outlined on TSB #02-02-S001. If no scan tool is available, will have to manually control the canister cut valve by grounding the Brown/White wire and then manually ground the purge solenoid by grounding the Red/Blue wire. 2. During testing, if the fuel tank pressure sensor does not indicate a vacuum, continue to ground the purge solenoid with the engine running and canister cut valve still closed.
You may have to clear the codes to get the light to go out. You will then have to reset all the monitors before you go for an emissions test. The canister is on the left hand front of the engine compartment under the PCM. Mark Hicks Wells Vehicle Electronics
By far the most common cause for the P0455 on your vehicle is a defective Evaporative Emissions (EVAP) Canister Vent Solenoid/Valve. Without testing nothing is for sure, but this is a good guess. Let me know what happens. Mark Hicks Wells Vehicle Electronics
4. While watching the DVOM, plug the port and check if the voltage goes to 0 volts. The vacuum relief valve in the NVLD may make noise when doing this as it should release excessive vacuum. 5. If the voltage does not drop to 0 volts when the port is blocked, the NVLD assembly is bad. A defective NVLD is by far the most probable cause. Mark Hicks Wells Vehicle Electronics
It is possible if the purge solenoid is stuck open and pulling raw fuel from the tank flooding the engine. Pull the hoses and see if there is any raw fuel in them. Mark Hicks Wells Vehicle Electronics
Follow Toyota TSB # EG041-07 for issues Toyota is having with the purge solenoid. There is an updated ECM for these codes. If the ECM has been updated, then verify the purge solenoid under the hood operates correctly and supplies vacuum to the canister and shuts off when the solenoid is not being commanded by the ECM.
Most common repair Activated Charcoal Filter Shutoff Valve Y58 or gas cap. but the gas cap can not cause the leak. The only testing available is with the factory scan tool. Stay in Touch Mark Hicks Wells Vehicle Electronics
George is right! however without knowing the year, make, model and engine size there are all kinds of problems and could be's we could state. This is a very common problem with GM vehicles also. Typically it is the vent solenoid which causes it. Mark Hicks Wells Vehicle Electronics
@vinman1029 It is common to find a leak at the canister vent solenoid where it mounts to the charcoal canister. In this case it is usually best to replace the vent solenoid and the canister. Please let me know what happens, Mark Hicks Wells Manufacturing
An EVAP code will not interfere with the engine starting. Does the engine crank? If it cranks have you checked it for spark and fuel? easy way to check for a lack of fuel is to spray a little starting fluid into the throttle body and see if it fires. Let me know, Mark Hicks Wells Vehicle Electronics
You choose to listen and then complain ? These videos are extremely helpful and very well presented and they are FREE. I say thanks a million times for these videos and the way they are done. God bless
World full of Karens. Just gotta piss on everything good. Must be a sad existence 😂
Thank you Mark!
This has got to be the most thorough video on the EVAP system I have seen to date. I have been looking all over the internet for the last month trying to figure out why my codes keep coming back.
I now know much more than I ever knew before, thanks to this video.
I have copied down that list of 14 codes that I am sure will come in handy in the future.
I have replaced the vent solenoid on the canister, gas cap and just purchased the purge solenoid bolted to the air filter
Should get here next week.
2 Garages have yet to come up with what the root cause is. I even had them do a smoke test to check for leaks and they found none.
I am keeping my fingers crossed on the purge valve.
Codes are P0440, P0441, P0442, P0446.
2002 Toyota Sienna LE.
Barry
Thank you for the kind words. It sounds like you have a tough problem. Hang in there, there is always an answer. Below is the test procedure for the codes you have on your vehicle. The most probable causes are : cracked - loose hoses, canister, fuel cap, canister closed valve and vacuum switching valve ... in this order.
1. Verify the gas cap is a factory Toyota gas cap.
2. Locate the Canister Closed Valve (CCV), on or by the air filter housing, and verify the hose is connected and not loose.
3. Test the CCV, the Purge Solenoid (PS) and the Vacuum Switching Valve (VSV) on the charcoal canister, by manually grounding them and verify they operate and function properly. Some scan tools will activate the solenoids also, so it is a good thing to activate them through a scan tool so one knows the wire harness and the Engine Control Module (ECM) is OK. The CCV is normally open and it should close and hold vacuum when grounded. The VSV on the canister is normally closed, and when grounded, should open. The PS should open when grounded and apply vacuum to the charcoal canister for purge control and evaporative system testing.
4. Next, simulate an evaporative test and verify the system holds a vacuum and functions normally. To do that test, get to the ECM and backprobe the signal wire for the pressure sensor. It should read around 3.3 volts, no vacuum or pressure. Next, ground the CCV and the VSV on the canister. Start the vehicle, and if there is manifold vacuum to the PS, manually tap it to ground and draw a vacuum in the evaporative system and the fuel tank, then verify the pressure sensor voltage drops to around 2 volts. Then stop grounding the PS and see if the system leaks. If a smoke machine is used, the canister will leak, so clamp off the hose, that commonly has the Yellow stripe, to test the system.
5. Always ground the CCV and the VSV solenoid, on the canister, 20 to 30 times and verify they still operate when hot.
Stay in touch,
Mark Hicks
Wells Vehicle Electronics
Pipecorn i know you posted this 7yrs ago I but what was your final root cause? I’m chasing down this issue now myself on my 2011
Thanks so much for posting this. This is the best explanation about the EVAP system that I have ever heard. It cleared up a lot of things for me.
You are very welcome. Knowing you enjoyed and learned from our production makes all the effort worth it!
Take Care,
Mark Hicks
Wells Vehicle Electronics
Mark,I put the charcoal can and vent valve on my sentra.Found it used on ebay.Did the trick.You saved me a ton of money.You're a genius.Thanks a million.
Thanks for doing the impossible: making an evap emissions systems video entertaining. An evap video with 559K views(6/23/2019)proves it.
The voice-over actor must have been happy to use his acting skills.
Hahaha thanks for watching Joe!
Mike Becker, Senior Technical Instructor
When conventional educational tech videos are shown to a class of tired technicians it's easy for them to fall asleep. Not so with the Sgt .Tech video,it will keep them awake.
Haha glad it'll keep them awake.
Mike Becker, Senior Technical Instructor
Didn't know a EVAP video could be somewhat entertaining to watch. Now going to fix my P0442 issue. Thanx!
Haha who knew? Thanks for watching Jeff!
Mike Becker, Senior Instructor
Hello Dalukebark,
It is pretty common for the purge valve to stick open on your vehicle and cause a P0441 code to set. Remove the purge valve and first check to see if it is stuck open. If it is closed apply power and ground (9volt battery works well, polarity does not matter) to the valve and blow through it to see if it is opening all the way. You may need to do this several times. Either way it is probably your problem.
Keep in touch,
Mark
Thank you for following up with the results. It was my pleasure.
Take Care,
Mark Hicks
Man i gotta tell you Mark, these are some of the best insructional and easy to understand automotive related videos. I'm gonna be taking the Engine Performance(A8) and HVAC (A7) ASEs in November, and these videos you have are helping me tremendously. . Really appreciate it!!
wow thanks for the post. I have been doing this work for years and this is the best explanation of the way the system operates. Makes it a lot easier to troubleshoot when you know how it works and what it looks for to set the light.
You are welcome. If i can help you further, just let me know.
Mark Hicks
Wells Vehicle Electronics
A P0440 can be a tough diagnostics. If you seal the system and apply pressure or vacuum, depending upon the system, you can watch the voltage change on the pressure sensor. I am happy to hear you were able to correct your problem.
Trying to work thru an EVAP issue on my truck . Wish I would have found this video first as it explains everything you need to know . One problem was the video was so entertaining it had me chuckling a bit due to the DI character's lines . Well done !
Thanks for watching!
~Ryan Wilsing
@Kasilindo
3. Functional test would be to supply power and ground to the valve, it should fully open and close when ground is removed. Would recommend testing multiple times in case it sticks intermittently and look for evidence of moisture that could cause it to hang up in cold weather.
4. Check the feed line to the purge valve, one should be able to draw freely through it and get the smell of fuel. Inspect the under side for damaged lines
3. On this system Toyota is using a leak detection module on the charcoal canister and the module includes a pressure sensor and a canister vent valve and a vacuum pump. The pressure sensor will monitor if the purge solenoid under the hood is working correctly and then monitor the system for a leak when the ECM grounds the canister vent valve and then the pump will pump vacuum into the system to check for leaks.
Wow. This makes more sense of other videos on evap system. I totally misunderstood the purpose of the vent valve before watching this video..Awesome job .
Thank you for the kind words. Your feelings about the video are exactly how we wanted it to come across.
The P0452 on your vehicle is many times caused by a broken Dark Green signal wire. Usually it breaks either by the master cylinder or under the drivers seat carpeting. Check the Dark Green wire for an open or short to ground from the sensor back to the Powertrain Control Module (PCM). Goes to Blue connector pin 39.
Hope this helps,
Mark Hicks
Wells Vehicle Electronics
You are absolutely correct! I have a Tech 2 and Snap on verus and they will both function the purge and vent solenoids on GMs. The verus is capable of doing this on most vehicles. Excellent input, Thank you,
Mark Hicks
Wells Vehicle Electronics
The purge solenoid is the gate to allow fumes stored in the canister to flow into the intake and then the combustion chamber. This typically happens when the engine is cruising and the vacuum is somewhere around 10 inches. If it was connected to the air intake it would pull much harder and the possibility of drawing raw fuel would be much greater.
Hope this helps,
Mark Hicks
Wells Vehicle Electronics
1. Check for any vacuum leaks, even at the brake booster. This system will have an irratic idle if there is a vacuum leak.
2. Using a scan tool, check to see what the desired idle and what the actual is, normally these values are close to each other.
3. Block off the Idle Air Control (IAC) passage to see if that stabilizes the RPM.
4. Use a lab scope or Digital Volt meter to monitor the TPS voltage. If the voltage is erratic, check the sensor ground, if OK, replace the TPS.
Keep in Touch, Mark
Sometimes a good visual inspection can find a leak, but, you are right the only way to be sure is to have it smoked. If the problem is a sticky purge or vent solenoid they can be detected by activating the solenoid.
Mark Hicks
Wells Vehicle Electronics
Markjhicks: thank you for your answer. as I mentionned, I changed the charcoal canister but this did not fix the problem for the code p0441. According to the video means that NO FLOW DURING PURGE CYCLE. So the problem is between the charcoal canister and the engine. I think there is only one part which is under the hood, is the VSV: Vaccum Switch Valve. You said you should check the VSV and Vent solenoid. I am gonna change the VSV then I will see if it will fix the problem.
Thanks again for your information.
We came to learn and share our experience in order to help each others.
Perfect! I love that!
Mark Hicks
Wells Vehicle Electronics
tanumi e hey! I know this is a 5 year old thread, and I haven’t been through all the comments yet but I am getting the same pO441 code on my 2001 B5 Audi. Did you figure out what the part was that was the curse of your p0441 code? I don’t open and just changing parts and crossing my fingers, luckily I am getting no adverse effects from this code other then the ‘check engine light’ with is annoying but not enuf too spend money I shouldn’t on EVAP parts!
Any reply would be appreciate! Especially after 5 years!!! 😀
God Bless
1. Activate the EVAP system vent and purge solenoids.
2. Check for the EVAP system to hold vacuum with either a gauge on the service port or by monitoring the Fuel Tank Pressure Sensor (FTPS) voltage.
3. Deactivate the EVAP purge solenoid, vacuum should hold and FTPS voltage should be higher than 1.5 volts.
The most common causes in order of probability for your vehicle are:
Fuel Cap
Vent solenoid
Purge solenoid
Evap system hose
Filler neck (rust hole)
Mark Hicks
Wells Vehicle Electronics
You are correct andimillard. When the emissions testing station does a plug - in test, they are looking for monitors that are set or not. When you clear the codes the ready-ness monitors are also reset.
Mark Hicks
Wells Vehicle Electronics
Thank you for the kind words, they mean a lot to us!!
Mark Hicks
Wells Vehicle Electronics
wow i remember watching an old school video (probably made in the 40/50s lol) on how the brake system works. set-up is like a "mechanic military training video." its black and white but very informative. i understand it more than reading my automotive books. this video is also similar to it. this is a great video for us all. thank you sir! i also had a P0452 DTC on my 2003 pontiac sunfire and i dont have any idea about the evap system. now i have a better understanding how to fix that DTC .
2. Check the purge flow switch on the firewall. Verify that the Black wire has a good ground and the Brown wire has approximately 5 volts with no purge flow and goes to ground when vacuum is applied to the purge flow switch when the purge system is operating while driving.
3. If the purge solenoid and purge flow switch test OK, check the vacuum "T" in the circuit. The vacuum "T" has orifices built inside it. If an incorrect part was installed, the purge flow code can set.
Yeah, I was leaning towards this as it is a common fix on my car. Thanks for replying back. If I figure it out I will post back with what it was and how I pinpointed it. Thanks again.
@4man321 This usually means the vent solenoid is sticking. Because it is not sticking all the time, it makes it very hard to find the leak. If you want to throw a dart at it, I would suggest trying the vent solenoid. If you want to test it. Try smoking it and energizing the solenoid with jumper leads and either a 9 or 12 volt battery. Do repetitive taps on the connector to try to get it to stick.
Mark Hicks
Wells Vehicle Electronics
Thank you for the kind words. We are grateful you took the time to leave such a great comment.
Mark Hicks
Wells Vehicle Electronics
The canister purge solenoid and purge solenoid are the same part. Turn the key to "on" and check which of the two terminals are getting hot going to the purge solenoid. Then with the key still "on" ground and engine running, ground the other terminal and check for vacuum to the canister. If this does not occur replace the solenoid.
Mark Hicks
Wells Vehicle Electronics
Well this is a good question. The best way is to use a smoke machine. The only other way is to do a very close visual inspection and try blowing through EVAP hoses, be careful not to inhale! The only other choice is to start guessing. i can help you with that. I will need the code to get started.
Mark Hicks
Wells Vehicle Electronics
Hello Chris,
A P0442 is not very common for your vehicle, however there are a couple failures you might want to check first before you have the system smoke tested. Check the fuel cap, some of the retail stores can do that for like AutoZone.
Then access the Canister Vent (CANV) solenoid on the carbon canister. Turn the key on and ground the Gray/Yellow (GY/Y) wire and check to verify that the solenoid is mechanically closed, by attempting to blow through it.
Next response...
@markjhicks To test the purge solenoid, verify there is battery voltage at the Black/Yellow wire and when the Yellow/Blue wire is ground the purge solenoids should open and vacuum should be applied to the charcoal canister.
3. Next verify the canister closed valve closes tight and seals off the canister. The canister closed valve is located on the canister and when the White/Red wire is grounded the valve should close and the canister should hold vacuum.
@markjhicks If the canister closed valve does not close and hold vacuum, then it will need to be replaced.
4. Check all the EVAP lines and hoses for leaks and check for a cracked or leaking canister. Also verify the fuel cap is tight and not missing and the seal is good.
I hope this helps, if you have any further questions let me know!
Mark Hicks
Wells Vehicle Electronics
There should be no gas leaking from the canister. This usually means the purge solenoid is stuck, the engine is badly flooded or running very rich. I am assuming you have a 5.3 engine. It is common for the fuel compensation sensor to cause this issue too.
Stay in touch,
Mark Hicks
Wells Vehicle Electronics
The most common cause by far for a P0442 on your vehicle is hoses leaking. Check the system hoses very carefully. The ones under the hood and by the canister are most suspect-able. A leaking fuel cap is also fairly common. Let me know wither way please,
Mark Hicks
Wells Vehicle Electronics
Excellent presentation. A great reinforcement for those recent seminars. And why do ppl complain about Srge Tech?
Hey, its old animations and stuff. The info is good, the presentation is....old. Thanks for watching!
Mike Becker, Technical Services Instructor
A scan tool with the correct software will be needed to operate the leak detection pump and vent shut valve. Always verify the pressure sensor has a good 5 volts and a good ground and the signal wire read around 3.3 volts no vacuum or pressure in the system.
The leak detection module uses a 0.2 in orifice and pumps vacuum through the orifice and checks for the calibrated reading on the pressure sensor.
2. Check to verify that there is voltage to the solenoids, key on. If there is voltage to both solenoids, the second wire is the wire the Engine Control Module (ECM) will ground to control the solenoid. On the CVS valve, backprobe the Green/White (GRN/WHT) wire, ground it and verify that the valve will close and hold vacuum. Also verify that it will open when the ground is taken away.
The other most common causes for a P0455 on an 04 Monte Carlo is the vent solenoid and vacuum hoses. If you do not have a scan tool, you can test the vent solenoid integrity by activating it with a 9 volt battery and applying vacuum with a hand pump. It should hold vacuum when activated. This may have to be performed several times to find the intermittent problem. Hope this helps, please let me know the results of your testing.
Mark
@GabeJH82 The other line at the NVLD goes to the vent. Block the vent line.Using a hand vacuum pump, apply vacuum to the line while watching the voltage on the Violet/White wire. Voltage is supposed to change at approximately 1" Hg vacuum. Try testing this switch several times to see if the switch is sticking. Replace the NVLD if the switch is sticking. It is very common for the NVLD to fail on your vehicle.
I hope this helps you,
Mark Hicks
Wells Vehicle Electronics
@carlosderek Thank you for the kind words. In fact we have another EVAP video coming out soon.
Mark Hicks
Wells Vehicle Electronics
@DonMecanico Best comment all week! It was a lot of fun to make too. Thanks for the kinds words!
Take care,
Mark Hicks
Wells Vehicle Electronics
Thank you your kind words mean a lot to us!
Mark Hicks
Wells Vehicle Electronics
@h8ncars Most common cause for the P0441 on your vehicle is a defective canister purge solenoid. here is the check: 1. At the canister purge solenoid check to see if there is battery voltage to the Yellow/Black wire any time the key is on. ground the Red wire and check to see if the solenoid passes vacuum through to the canister assembly.
2. Check the canister for being saturated.
Hope this helps, stay in touch,
Mark Hicks
Wells Vehicle Electronics
Great point! You are right if there is air by passing the MAF it will affect the fuel mixture and cause idle problems!
Thank you for your comment bujashaka it is right on!
Mark Hicks
Wells Vehicle Electronics
1. Connect a Digital Volt Ohmmeter (DVOM) to the Orange wire at the Natural Vacuum Leak Detection (NVLD) assembly. Keep the NVLD connected.
2. Start the engine and voltage should be at least 10 volts.
3. Remove the vent hose from the NVLD assembly and check if vacuum is present from the port on the NVLD. If not, let the engine run longer until it starts purging and vacuum is felt on the port.
@sharkzf6 Thank you for the kind words. An EVAP monitor can happen only at specific times, this maybe the reason you are not getting any codes. Nonetheless, you need to have the canister, vent and purge solenoids checked. The solenoids are known to be intermittent. Stay with it, don't let it get out of warranty.
Mark
I am always here to help! We were all new at this at one time.
Please don't confuse what i said, EVAP canister purge solenoid, EVAP purge solenoid and the EVAP purge control solenoid are all the same part. Manufactures will at times call things different names but they are the same part. An EVAPorative will also have a vent solenoid. Usually these are the two EVAP solenoids the vehicle will have. The purge solenoid is on top of the engine and the vent solenoid is back by the tank usually.
@benjiego22 Thank you for the kind words. Glad you enjoyed the video.
Mark Hicks
Wells Vehicle Electronics
I would start checking the vacuum hoses from the canister to the front, this is the most common cause. The only way to really test this system is to smoke it. If you do not have a smoke machine and you are sure the hoses look good, the next most common cause is the purge solenoid and then the Leak Detection Pump.
If you need more assistance let me know,
Mark Hicks
Wells Vehicle Electronics
I have to agree, as long as it is not in an emission testing area. The fuel economy you will save will not justify the cost of the repair.
Mark Hicks
Wells Vehicle Electronics
Rickyorton,
On a 99 Toyota Corolla it is very common for the Vacuum Switching Valve to have connection problems. I will assume at this point you do not have a scan tool that can read PIDS. If you do let me know and I will give you specific test instructions. Otherwise, test and verify that the purge solenoid and wire harness are all OK. The purge solenoid should apply vacuum to the charcoal canister when grounded.
I wish they kept sgt. tech around , awesome..
Without knowing what vehicle you have, my first thought is a vent solenoid sticking issue. This is common on Domestic vehicles. On Asian vehicles it is also common for the vacuum switching valve to stick.
Mark Hicks
Wells Vehicle Electronics
Unfortunately, it is common on your vehicle for the charcoal canister to let go. Meaning the charcoal pellets are stuck everywhere in the system. Try disconnecting the vacuum hoses to the canister and look for the pellets. Also look at the fuel tank fill vent valve. It is on top of the tank but you can get to the hoses from the bottom. You will need to clean all the hoses, lines and check valves. Also replace the canister and possibly the diagnosis module for tank leakage (DMTL).
Mark
Then the ECM closes the vent valve and tests the fuel tank and gas cap and evaporative system for a leak. Always verify the vent line for this system is not restricted.
I hope this helps you. The most common fix is the updated ECM.
Mark Hicks
Wells Vehicle Electronics
Usually the problem is associated with the purge solenoid.
Verify that the purge valve vacuum hoses are connected correctly (purge valve is near the ignition coils). If all looks good it is time to take a chance and replace the purge solenoid. To test it further you will need a scan tool and possibly a smoke machine.
Hope this helps,
Mark Hicks
Wells Vehicle Electronics
It is very common for the canister purge solenoid to be bad on your vehicle.
1. Locate the purge solenoid by the cruise control servo, verify that it is not stuck open. Also ground the solenoid, raise the engine RPM and verify that vacuum is applied to the charcoal canister. If the purge solenoid is faulty, replace the solenoid.
@markjhicks The voltage should be 2.46 - 2.56 volts. If the voltage is incorrect and the connection is good, then the fuel tank pressure sensor is faulty.
2. Verify the purge solenoid operates and if the scan tool shows purge operation the solenoid should be operating applying vacuum to the charcoal canister.
Also verify that the hose from the purge solenoid to the charcoal canister does not leak. IF this all looks good and you are looking for the most common cause...it is time to replace the charcoal canister. Please keep me informed with the results.
Mark Hicks
Thank you for the kind words! Now Carry on ...
Sgt. Tech
Wells Vehicle Electronics
@AutoTechHector Well Hector I am not sure what to say, other than this is the best compliment you can give me. I hope you do well with the test, please stay in touch and let everyone know how well you do.
Mark Hicks
Wells Manufacturing L.P.
P0452 has to do with the fuel tank pressure sensor. It is not common on your vehicle. First check the connections to the PCM and the pressure sensor. Clean them with electronics cleaner.
Stay in touch,
Mark Hicks
Wells Vehicle Electronics
Thank you for the kind words, they mean a lot to us!
We wanted a fun way to approach what can be a dull presentation. Kind of like taking medicine with a little bit of sugar.
Take Care,
Mark Hicks
Wells Vehicle Electronics
It was a miscue in the video, in this system the vent solenoid is normally open, you are correct.
P0440 is an EVAP code, it should not be an issue to drive it for another day. It is very common for the fuel filler cap to leak on your vehicle and cause this code. You might to try one and maybe save a few bucks. After putting the cap on you will need to clear the codes. If the light comes back on, get it checked out.
Mark Hicks
Wells Vehicle Electronics
Check the EVAP purge solenoid on rear of intake plenum with vacuum gauge. You will find it has a small continuous suction even when not engaged. Chances are you will need to replace the solenoid.
Mark
All I can do is advise the common failures. Most common is a leaking fuel cap, next is Canister vent solenoid. To be sure you will need to smoke the system, to find the leak. Best of luck if you have any further questions let me know.
Mark Hicks
Wells Vehicle Electronics
Excellent, our goal was to have fun and teach in terms most everyone can understand.
Take Care
Mark Hicks
Wells Vehicle Electronics
@javien108 A P0442 concerns a leak in the EVAP system which will typically have no drive-ability issues. The most common causes for this code on your vehicle are: fuel cap, filler neck, purge or vent solenoid and canister leaks. I suggest having the system smoked to help with the diagnostics.
Mark Hicks
Wells Manufacturing L.P.
Typically no, but on some rare occasions yes depending upon the type of vehicle.
What kind of problems are you having? What is the year, make, model and engine size? Is the check engine light "on"? Are there any codes stored in the computer?
I am happy to help you the best I can.
Mark
@1pigman 1. Disconnect the Fuel Tank Pressure (FTP) sensor and check for 5 volts on the Gray wire and ground on the Black/White wire.
2. Jump the Gray wire to the Dark Green wire and see if the scanner shows 5 volts.
3. Check the Dark Green wire for an open or short to ground from the sensor back to the Powertrain Control Module (PCM). Goes to the Red connector pin 25.
If you just want to guess, replace the fuel tank pressure sensor and connector.
Mark Hicks
Wells Manufacturing L.P.
dippinsix4,
it is common on your vehicle for either evaporative emission vent or purge solenoid to fail. The puge solenoid is located near the throttle body and the vent is near the fuel tank. It sounds like the failure is extremely intermittent, so it might be tough to pin it down. You can energize both solenoids with a 9 volt battery, jumping to the two pins on the solenoids. You might have to do this a number of times to find the one that is not clicking. I hope this helps ...
@DonMecanico Thank you for the kind words. Here is a challenge. If you think you know something, try to teach to everyone in a way all will understand. Thank you again, your comment really meant a lot to me.
Mark Hicks
Wells Vehicle Electronics
At 1:09 I liked the choice of a WW2 Jeep to as an example of an older HC vapor emitting vehicle.
@Kasilindo No, this code will not make the engine stop running. Check for spark and fuel first, let me know what you find and I will help you.
Testing code P0441 BMW
1. Access the purge valve, attached to the lower front part of the intake manifold, near the mass airflow sensor.
2. It has two wires going to it, the Red/White/Yellow wire has 12 volts key on, and the Brown wire is ground for the control circuit.
Wowww... That was really a cool video and the learning really sticks with you! We as techs need more like this. Funny but gives real world learning that a tech can appreciate!!!! I subscribed!!! 🛠️🛠️🛠️🛠️🛠️👍
The first thing you want to do is get the code, it will help lead us in the right direction. But just a guess ... either the EVAP vent solenoid is stuck closed or you have a restricted or kinked vent hose.
Mark Hicks
Wells Vehicle Electronics
1. Locate the Canister Vent Shut (CVS) valve on the side of the charcoal canister, and the bypass solenoid under the cover next to the canister. Both solenoids have a Black/Yellow (BLK/YEL) wire that supplies voltage to the them.
Very informative video. I don't mind your presentation style, it is much better than a computer generated voice like in some other videos out there.
Hey Private are you calling me a FAKE! Get down and give me twenty! :)
To be fair it will be a while before we do another Sgt. Tech video. But yes this is the place.
Mark Hicks
Wells Vehicle Electronics
Thank you for the update and great comment, we truly appreciate it!
Mark Hicks
Wells Vehicle Electronics
Thank you for the kind words ... now get back to work private! :)
Mark Hicks
Wells Vehicle Electronics
1. Test the system as outlined on TSB #02-02-S001. If no scan tool is available, will have to manually control the canister cut valve by grounding the Brown/White wire and then manually ground the purge solenoid by grounding the Red/Blue wire.
2. During testing, if the fuel tank pressure sensor does not indicate a vacuum, continue to ground the purge solenoid with the engine running and canister cut valve still closed.
Great video focusing on an often hard to understand and diagnose system!
You may have to clear the codes to get the light to go out. You will then have to reset all the monitors before you go for an emissions test. The canister is on the left hand front of the engine compartment under the PCM.
Mark Hicks
Wells Vehicle Electronics
By far the most common cause for the P0455 on your vehicle is a defective Evaporative Emissions (EVAP) Canister Vent Solenoid/Valve. Without testing nothing is for sure, but this is a good guess. Let me know what happens.
Mark Hicks
Wells Vehicle Electronics
It works and is wired on the principle of a strain gauge similar to a MAP sensor.
Most scan tools allow running the EVAP monitor, the fuel tank pressure sensor can be tested at that time.
I would check with smoke wizard. You can find them on the AES wave site.
Mark Hicks
Wells Vehicle Electronics
Vent solenoid is normally open to ventilate during temperature changes and tank re-filling.
4. While watching the DVOM, plug the port and check if the voltage goes to 0 volts. The vacuum relief valve in the NVLD may make noise when doing this as it should release excessive vacuum.
5. If the voltage does not drop to 0 volts when the port is blocked, the NVLD assembly is bad.
A defective NVLD is by far the most probable cause.
Mark Hicks
Wells Vehicle Electronics
It is possible if the purge solenoid is stuck open and pulling raw fuel from the tank flooding the engine. Pull the hoses and see if there is any raw fuel in them.
Mark Hicks
Wells Vehicle Electronics
Follow Toyota TSB # EG041-07 for issues Toyota is having with the purge solenoid. There is an updated ECM for these codes.
If the ECM has been updated, then verify the purge solenoid under the hood operates correctly and supplies vacuum to the canister and shuts off when the solenoid is not being commanded by the ECM.
Most common repair Activated Charcoal Filter Shutoff Valve Y58 or gas cap. but the gas cap can not cause the leak.
The only testing available is with the factory scan tool.
Stay in Touch
Mark Hicks
Wells Vehicle Electronics
George is right! however without knowing the year, make, model and engine size there are all kinds of problems and could be's we could state. This is a very common problem with GM vehicles also. Typically it is the vent solenoid which causes it.
Mark Hicks
Wells Vehicle Electronics
@vinman1029 It is common to find a leak at the canister vent solenoid where it mounts to the charcoal canister. In this case it is usually best to replace the vent solenoid and the canister. Please let me know what happens,
Mark Hicks
Wells Manufacturing
An EVAP code will not interfere with the engine starting. Does the engine crank? If it cranks have you checked it for spark and fuel? easy way to check for a lack of fuel is to spray a little starting fluid into the throttle body and see if it fires.
Let me know,
Mark Hicks
Wells Vehicle Electronics