how to replace rear brake pads and rotors 2018 lexus nx 300 with electronic parking brake replacemen
HTML-код
- Опубликовано: 14 окт 2024
- how to replace rear brake pads and rotors on 2018 lexus nx 300 with electronic parking brake, how to retract the piston on the caliper the simple way with no steps and no fancy scanner, straight to the point
Thank you for this video, knocked out my brakes in 40 mins. Was alot of help
Im glad you did a great job and thanks for watching.
Great informative video. Used portable power station to loosen brakes. Removed, then ran ea brake out till boot was smooth. Cleaned, then pushed back in w brake compressor tool. Boot realigned smoothly. Thanks for the info, very helpful.
Thanks for sharing, that is very appreciated.
Hey there my brother. Thank u for an awesome Vid. I want to ask you about a 2004 Monte Carlo LS. It cranks up but dies in 2 seconds. Any idea to lead me in right direction??
hi, have checked for codes stored in the PCM? start by scanning it or if there is a scanner with the ability to read live data at the moment of cranking it that can tell you a lot of what is happening, disconnect maf sensor and try to turn it on, if it runs fine then dont look farther, but scanning it or live data is the best way to go. since there are so many things that can cause the engine to turn on only for few seconds.
Thanks for the video so very helpful, where and how to make that cable going to 12v to the parking brake? Thanks a lot🙏
regular 12v battery jumper cables so you connect it to the battery of the car, thanks for taking the time to visit this channel.
Thanks for a good video on this subject
Glad you liked it! and thanks for visiting this channel.
Great video, straight to the point. Thank you for your time making it!!!!!!
thank you appreciate it very much.
On the passenger side the rear wheel, which one is positive and which one is negative? Is it same in your video?
it is the opposite but in case if you apply 12v on the wrong side, be ready to take off one wire immediately so it will stop turning because if the piston comes out too much then you will damage it, also be ready to take off one wire from the connector when the piston has reached all the way inside exactly on the same edge of the piston so brake pads will not interfere with brake pads.
Hey why didn’t you just do the brake release procedure to loosen the rear brakes off?
there was a malfunction in the brake system and the buttons were useless but once i finished the job no more brake system malfunction.
Can I use an 18 volt battery to reset the brake piston, as in this case?
I would not suggest you to use a 18v battery since the system is designed for 12v, you also can try to desingage using the screen inside your vehicle.
I didn't know this and i accident let the electric break running and push the piston all the way out. I put it back in and install new pad. But now display show that ( electric break mulfuntion) and the electric break button doesn't work anymore. Can you please show me how to fix that problem. Thank you
sorry for the delay but i was out of State, when the EPB malfunction apears n you follow the steps to reset it n it does not work then a good scanner is needed so the scanner can give you clues of what caused the issue or even reset it, ( Switch the ignition to the ON position and shift the gear lever in PARK. ...
Pull and release the EPB button to activate the electric parking brake.
Pull and hold the EPB button until you hear a mechanical sound, then release the button). if it doesnt work then it is best to go to the dealer.
@@JM-AUTO i already try and it doesnt wwork, bring it to the shop and they hook up their goood scanner and did a reset adn now it goood to go, thank you very much for response.
@@HungLe-ek4zj You probably need to clear the memory of the brake system. That will reset the parking brake errors and you can proceed with your next step, whether it be replacing the pads or ready to drive. See this link:www.clublexus.com/forums/attachments/nx-1st-gen-2015-2021/480837d1598308629-how-to-manually-release-parking-brake-when-battery-is-dead-nx300-manual-parking-brake-release.docx. I found that in the ClubLexus forums : www.clublexus.com/forums/nx-1st-gen-2015-2021/950980-how-to-manually-release-parking-brake-when-battery-is-dead.html. Helped me out with my issue and now brakes are released and pads are ready to install. Good Luck!
Thanks for your instructions. It was VERY helpful to see your video. Thank you very much for your help!
@@jonathancard1613 thank you for watching my videos, I really appreciate it.
Are the 12 volts coming from a battery?
Yes from the same vehicle's battery.
What did you use to supply the motor the 12 volts
I used the battery from the car.
Thank you bro!
Any time thanks
H9w about passenger side? Same positive towards backside?
Yes it is the same just to make sure always put connect one wire and the just touch the other pin with ther wire and be ready to disconnect it in case it is coming out
Thank you man
You're welcome! and thanks for watching.
Thank you share clip
thanks for coming to my channel.
Ghetto way do it. U gonna break your car Forsure haha backyard mechanic
thanks for watching.