Have the hover 1 different version slightly. 1st ride 16.7 on GPS. Decided to watch your video pulled the wire easy AF. 2nd run 19.3 with less battery power. Nice info...
I find when I drive my car stoned I end up doing 60klm down the motorway I have to set cruise control to keep me at a constant 100klm otherwise my foot relaxes and I slow down
Sorry guys but this “hack” has no effect on speed. I have done back to back testing on the road as well as controlled bench testing using an optical tachometer. The white wire does not effect speed at all. The battery voltage level will effect speed - also proven with an optical tachometer. With 42v the no-load speed of the system is 21.33 mph (with or without white wire connected). Once the battery drops to 41v the no load speed drops to a 20.5 mph. This shows that the firmware is not limiting speed but rather the voltage is. Also, speed is reported to the system by the phase wires - proven by the fact that the speedo still reports when the white wire is disconnected.
I disagree. There is an actual limiter on Hover 1 scooters. Going downhill on my Hover 1-x it throttles back when it reaches 20.5 MPH. Hence, watching this vid. Cheers
The white wire it's the temperature sensor, not a speed limiter. It does help to prevent the scooter to shut off by it's own when using sport mode and going over a bump. I have 11of these scoorters for rentals.
Hey man. As someone who owns 11 of these, I was hoping you could give me some advice. I got an extended warranty when I bought it and that turned out to be a good idea. I’m getting a cash payout and keeping the dead scooter but I want to see if I can bring it back to life if I can. Idk if it’s moisture or what but I imagine it is. What do you do when a customer brings a scooter back dead and what do you find the issue usually is? It may be a busted battery but I just don’t want to spend money on a new pack if thats not the issue and replacing it does nothing.
can you expand a little bit on whats going on when it shuts off over a bump? It seems there are 2 conditions where it will shut off. 1) when I'm on flat terrain but its summer and i've been riding a while and the wheel is super hot and this makes sense 2) if i go over a bump, especially crossing railroads. it seems as if something shorted or maybe the harness jiggled or such. I'd love any experiences you can share
@@Jackbarrany I took my dead batteries that were brand new than been sitting on the shelf for years when I put a multimeter on them they showed one volt in the whole battery. I took the wrapping off of the battery on top of my battery there is a long circuit board on each end of that circuit board there is a b+ and a b minus. All you do is take a small 20 volt battery with a 2ah and hook it up to the good battery on the b+ hook it up to the b+ on the bad battery and the b minus on the bad battery and hold it there for a couple minutes and then check the voltage with a meter tester. It should start taking a charge do that for about 20 minutes until you get the battery up to about 20 volts and then put your charger on it. It works.
If removing the speed limiter doesn't work, swap out the stock lithium battery with a more powerful lithium battery. I'm guessing go with either a 60 volt or 72 volt battery. Also. You may need to replace the stock controller with a different controller rated up to 500 watts or 1000 watts. This will rest assuredly, definitely increase the speed because the motor is now operating off whatever controller is being used. This is the prime key to increasing speed. Key fact: Controllers control the operation of the motor and increasing the voltage will increase power. Be very mindful not to use too much wattage and voltage because you will burn out the motor.
Interesting, maybe you can help me out, i have a 2000w 48v, 20Ah lithium, scooter, limited to 45 km/h(EU norm) , first what max speed could i reach when unlocked, i didnt find out where the limiter could be, maybe in the controler itself?and or do i need to replace the motor and control unit? or iss 2000w to less to go over 45 km/h? but i dont think so, i saw videos from scooters with 2000w who reach 65 km/h..
@@Biostatic the limiter varies. In some cases, its a thin white wire. In other cases, the speed limit is programmed into the software. Who knows. But I know what you mean. My advice is to try and move up to 3000 Watts and 72 volts...............or even 5000 Watts.. 3000 Watts and 72 volts is pretty powerful. That's what I have on my own e-bike. I just blow by other e-bikers and even the larger scooters that need license plates. But I see ehat your saying. You probably want to modify the system you have already to cut costs. Try running the 2000 Watts off 60 volts
@@milestone_achiever4634 thx for your advice🤘, i think its its programmed into the software, and there is no way(atleast for me) to re-programm it, go for 5000 watts would be cool, but there's to less space for replacement, but maybe 3000 watts could be an option, since i can legit drive on the streets with my 2000 watts 48v, i thought it would be easy to go for more speed, but im thinkin youre right, changing battery plus controller would make more sense...
It’ll do 20 mph out of the box as measured by gps, but the Speedo on the scooter says 15 mph. What the white wire does idk., I’ve tried it both connected and disconnected, no difference. Whoever told you the white wire keeps it from going 20 is full of it; my guess is it may have something to do with over heat protection.
I think all you did was disable the recharge circuit from coasting. That's really silly because like you said you get no extra speed. Instead you only hurt your battery time. I have two of these scooters and absolutely love them. As stock downhill already exceeds 15 mph although the speedo won't tell you so. The wind definitely will.
I own an e-bike and e-scooter and both I have removed the restrictor I have D8 Pro e Scooter with 10.4ah battery and I have fixed a seat to it my e-bike I put together my self and has 15ah battery and a 500w rear hub so e-bike can do up to 40mph now and my e-scooter goes up to 20mph but i normally only go around 20mph tops on my e-bike see I didn't really want to go silly speeds I just needed more torque now I get that extra push to get up hills so if you're just looking for a bit more torque then this can help with that also. This info can be very helpful, so Reginald Sharma has earned him self a new subscriber and a LIKE on his video!
Dont take out the limiter,they were put there for a purpose,to maintain stability concerning speen and to not overheat the motor.The faster you go is the more voltage sent to the motor
With my experience on my hover 1 alpha, I can get passed the top speed by turning off and on the scooter while it’s moving. I have no idea why this effects the speed though it leads me to believe that it has something to do with the software.
This doesn't really make it any faster... It lets the motor still run while you're going downhill, so you can go SLIGHTLY faster downhill. And it makes it to where your motor doesn't cut out when it "overheats". Which tbh, is super useful. But it doesn't make it go any faster.
Maybe using a 5/64" SAE Allen wrench instead of a 2mm metric Allen wrench for a hex screw on something built in somewhere other than the USA did the stripping?
U should put some type of Silicone to seal it good because I noticed the actual seal is ruined Once u take out the screws. And that’s very important since Water 💦 gravel dirt ect r flying through.
The white wire does not limit the speed. I attempted this mod with no change in speed. Now I'm going to mod the controller add jumpers to bypass the on board resistors/fuse limiting the power output.
@@BwadeReacts Installed. There are so many to choose from. I'll update my description. It's simple and shows what matters: MPH, Max MPH and Distance Traveled.
hello shawn my name is Efrain. and my question is I have a hover 1. and it wont start. I plug in the power supply, and all the lights goes on but it wont start.. can you help me with this problem. I really appreciate it
hey sharma. its efrain again. my scooter is used. but in excellent condition. I still have the same problem. only when I plug in the charger, all everything lights up, yet no motion. it stays lit and after 2 or 3 minutes, the scooter automaticaly shuts down. @@ReginaldSharma
Sounds to be like an electrical or motor issue. I would return it if possible. If it's was like this when you got it then it's a dud. Get that money back!
@ReginaldSharma Hey Mr. Sharma. Is there a possibility that the controller, which is under the stand where you control the start and power to make the scooter go. There are many unlabled connections cables, some are named AYT g6, e5 and most are brown and black. Does the power, not the one which goes into the controller but the other one. Help
Hi. I'm really not sure. I personally would return it if there is any electrical issues because now you will be spending time and money trying to diagnose it. Could be controller but I can't be sure. Only way to know is replace it and see.
How about the limit of rpm of the motor Is it fine to overclock your controller Without relying the right amount of watts for the motor? Cannot cause for a an overheating it?
Update it does not have any effect on your battery I get to and from from work everyday at 23 miles per hour I've been doing it for the last 4 weeks there isn't any notable change in my battery power
Hey bro when you remove the limiter it blows the motor out within a month or 2 after wards plzz be careful when doing this.. the wheel locks up when the motor blows out and hopefully your not going fast when this happens believe me I had 5 scooters already LOL
Hi Reginald, did you ever do the battery upgrade for this one? I have a journey and even though warranty its only a year, I figured once it expires ill swap the battery since ive done a few already.
I wanted to badly but then kept getting distracted by other things and never got to it. I even have all the things to make it happen … laziness happened haha
gray wire not white wire and if gray i'll just put in series of volume control so I can Adjust the speed limit not disconnected all the way as the motor will heat up and goes without limit .
@@bighorse215 Is that bad? I mean, I don't want my scooter to just randomly shut off on me while I'm mid-riding. But I also don't want to do damage to my battery or motor?
@@waleedabdulrab8779 honestly if everything is stock you can't really do much damage because there are still power cut out built into the battery and controller. Plus your battery will drain before you ever ride long enough to fry the electronics.
Can someone PLEASE tell me how to fix a cracked throttle button on a hover 1 journey. My daughter pressed it really hard, and now the speed works sometimes, and when it does it’s not full speed
speedyescooterrepairshop.com/ visit us and ask any repair questions. We will answer any and all questions pertaining to electric scooter/bike issues. Like us @ facebook.com/speedyescooterrepair
Deanna Vilaseca-Lopez is it the pioneer? Make sure it is inflated to 50fps and also tighten the bolts holding the wheel on (you need to remove the reflectors and the screws underneath first and then pop the black caps off)
Thanks for the shout-out. Everyone that does this please make sure you adjust breaks to make them be able to stop at 20mph
I posted your video to the xiaomi m365 Facebook groups and ebike group. You will get hundreds of views real quick
Thanks man. Appreciate the help! It's thanks to you that I found how to do this so credit is all you :)
Thank him after a few weeks your controller will burn or the motors life will diminish and fry
@@PURGE-3000 did that happen to you??
Bryan Wick to a lot of clients buddy.
Have the hover 1 different version slightly. 1st ride 16.7 on GPS. Decided to watch your video pulled the wire easy AF. 2nd run 19.3 with less battery power. Nice info...
you took a 30 seconds of info and stretched it out to 5 and a half.
Best way to go faster is drive at night stoned the speedo wont say so but it flies.
So so true.. 😂 sometimes I feel like I’m just riding along and not actually even in control of the scoot 🤣
Lol
I’ve never had this phenomenon lol but I fall of more when it’s night so I can see ur point 😂😂😂
Real niggas felt this
I find when I drive my car stoned I end up doing 60klm down the motorway I have to set cruise control to keep me at a constant 100klm otherwise my foot relaxes and I slow down
Sorry guys but this “hack” has no effect on speed.
I have done back to back testing on the road as well as controlled bench testing using an optical tachometer. The white wire does not effect speed at all.
The battery voltage level will effect speed - also proven with an optical tachometer.
With 42v the no-load speed of the system is 21.33 mph (with or without white wire connected). Once the battery drops to 41v the no load speed drops to a 20.5 mph.
This shows that the firmware is not limiting speed but rather the voltage is.
Also, speed is reported to the system by the phase wires - proven by the fact that the speedo still reports when the white wire is disconnected.
I disagree. There is an actual limiter on Hover 1 scooters. Going downhill on my Hover 1-x it throttles back when it reaches 20.5 MPH. Hence, watching this vid. Cheers
@@arslanahmed8504I also disagree I have dual 700w motors paired with a 36v battery which should at least get me 25-30 mph.
The white wire it's the temperature sensor, not a speed limiter. It does help to prevent the scooter to shut off by it's own when using sport mode and going over a bump. I have 11of these scoorters for rentals.
Hey man. As someone who owns 11 of these, I was hoping you could give me some advice. I got an extended warranty when I bought it and that turned out to be a good idea. I’m getting a cash payout and keeping the dead scooter but I want to see if I can bring it back to life if I can. Idk if it’s moisture or what but I imagine it is. What do you do when a customer brings a scooter back dead and what do you find the issue usually is? It may be a busted battery but I just don’t want to spend money on a new pack if thats not the issue and replacing it does nothing.
can you expand a little bit on whats going on when it shuts off over a bump? It seems there are 2 conditions where it will shut off. 1) when I'm on flat terrain but its summer and i've been riding a while and the wheel is super hot and this makes sense 2) if i go over a bump, especially crossing railroads. it seems as if something shorted or maybe the harness jiggled or such. I'd love any experiences you can share
@@Jackbarrany I took my dead batteries that were brand new than been sitting on the shelf for years when I put a multimeter on them they showed one volt in the whole battery. I took the wrapping off of the battery on top of my battery there is a long circuit board on each end of that circuit board there is a b+ and a b minus. All you do is take a small 20 volt battery with a 2ah and hook it up to the good battery on the b+ hook it up to the b+ on the bad battery and the b minus on the bad battery and hold it there for a couple minutes and then check the voltage with a meter tester. It should start taking a charge do that for about 20 minutes until you get the battery up to about 20 volts and then put your charger on it. It works.
Oh wow my ADHD wasnt affected and 5.5 min. was rather detailed enough forgot to skip thru. I can tell this was one of those spontaneous vids...
If removing the speed limiter doesn't work, swap out the stock lithium battery with a more powerful lithium battery. I'm guessing go with either a 60 volt or 72 volt battery.
Also. You may need to replace the stock controller with a different controller rated up to 500 watts or 1000 watts. This will rest assuredly, definitely increase the speed because the motor is now operating off whatever controller is being used. This is the prime key to increasing speed.
Key fact: Controllers control the operation of the motor and increasing the voltage will increase power.
Be very mindful not to use too much wattage and voltage because you will burn out the motor.
Interesting, maybe you can help me out, i have a 2000w 48v, 20Ah lithium, scooter, limited to 45 km/h(EU norm) , first what max speed could i reach when unlocked, i didnt find out where the limiter could be, maybe in the controler itself?and or do i need to replace the motor and control unit? or iss 2000w to less to go over 45 km/h? but i dont think so, i saw videos from scooters with 2000w who reach 65 km/h..
@@Biostatic the limiter varies. In some cases, its a thin white wire. In other cases, the speed limit is programmed into the software. Who knows. But I know what you mean. My advice is to try and move up to 3000 Watts and 72 volts...............or even 5000 Watts..
3000 Watts and 72 volts is pretty powerful. That's what I have on my own e-bike. I just blow by other e-bikers and even the larger scooters that need license plates.
But I see ehat your saying. You probably want to modify the system you have already to cut costs.
Try running the 2000 Watts off 60 volts
@@milestone_achiever4634 thx for your advice🤘, i think its its programmed into the software, and there is no way(atleast for me) to re-programm it, go for 5000 watts would be cool, but there's to less space for replacement, but maybe 3000 watts could be an option, since i can legit drive on the streets with my 2000 watts 48v, i thought it would be easy to go for more speed, but im thinkin youre right, changing battery plus controller would make more sense...
It’ll do 20 mph out of the box as measured by gps, but the Speedo on the scooter says 15 mph. What the white wire does idk., I’ve tried it both connected and disconnected, no difference. Whoever told you the white wire keeps it from going 20 is full of it; my guess is it may have something to do with over heat protection.
I think all you did was disable the recharge circuit from coasting. That's really silly because like you said you get no extra speed. Instead you only hurt your battery time. I have two of these scooters and absolutely love them. As stock downhill already exceeds 15 mph although the speedo won't tell you so. The wind definitely will.
Your judging speed by... Wind? 😂 😂 😂
You are very funny
These scooters were made only to run at a certain temperature
Would have been nice to show us the difference in speed
I own an e-bike and e-scooter and both I have removed the restrictor I have D8 Pro e Scooter with 10.4ah battery and I have fixed a seat to it my e-bike I put together my self and has 15ah battery and a 500w rear hub so e-bike can do up to 40mph now and my e-scooter goes up to 20mph but i normally only go around 20mph tops on my e-bike see I didn't really want to go silly speeds I just needed more torque now I get that extra push to get up hills so if you're just looking for a bit more torque then this can help with that also. This info can be very helpful, so Reginald Sharma has earned him self a new subscriber and a LIKE on his video!
TY 🙂 btw which e-bike do you have? I want to try my hand at building one myself.
@@ReginaldSharma 26" Rear Wheel Electric Bicycle Conversion Kit E-bike Hub Motor Set For V-shaped 500w (
@@GodFartherOG Ty!!
You're a legend bro, i appreciate the work you did appreciate 🙏
Can u upload a video of it going faster than 15
Did you do a battery pack upgrade? And where do I get it?
Dont take out the limiter,they were put there for a purpose,to maintain stability concerning speen and to not overheat the motor.The faster you go is the more voltage sent to the motor
So What are you trying to say? It sets the thing on fire?
@@citi360 Its harmful to motor
We want speed!!
@@mesho9975 lol
Overclocking the motor hell yea its in mans blood!
They must do that on purpose with the completely stripped screw because the same thing happened with mine.
I have a hover 1 alpha witch wire on it is it?
Dude, it would help if you point your camera at the white wire so's we can see what the heck your doing 🛴🎥😨🤛😠 hehe :)
Exactly
P
enis
With my experience on my hover 1 alpha, I can get passed the top speed by turning off and on the scooter while it’s moving. I have no idea why this effects the speed though it leads me to believe that it has something to do with the software.
U found out how to sort it properly yet I have a alpha and it only goes 12mph in sport mode
.
@@westyorkshirecarpangler Does it have the s inside the circle at the top.
@@teamnoblecar7368 yes mate
@@westyorkshirecarpangler must be because the sport mode wire inside is not plugged in
This doesn't really make it any faster... It lets the motor still run while you're going downhill, so you can go SLIGHTLY faster downhill. And it makes it to where your motor doesn't cut out when it "overheats". Which tbh, is super useful. But it doesn't make it go any faster.
This was extremly helpful!!! Thanks
Does this work for the pure air pro?
still feels and sounds like the same speed as it was when the “speed limiter” was connected so not sure if this works
might be a voltage or software based limiter if that happens, you'll probably need to try another method if you're still trying
@@CatRyu scooter stopped working lmao so i upgraded
@@sebas_69 nice lmfao
@@CatRyu yea new one is fire 😤
How do I wire a speedometer on razor electric scoorter
Shoot I dono about the razor ones. I want to buy more but man... They getting more pricey now days
Maybe using a 5/64" SAE Allen wrench instead of a 2mm metric Allen wrench for a hex screw on something built in somewhere other than the USA did the stripping?
How do you do it on a gotta v2 though I really want to know
Same here. I wanna know.
Did this while i was waiting for a new tube right after buying the thing used, thank you 👌
Does it work with the alpha??
I can do this with the hover 1 alpha?
U should put some type of Silicone to seal it good because I noticed the actual seal is ruined Once u take out the screws. And that’s very important since Water 💦 gravel dirt ect r flying through.
i nhave a seizure disorder and these scooters changed my life, is there any way to make the batteries last longer
So if we remove the speed limiter would that prevent the glitch where the bike thinks its going to fast. Since there is no speed limiter anymore?
How do you do it on a hover 1 dynamo?
The white wire does not limit the speed. I attempted this mod with no change in speed. Now I'm going to mod the controller add jumpers to bypass the on board resistors/fuse limiting the power output.
I got up to 23pmh, you have to download a GPS speed app to clock your speed. :-)
Nice! Which app do you use? I'm trying out the ride with GPS app. Not a fan of strava
@@ReginaldSharma speedometer
@@BwadeReacts Installed. There are so many to choose from. I'll update my description. It's simple and shows what matters: MPH, Max MPH and Distance Traveled.
@@ReginaldSharma I love it so far it shows the distance and speed it's awesome don't forget to lock the rotation 👍
Can be done on hover 1 alpha?? 15mph sucks
hello shawn my name is Efrain. and my question is I have a hover 1. and it wont start. I plug in the power supply, and all the lights goes on but it wont start.. can you help me with this problem. I really appreciate it
New or used? Was anything changed or don't to it which cause it not to start? If so plug or revert it back and check again.
hey sharma. its efrain again. my scooter is used. but in excellent condition. I still have the same problem. only when I plug in the charger, all everything lights up, yet no motion. it stays lit and after 2 or 3 minutes, the scooter automaticaly shuts down.
@@ReginaldSharma
Sounds to be like an electrical or motor issue. I would return it if possible. If it's was like this when you got it then it's a dud. Get that money back!
@ReginaldSharma
Hey Mr. Sharma. Is there a possibility that the controller, which is under the stand where you control the start and power to make the scooter go. There are many unlabled connections cables, some are named AYT g6, e5 and most are brown and black. Does the power, not the one which goes into the controller but the other one. Help
Hi. I'm really not sure. I personally would return it if there is any electrical issues because now you will be spending time and money trying to diagnose it. Could be controller but I can't be sure. Only way to know is replace it and see.
How can i hack the hover 1 alpha to modify the speed limit?
How about the limit of rpm of the motor
Is it fine to overclock your controller
Without relying the right amount of watts for the motor?
Cannot cause for a an overheating it?
Update it does not have any effect on your battery I get to and from from work everyday at 23 miles per hour I've been doing it for the last 4 weeks there isn't any notable change in my battery power
This DOES NOT WORK. I have two of these and modded one. Ran them both side by side and then switched people. Same result.
Hey bro when you remove the limiter it blows the motor out within a month or 2 after wards plzz be careful when doing this.. the wheel locks up when the motor blows out and hopefully your not going fast when this happens believe me I had 5 scooters already LOL
Do you know how to fix the scooter not coming on? My son rode it for less than a summer and it just cut off, and never came back on.
Dose it works with other brands?
have a mistake on my skateboard that makes me 32 and does not let me use it
You didn't show how to do Anything!!. Waste of my time!!!!
Hi Reginald, did you ever do the battery upgrade for this one? I have a journey and even though warranty its only a year, I figured once it expires ill swap the battery since ive done a few already.
I wanted to badly but then kept getting distracted by other things and never got to it. I even have all the things to make it happen … laziness happened haha
How install battery wats
I don't even have a white cable. Please help!
Same model?
You used the wrong screwdriver. They're torx heads not hex heads
I have a nilox doc, does it have a speed limiter?
Will this work on the goatex v2?
gray wire not white wire and if gray i'll just put in series of volume control so I can Adjust the speed limit not disconnected all the way as the motor will heat up and goes without limit .
Questions:My battery is flashing, but it's fully charged. Why is that?
i have the everceoss e scooter tthats capped at 25kmsph is this the same way to make mune faster\///
It's not a speed limiter it's the thermal cutout wire
@bab 119 cuts power if motor gets too hot
@@bighorse215 This is gonna be a dumb question, but if I disconnect this wire... Will my scooter set on fire or something?
@@citi360 no nothing will happen it will just allow you to keep riding when the motor gets hot.
@@bighorse215 Is that bad? I mean, I don't want my scooter to just randomly shut off on me while I'm mid-riding. But I also don't want to do damage to my battery or motor?
@@waleedabdulrab8779 honestly if everything is stock you can't really do much damage because there are still power cut out built into the battery and controller. Plus your battery will drain before you ever ride long enough to fry the electronics.
how can i increase the speed of my Xiaomi 4 pro?
Doing that removes the ipx5 waterproof seal right?
Is it working with iSooter i9 Pro? Or any advice for this Speed unlimit? Over 30km/h I need
Can you do it on go track too
MY HOVER DOES NOT TURN ON. DO YOU KNOW HOW I CAN FIX IT?
Can someone PLEASE tell me how to fix a cracked throttle button on a hover 1 journey. My daughter pressed it really hard, and now the speed works sometimes, and when it does it’s not full speed
People Health & Wealth I am not sure how to fix it but they sell replacements on their website.
Mine already came brand new with wire disconnected why
If you really wanted an extra speed, buy another motor hub + controller and boom speed will increased double your speed.
And where donu out that on the back tire???
What are you talking about?
I have the new highlander pro by them and it definitely feels like it can do better than 16 but im not sure which wire to remove
does this work the same on most scooters?
Does a halo e scooter with a tomini display go faster.
I’m not sure 🤔
Would thi work on the ElectriQ e scooter too? I'll try and Letha know
Where can I get a replacement Battery? Thank you
My best bet if you want quick is Amazon and if you want cheap then Ali
Thank you!
Is this the same for a pure e scooter?
Omg thank u so much it really helped
Does this work on indi s1?
How do I do it on a bird
thanks for thi. mine is omni 25kph I want to increase wil this work?
I have no white wires?
Willl this work on the edge 2.0?
Does this work on any e scooter
Anyone know if there is a limiter on the alpha 1?
My scooter wheel is messed up any idea on how to replace it? But i wanna do this too!
speedyescooterrepairshop.com/ visit us and ask any repair questions. We will answer any and all questions pertaining to electric scooter/bike issues. Like us @ facebook.com/speedyescooterrepair
Is it easy to do that in pure air?
Help! My front tire on my hover-1 scooter is getting stuck and it stalls out my motor. What is wrong with it and how can I easy fix it?
Deanna Vilaseca-Lopez is it the pioneer? Make sure it is inflated to 50fps and also tighten the bolts holding the wheel on (you need to remove the reflectors and the screws underneath first and then pop the black caps off)
www.speedyescooterrepairshop.com Message us there, we will answer all repair questions. Thank you. - Speedy.
Hey, is there a way to remove the kickstart? I have a hover x dynamo
Not that I'm aware of
The white plug does not effect the speed any. Don't waste your time. The only way to truely increase speed and tork is more wattage, and ampage.
Thanks, bro.
GQ @ Anything Electric
So did it work?
Yea, the white wire we can't see? The subject should be center frame.
My X hover 1 when I turn on reading E9 on display ... Can you help me?
So what was the outcome ????????
no limiting when hitting max speeds (basically bypassing heat limiter
I couldn’t find the white wire
I cant find a white wire on my scooter
I'm running 48v with a 500w controller I maxed the motor out at 32mph with 10 inch tires.
Holy hell! Pics?
Did you change out the motor and the control module?
@@alaingoindoo4705 no just the controller and throttle, you have to do some re-wiring but it's easy.
The link doesnt work.
@@alaingoindoo4705 sorry I think you have to be apart of the m365 group
can we do this on the new alpha pro ?
Any idea about yadea ks5pro?
Does this work for bird
Hi everyone so did this really work has anyone tried it how fast do you go ? Does the battery get drained faster?
Can this be done on the Hitway h5 mate
does this work the same with a eec electric scooter.(model: cp-1)
It blows the motor after a few miles that's what non of these videos tell you so dont do it
would this work on the Hover 1 RALLY ?