maaaan every time i see a new one of your videos i remember all the cool toy guns youve made. you seriously have "IT" man! i sincerely want one of your creations
Bit overkill on the firing pin spring, but it will fire… Once… Then, you gotta worry about a potential case rupture shooting back at ya. But it may not… One way to find out
Nice and now with a good grip (you aren't shoving that in your pocket, so a full length pistol grip is IMHO a must), plz :D (and of course magazine fed!) :D
After all of the extra steps taken and attention to detail, I am surprised you decided to connect the grips with adhesive rather than screws, as a gunsmith it feels a little sacreligious. Thats literally the only nitpick I can find, this whole video is incredibly impressive.
would this kind of setup, the metal spring, or whatever, would lose its strength after a while? from the way the metal is compressed, those two points would eventually become structurally compromised, as the strength isn't uniformly distributed, as opposed to the way a spring is being compressed inside of a watch. When hard metal bends repeatedly it becomes softer and softer.
There are some things best done the old ways that 3D printers can’t do as well and the traditional methods are more rewarding because you can say you completely made it by hand without taking the 3D printer short cut, craftsmanship still has more meaning than easy quick builds but that’s just me
@@dragonslyer74 as I always say “whatever works” I don’t want to be snooty or picky if I came off that way, I just like seeing people do things the old way as well as the new because there’s just a special feeling about the traditional way to me
Хорошие керны получаются из длинных бит-отверток для шуруповерта. Вставляешь в патрон дрели и обтачиваешь рабочюю часть шлифмашиной или наждачной бумагой - получается хоть керн, хоть шило. Сталь S2 очень хороша. А сверху на керн можно одеть кусок резиновой трубки для хорошего хвата.
cool, but it is possible for the bearing to go off track before full departure and go toward the shooter. unless im over looking something that has my thinking incorrect
не понял одного момента - если у него есть фрезерный станок, он там всякие пазы делал, зачем он под курок дыру вручную выпиливал, и второй момент - зачем надо несколько слоёв фанеры склеивать, а цельная доска не канает ? 🤔
@@serengyarchery , токаренный мощный ствол, крепление " часовой " основной пружины, магнитный замок крепления снаряда, пружина замка- спуска и ее установка прямо в канал рукояти. Только не понял все же , из какого материала шасси(корпус)- вначале вроде из прессованого картона наборная, собранная с эпоксидной смолой, а дальше больше походит на эбонит. Только детали УСМ все же не лучше было бы сделать стальными, чтоб меньше изнашивались?
This is cool. I get great joy from target practice with any gun or gagit that shoots. Unfortunately, here in CA, they cover everything by making it illegal to launch any kind of projectile no maker what it is so I could technically be in trouble if I made and fired this type of gun. Even a blow gun is illegal !!!!
oh for sure, coping saws are pretty cool and useful for smaller projects that require fine detail. there is definitely an art to it. easy to learn hard to master.
Imagine this scaled up to the size of a minivan. It uses, like, semi truck leaf suspension springs.
Good idea
@@serengyarchery good idea?😨
@@jajoothecoolmanthe atf will ban tactical leaf springs soon
an inverse ballista
I think you might be onto something
This is awesome, I am very impressed by the whole build and the level of detail you put into this, nice work!!
Thank you friend.
maaaan every time i see a new one of your videos i remember all the cool toy guns youve made. you seriously have "IT" man!
i sincerely want one of your creations
What an interesting toy, unfortunately I don't have the tools to make it.
put rifling in the barrel and ever so slightly extend it so the magnet speeds up better
I might actually build that homemade "gun" myself, that's how much I like and think that this is interesting.
Thanks friend for your support
@@serengyarchery You are welcome friend.
If you put a firing pin on on the end of the spring ands a 9mm barrel…. Single shot pistol.
Bit overkill on the firing pin spring, but it will fire… Once… Then, you gotta worry about a potential case rupture shooting back at ya. But it may not… One way to find out
Shh! Don't give ATF reasons to ban this!
@ItMeArchie You can order rifled barrels online if you want more accuracy
Nice and now with a good grip (you aren't shoving that in your pocket, so a full length pistol grip is IMHO a must), plz :D (and of course magazine fed!) :D
Мастер!
Без понтов. Спасибо.
That's basically just a modern crossbow
An archers concealed carry XD
Well done!!!!
you're smart.. and revolutionary
Thanks friend for your support
10:04 that scratch is going to live in my mind forever
Ya
i can feel you.
How could you...
My mind successfully ignored it the first time, now I've been forced to acknowledge it 😂
So cool ! 👍🏻👍🏻(by the way...what is the green compound?)
Thank you. This is GOI polishing paste
@@serengyarchery Thank you. Im a fan of your channel. Will make some with your instructions. 🤸🏻♀🤸🏻♀🤸🏻♂🤸🏻♂👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻
@@timbatimbero3934 Thanks friend for your support
I like to pretend that when it speeds up, its actually not sped up, they're just moving that quickly. Its minor, but very entertaining.
Merci pour votre travail et pour la vidéo ! J'adore !
Thanks friend for your support
Great work and clever idea! Beautiful gun! Thanks for showing us how to make it! Cheers!😀😁🔧🛠️
Thanks friend for your support
Such a well-made creation.
pretty slick little slingshot. Well done
Imagine a design with a colimaçon Spring 😂👍
Good idea
Awesome job! Fun to watch!
Nicely done!!!
So cool ❤❤❤
After all of the extra steps taken and attention to detail, I am surprised you decided to connect the grips with adhesive rather than screws, as a gunsmith it feels a little sacreligious. Thats literally the only nitpick I can find, this whole video is incredibly impressive.
Thank you. the thing is that I didn’t have the material of the required thickness, so I had to glue the sandwich together
where do you get the spring steel from ?
this spring is from a vacuum cleaner
looks like the pull start recoil spring from a string trimmer is similar in size maybe
Super idée 👍
Je likes,
fabriquation artisanales, armement à billes d'aciers.
Thank you friend for your support
@@serengyarchery
You did it really cool. 👍
Amazing, i never thought brilliant idea like that
👍👍👍
Parabéns muito bom, gostei muito.😊🎉🎉
Please try making the metal on the left and right sides of the spring, it would give the effect of a tapered spring, greatly increasing power
Good idea
Great work my friend 😎
Thank you friend.
That's a cool gun, looks fun. Thanks for making it Me
you're welcome
This is very cool. Keep up the good work
Thanks friend for your support
Nice, very creative
Damn, the Acorn Cop is having true nightmares now. Well done
Hahaha!!
Ingegnoso ! Complimenti … 👏🏻💪🏻⚙️
Cool. Not clear to me what keeps the steel ball on track.. ?
There is a magnet installed
@@serengyarchery Yes. I meant at it travels out of the gun. I guess there is a small groove above and below which keeps it in line.
would this kind of setup, the metal spring, or whatever, would lose its strength after a while? from the way the metal is compressed, those two points would eventually become structurally compromised, as the strength isn't uniformly distributed, as opposed to the way a spring is being compressed inside of a watch. When hard metal bends repeatedly it becomes softer and softer.
Perhaps something will happen over time. but it changes very easily
Beautifully made, quality toy. Nice.✓
Thank you
That's pretty cool
Очень аккуратная работа.
Very C❄️❄️L design
Leaf Springs is honestly kinda ingenious
Thanks friend for your support
Creative❤
There are some things best done the old ways that 3D printers can’t do as well and the traditional methods are more rewarding because you can say you completely made it by hand without taking the 3D printer short cut, craftsmanship still has more meaning than easy quick builds but that’s just me
Thanks friend for your support
What if the person dose the complete render and 3d modeling
@@dragonslyer74 as I always say “whatever works” I don’t want to be snooty or picky if I came off that way, I just like seeing people do things the old way as well as the new because there’s just a special feeling about the traditional way to me
@@dragonslyer74still easier than milling
I'm calling the ATF
Fun fact this gun was made by "me"
that one unemployed friend at 7:00 am on a tuesday:
a weapon to surpass metal gear
Well done!
Thank you friend.
How far does it shoot tho
Not very far. Need a stronger spring
Isso aí parceiro, show de bola
Att: Weliton Marks - Canal Desbravatube
👍
Хорошие керны получаются из длинных бит-отверток для шуруповерта. Вставляешь в патрон дрели и обтачиваешь рабочюю часть шлифмашиной или наждачной бумагой - получается хоть керн, хоть шило. Сталь S2 очень хороша. А сверху на керн можно одеть кусок резиновой трубки для хорошего хвата.
Спасибо. отличная идея
Good but very good
Ah! I love this design! Though mine used more parts. It reminds me of the Shambler. A shotgun made of scrap parts, you should take a look at it!
Thank you friend for your support
АБАлденноо ооочень понравилось !
NiTiNol springs would be really awesome powerful in this design idea
Good idea
are you selling these?
Unfortunately, I'm not selling anything right now. maybe in the future
Oh man that is so cool it's like a crossbow but really weird
Thank you friend.
Incredible❤
Thank you friend.
@@serengyarchery You're welcome.
Very clever I like it
Thank you friend.
cool, but it is possible for the bearing to go off track before full departure and go toward the shooter. unless im over looking something that has my thinking incorrect
This is a toy. Don't expect great accuracy
Интересное решение с такой пружиной! Правда маловато в ней запаса энергии для разгона такого свинцового грузика.
Согласен, эта пружина слабовата. всегда можно поставить мощнее.
не понял одного момента - если у него есть фрезерный станок, он там всякие пазы делал, зачем он под курок дыру вручную выпиливал, и второй момент - зачем надо несколько слоёв фанеры склеивать, а цельная доска не канает ? 🤔
@@user-vb3bp4xw1qну цельной видать не было. очевидно же.
Good❤👍
the gun couldve been a lil bigger in my opinion but good job
Thank you
With all that equipment and know how .. he could be turning out some righteous firearms
the law doesn't allow
@@serengyarchery
My understanding is that you can make your own firearms for your own use … you just can’t sell them
what's the FPS on that? 400?
Much less
👍👍👍🔥
Thank you
very interesting!
now just make a mag that attaches and a part that loads a bullet once its pulled back
Good idea
good job
Great !
nice gun！
Halo gun :)
And they said guns don´t go to heaven x)
Привет.
Интересная конструкция- не только основное решение, но и в отдельных узлах тоже.
Спасибо. Какие узлы вас впечатлили?
@@serengyarchery , токаренный мощный ствол, крепление " часовой " основной пружины, магнитный замок крепления снаряда, пружина замка- спуска и ее установка прямо в канал рукояти.
Только не понял все же , из какого материала шасси(корпус)- вначале вроде из прессованого картона наборная, собранная с эпоксидной смолой, а дальше больше походит на эбонит.
Только детали УСМ все же не лучше было бы сделать стальными, чтоб меньше изнашивались?
@@Al.P. Да ты прав рукоятка сделана из Эбонита.
Brilliant.
대단합니다 팔도강산낚시 🌿🌿
Das ist cool.🤘🤠
Thank you friend.
@@serengyarchery Good Work, Grüße aus Deutschland
@@daniloweifu9566 you're welcome
С твоим уровнем мог бы сделать что-то более поинтереснее, с пружиной например и шарами по 8 мм. Сделай пожалуйста!❤
Хорошая идея. Думаю дойдет до этого время
Very simple but inspiring 🙌🏻🙌🏻🙌🏻well done . Now get your 0 push ups done
you're welcome
This is a dangerous fully semiautomatic ghost assault rifle
2:04 anyone else hard?
You know what's crazy? That's WOOD!
Quedó muy bueno, hay que comercializarla, para espantar cat and dog 😂 imprudentes
I wanna make this now :P
Nothing is impossible
QUE BUENA HERMANO ERES JENIAL PA...
Thank you friend.
❤ w¿+% u pas umm
What. Not new
Q. Cook ing. Toy
Brillante fabrication !!!
Le même genre de petit instrument 'handmade' tirant une vraie balle, cela existe-t-il ?...
I don't think it will be effective
Very cool.
Thank you
This is cool. I get great joy from target practice with any gun or gagit that shoots. Unfortunately, here in CA, they cover everything by making it illegal to launch any kind of projectile no maker what it is so I could technically be in trouble if I made and fired this type of gun. Even a blow gun is illegal !!!!
Even so. I didn't think it was so strict in California.
Could you try putting a nail as the projectile instead
Good idea
Looks almost like a little Makarov.
creative peak
Dope
Make the grip slightly larger and hollow to store ammo and you're good to go.
👍👍👍
Danke für die info,
Give me the mold of the mechanism please
Can't you see it in the video?
Forget the push ups that little saw you've got look's like a right work out itself lol
oh for sure, coping saws are pretty cool and useful for smaller projects that require fine detail. there is definitely an art to it. easy to learn hard to master.
This would be a good scifi gun.
Thank you
@@serengyarchery how did you bevel the edges of the wooden pieces on the handle?
3:46 music to my ears lol