DJI RC Antenna MOD - NO drilling/cutting etc. ALFA APA-M25
HTML-код
- Опубликовано: 23 авг 2024
- LINKS BELOW!
DJI RC Antenna modification, replace two standard antennas for two directional ALFA Network APA-M25. The modification uses only existing holes to route the antenna wires for external Alfa antennas.
DJI Mini 3 Pro
Bracet STL file: www.thingivers...
Antenna wire (10cm RP SMA Female to U.FL IPX) pl.aliexpress....
Antenna 2x Alfa Network APA-M25 www.amazon.com...
![Tee Grizzley - Detroit (Feat. 42 Dugg) [Official Video]](http://i.ytimg.com/vi/aeKfTtt0x14/mqdefault.jpg)
LINKS FOR PARTS IN DESCRIPTION
I like to ask you since you open the controller I know that no HDMI output is build inside the controller so only output is through USB C but you get a full OSD in video instead only video from drone camera. So do it have an option in the board for that or not?
@@dejanpetkovski8761 :P I’m not sure what you are asking for :P. There is no extra output inside. I get OSD on my videos because I use screen recording (standard option) instead of drone recording (also standard option). In DJI RC, there is no option to connect an extra screen, but generally, it’s possible. DJI RC is built on Android and can transfer the view to USB-C. The problem is that the DisplayLink Driver is missing. If you can install the driver, then you can connect an extra screen via USB-C, but for driver installation, ROOT is necessary.
@@moskil2Ok my bad my point was you can use USB-C for for an output not extra screen but then you get OSD also for example i like to connect USB-C for output to an video switcher or mixer so the video be streamed but also you get OSD too on video output. That is my question because on some board you have empty space for HDMI or other connector and you need to pay extra for one connector that have place on board mut for cheap variant is not installed, this is just hypothetical for the DJI RC i have seen many board that have that option and therefore i ask you because you open the DJI RC. :) I hope you understand me now.
Great mod! Clean!
Does this mod work for the DJI RC-N1 controller for my Dji mini 2?
Można do samo zrobić przy mini 4 pro kontroler bez wyświetlacza?
Raczej nie ma sensu w mini 4 anteny sa poprawione
Mam max zasięg 1200 metrów w małej wiosce bez dużych budynków. Jeśli lecę w kierunek gdzie przeszkodą jest duże drzewo zasięg spada do 700 m. Czy to normalne?
@@deskjet0313 Normalne, trzeba latac tak by unikac przeszkod bezposrednio miedzy pilotem a dronem
Do you perhaps know how to change the batteries? I cannot find any information whatsoever anywhere on this. Thanks!!
If you’re asking about the battery in an RC controller, it’s quite easy. The batteries are connected by small plugs, so you simply need to disconnect them. The plugs are under small black pieces of fabric 1:44. After that, cut the wires from the old battery and solder them to the new one. You can purchase cells with pre-welded nickel plates for easier soldering, similar to the ones available here: tinyurl.com/bdhkfej7. The original battery has a capacity of 2600mAh.
@@moskil2 Thank you! I did open the RC. There are 2x 18650 2600 mAh 3.6V batteries with special connectors. So no special controllers. Batteries can be switched between each other so they are not paired to the BMS and could be replaced I think. But DJI has a bug there and they must know about it. If you have an issue with quick battery drain (despite RC 1 year old), when you disconnect the batteries at 0%, they show around 70%...you drain them back to 0%, disconnect again and they show around 25%...you repeat that around 3 more times until they are really at the lowest and the RC cannot be turned on. You charge them back to 100% in 3 hours (took around 30 minutes before) and they last as new. This means they get, after some time, discalibrated and the BMS is not able to get proper 1 - 100% limits. This information is not mentioned at any of the forums yet.
Hello, I would like to purchase alfa network apa-m25+bracket. Please give me the purchase link.
There are links in description, u can buy all stuff and print bracket.