BetaFPV Pavo35 6s Cinewhoop for GoPro and DJI 03, Walksnail or HDZero
HTML-код
- Опубликовано: 31 июл 2024
- Here's what I like about the Pavo35:
- Lightweight + powerful design (high thrust-weight ratio)
- Functional, low-profile ducts add thrust & efficiency
- Lava 2006 2400kv motors (high kv 6s = 💪)
- BYOVTX saves 💰
- LED bling pre setup in Betaflight 🤩
Check out the Pavo 35👉
Pavo 35: bit.ly/FPV35
6s1100mah: bit.ly/6s1100
Don't forget you need a VTX 👉
DJI O3 AIr Unit: bit.ly/O3Air
DJI Goggles Integra: bit.ly/IntegraGoggles
DJI Goggles 2: bit.ly/DJIG2
The tiny Pavo Pico is fun too! 👉
Pavo Pico V2 (1.6"): bit.ly/pavo03
Pavo Pico 20 (2"): bit.ly/PPico20
Need a part for your Pavo35? BetaFPV has all the .stl files here, including several GPS mounts!
support.betafpv.com/hc/en-us/...
Haven't subscribed 🤯??? 👉 bit.ly/colibrifpv
Timestamps:
00:00 Introduction
01:55 Unboxing
02:32 Overview
03:37 Close Look
06:46 GoPro mounting
07:53 DJI O3 Installation
10:19 Installing LED strip
11:08 Flight tests
13:14 Conclusions
My Favorite FPV Gear:
Radiomaster Boxer👉 bit.ly/RMBoxer
Goggles Integra 👉 bit.ly/IntegraGoggles
Goggles 2 👉 bit.ly/DJIG2
Google V2 (renewed:) 👉 amzn.to/3L6j7GF
Best foam for V2 Goggles 👉 bit.ly/V2Foam
GEPRC Cinelog V2 O3 👉 bit.ly/CL35V2
GEPRC BabyCroc 5 👉 bit.ly/Croc5
GEPRC Croc75 V3 O3 👉 bit.ly/Croc75V3
GEPRC Croc75 V3 Frame 👉 bit.ly/C75V3F
GEPRC MK57 LR O3 👉 bit.ly/MK5D7
GEPRC MK57 LR Frame 👉 bit.ly/MK5D7F
Diatone Roma L5: 👉 bit.ly/DiatoneL5
Diatone F6 👉 bit.ly/F6BNF
My favorite FPV Stores:
BetaFPV 👉 bit.ly/BFPVStore
GetFPV 👉 bit.ly/GTFPV
GEPRC 👉 geprc.com/?ref=colibri
Diatone 👉 bit.ly/Diatonehome
* Some of these links may be affiliate links which support the channel. Thanks for your support!
#cinewhoop #pavo35 #betafpv #fpvdrone #djio3 
Авто/Мото
![J.P., NLE Choppa - Bad Bitty (Remix) [Official Music Video]](http://i.ytimg.com/vi/rBDa6BCvw10/mqdefault.jpg)
Check out the Pavo 35👉
Pavo 35: bit.ly/FPV35
6s1100mah: bit.ly/6s1100
Don't forget you need a VTX 👉
DJI O3 AIr Unit: bit.ly/O3Air
DJI Goggles Integra: bit.ly/IntegraGoggles
DJI Goggles 2: bit.ly/DJIG2
The tiny Pavo Pico is fun too! 👉
Pavo Pico V2 (1.6"): bit.ly/pavo03
Pavo Pico 20 (2"): bit.ly/PPico20
Haven't subscribed 🤯??? 👉 bit.ly/colibrifpv
I love mine, its got a ton of power especially for a cinematic drone with a GoPro and I'm also getting 7 minutes flight time with a 1000mah 6s.. The one issue I have is that you have to unbolt the bottom plate to access the 03 SD card. I have a pavo pico, a pavo 20 which I love and this drone like the others is really good.
Nice, I have also been super impressed with the Pavo35, wayyyy more power than my other cinewhoops. I couldn't believe it when I did my test flight that it hovers at like 25% throttle and cruises at like 30%. Tons of power with those 2400kv motors and yet the ducts make it pretty efficient and I'm getting super long flights. Usually you have to give up efficiency on an over-powered quad but it seems like BetaFPV found the secret sauce for this one. My favorite 3.5" cinewhoop so far!
Always great info my friend 🫡 thanks for sharing as well!
Thanks a lot for watching, really glad to get your feedback!
Thanks you for the detailed information on this. I just came across this quad on the websights, and it got my interest with the price point compared to other similar 3½" cinelog quads. Liked & subscribed
Thanks for watching, glad to have you here! When it comes to price, remember that this one does not come with a digital VTX, you have to add your own, so don't forget to add that in. Even after accounting for the DJI O3 it's still a great deal, especially the ELRS version, and I love how mine flies!
Nice review, great info. I’m actually going to be reviewing this drone soon but won’t even talk about much since you’ve covered everything so well here.
I like your thoughts regarding the Battery Cable & SD Card positions. Keep up the quality content, subscribed, cheers!
Thanks a lot my friend, really appreciate it! I really enjoy your long-range content, I learned a lot about li-ion packs from your channel. Thanks for stopping by!
@@colibrifpv Glad to hear, we gotta support quality content and appreciate the effort folks out into these videos. We certainly don’t do it for the money… haha
@@GiantAntCowboy It certainly is a labor of love and I get a lot of satisfaction out of watching and making videos 😁
👍
Awesome video! Have you had any issues with jello?
Hey! No I really haven't, almost none at all, but I do usually run a GoPro on mine and I think the weight of the action camera helps the rubber dampeners to be more effective. What small amount of Jello I do get disappears after I apply Gyroflow...
Please make a video on how to ad o3 air unit to this drone
Hey 👋 thanks for watching! There actually is already a video on the subject made by BetaFPV! ruclips.net/video/sKe_klMcy0w/видео.html
I want to use flywoo naked O3 save some weight. Slightly longer flight. Cruising with GoPro.
My Terraplane only does like 3mins though has crazy power 2306 motors and 6 blade 3.4" props
The CL35 has insane power on these 2006 motors and you still get some pretty long flight times. You'll love it!
I have it a few weeks now and wanted to add a gps but for some reason I can't get it to work. Betafpv soldered the tbs nano to the Uart 5 instead of the Uart 3 like they described in the manual. So i used uart1 for gps but it won't come in betaflight and I'm 100% sure i wired the rx and tx the right way. Should i use the uart3 probably? Awesome review by the way👌
Thanks for watching! Do you see an option to setup UART 1 in the Ports tab in Betaflight? (I don't have access to my Pavo35 right now) If so, did you activate GPS under "Sensor Input? If so, you double checked the wiring (tx to rx, rx to tx)? If so, did you check the GPS documentation on how to set it up under the "Configuration Tab, "GPS" section? [usually GPS activated, UBlox, autobaud, auto config, but some GPS units are different] And the GPS Icon still doesn't light up in Betaflight? It's usually one of those things, but if you are 100% sure it's not, then yeah, try UART 6, it's right next to UART 1, but only grab that soldering iron after you triple check the above. Good luck with it, be patient and it will work out!
@@colibrifpv thanks for your extensive reply! I'll double check everything soon and then probably try another uart. Also have to find a good place or 3d print to hold the GPS unit.
No problem! FYI, Betafpv has a pack of .stl files for the Pavo35 and the Pavo25 V2, including several GPS mounts... support.betafpv.com/hc/en-us/articles/26055868096665-STL-File-for-Pavo-25-V2-and-Pavo-35@@Flying_yesenaer
@@colibrifpv thanks a lot man🙏👍
I had a cinelog 35 quad but unfortunately it sank a month ago along with a 4 day old Gopro Hero10 :=( I really liked it because it was strong and quiet. I also tried a v2 cinelog35, which is very powerful, but also very loud. I'm thinking about a Pavo too. How loud is this quad compared to a cinelog? I appreciate your work! Thank you
Oh man, that's too bad you lost your quad with a GoPro on it, it pains me to say it but that's happened to me twice, once with a DJI O3 quad that clipped a branch over water, and once with a 7" long range with an older GoPro... ouch 😩 I also have a CL35 and this quad is quieter than a CL I think because of the duct design, but it's still loud. It makes a different noise, more of a whoosh than a scream. I prefer the way the Pavo35 flies with these new Lava motors, it's more efficient and flies longer...
@@colibrifpv Ugh, that's really rough! Unfortunately, we have to prepare for this in this hobby :( I didn't have a GPS installed, it doesn't happen anymore. I have a Pavo20 on the way and I really like the Pavo35. Thank you for the information about the quad, it helped me a lot in my decision!
How do you use the o3 as an SD card reader? When I plug my usbc to usbc cable into the o3 and then in my iPad I can only see onboard storage and not the sd card that is in the O3 unit. Any tips?
Hey there, thanks for your watching! There really is no trick, just plug it in. On my computer, both show up immediately, onboard storage and sd card. If yours is not showing up, unless you already have important footage on it can you try to format it in your goggles? Can you try a computer instead of the ipad? Never heard of the O3 not recognizing the sd card...
@@colibrifpv thanks for the reply! I’ll give my computer a try. I’m also thinking about grinding the frame down a little in that spot to give me access. Thanks!
Sure thing, good luck with it!@@KyeKunz
Thanks for the review! Would you say this drone stands in windy conditions from 10-15mph? What would be an alternative FPV similar to the Pavo 35 to also stand in windy conditions?
Hey, thanks for watching! Yes, the Pavo 35 can definitely handle some windy conditions because the ducts are relatively thin compared to other cinewhoops so it can "cut" through the wind, the motors are heavier and more powerful, and it is designed to carry heavy cams/batteries. When it comes to fighting the wind, a little weight is actually good : ) Another alternative would be the GepRC CL35. Finally, remember that no cinewhoop is going to fly as well as a traditional 5" in the wind, but that is the tradeoff for a cinematic minded drone...
@@colibrifpv Thank you very much for taking the time to get back to me. Happy flying!
You're welcome, thanks for stoping by!@@YonnBurgos
@@colibrifpvOne more question: If you have to pick a drone, which one will you go for, the Pavo35 or GEPRC CineLog35?
That's a tough choice because they are both great, but today, I would go with the Pavo35... The CL35 is more expensive but more durable (prop guards are thick, heavy, and crash-resistant) GEPRC has a better reputation for quality and is usually considered a higher end brand, and it has the DJI O3 built in already, assuming you go with that model. The Pavo35 is newer, better design in my opinion with functional ducts, it flies better and longer, and it is cheaper (even considering the cost of the DJI O3) but you do have to DIY the air unit and the ducts are not as durable, but they are cheap to replace... @@YonnBurgos
How is the 03 footage in windy days?
It's actually very good...any cinewhoop is going to get blown around in the wind due to those ducts/prop guards, but this over powered 3.5" is going to do much better than most other cinewhoops in the wind, especially with a heavy battery, and Gyroflow does wonders to even out any wobbles!
Led cable only 3, red 5v, Black GND , yellow Led stripe or what?, I use led stripe pad and has setup chanel aux on my TX, but nothing hapen,
Hey there, sounds like you have it wired up wrong. The LED strip that came with Pavo35 should just plug into the provided plug. Mine was wired backwards though, so double check your wiring. Then check in Betaflight that your switch is recognized, assign it under the modes tab and you should be good to go!
Thank you for the review !
I got mine (with DJI O3 too), and i get massive jello when flying without ND filter, just with a simple hovering ! Changing props, new o3 cam, check all screws, add extra soft-mount on cam and motors, betafpv tune or BF stock tune, ESC 48/96Khz... nothing help for the Jello, however quad sounds good when flying 🤔
Did you have a ND filter on the DVR footage from your review ? Seems to be OK on your side.
Hey, thanks for watching! Yes, I am using an ND filter on mine and I wasn't having those problems with Jello, although I didn't build or tune this one myself, it's the pre-build version from BetaFPV and I thought the tune was pretty good. Here is the stock tune from BetaFPV if you want to try it out... support.betafpv.com/hc/en-us/articles/25591364337177-CLI-for-Pavo-35-F722-35A-AIO-V2
@zefrog69 did you ever get your jello issue figured out? I just got mine built and have lots of jello in the O3 camera.
Don’t have ND filters, but it’s shouldn’t be like this… let me know, thanks!
@@colibrifpv Many thanks for your feedback. Unfortunately, i have already the betaFPV stock tune from official dump :(
@@GiantAntCowboy Issue is not resolved for now. I am currently getting another brand new one from a local store, and i asked them to test outside "without" ND to check on their side. Can we share together a small footage during an hovering ? In order to compare and confirm we have the same issue ?
@@zefrog69 did some troubleshooting tonight and found in my case the two rear motors both vibrate at certain rpm, around 1248 in the Betaflight motors tab is very bad. If I shut down those two motors the quad is runs smooth & quiet.
I tried updating the ESCs, and changing the PWM frequency, but neither helped.
I just sent a message to BetaFPV about it; I’ll try to share some footage, but it’s just jello are low throttle cruising. Do you have any footage?
Hope we get this figured out, otherwise it’s a nice quad.
i am new to the world of FPV, I only fly DJI,i would like to know what RC I should purchase to use crossfire whit the O3, I was planning to buy the radiomaster TX16s, can crossfire be used whit that radio ??????
Hey! Yes that would work but you would need to purchase a crossfire module like this one [bit.ly/CRSFTX ] because that radio comes with either ELRS or a 4in1 module built in. If you ONLY plan to run crossfire, why not the TBS Tango? It's what I use, it's portable and feels great! [ bit.ly/TBSTango ] If you go with the Radiomaster, recommend getting the model with ELRS, then add the crossfire module. It will be expensive and bulky, but you will have the best of both worlds and be relatively future-proof...
so do you recommend me the model whit ELRS and then buy the crossfiremodule separately ??
and the version 4in1 model how it works @@colibrifpv
The 4in1 module is for older protocols like FRSKY which are not used as much nowadays, so unless you plan to use old drones, don't get the 4in1 version. If you are just getting started I recommended getting either the TBS Tango 2 radio (crossfire) or the RadioMaster ELRS radio (ELRS). Just choose one, they are both great, you won't go wrong either way, crossfire is probably more reliable but more expensive, ELRS is 95% as good but much cheaper. Either one will serve you well!@@videocrudo5954
ok thanks a lot@@colibrifpv
My pavo 35 has a flutter sound on throttle up with running a gopro 12 on it
That doesn't sounds right, maybe you have a bad motor or ESC? Have you tried playing with the tune?