Bro switch used for latching purpose are special? Because if they’re n.o switch then how are they completing the circuit without being pushed physically? How they get disconnected on pushing n.c switch?
Same address ho to nc , no ho jata hai aur no , nc ho jata hai . Jab output ko supply milega to vahi address no ko bhi diya gaya hai to no , nc ho jayega aur output ko couninue supply milti rahegi
Kuchh bhi le sakte hai lekin output ek hi hai isiliye Q:0.0 liya hai ap 1 2 3..kuchh bhi le sakte ho lekin ek se jyada output ho to serial no. Me rahega to achha dikhega
*this video wrong information.* if i push (NC) button and hold motor not run but if i not hold push close than motor again run brother. concept not clear.
Plc programming in hindi: ruclips.net/p/PLDmHF8ZldpgcHceI4tquBp2UjIVROPqi4
Very good explanation.Thank you sir ,me from Singapore
outclaassss very well explained
Bro switch used for latching purpose are special? Because if they’re n.o switch then how are they completing the circuit without being pushed physically? How they get disconnected on pushing n.c switch?
Thank you for making it so simple.
Kya latching hamesha NO hi hoga, NC kab use kar sakte he .
Sir ye jo latching ke liye NO switch lga hai ye physically kaha lgega
sir neacha wsala tu close kya ni ap ne tu i0.0 ko chorne se supply neeacha wala switch se kse pass ho rhi ha?
Kyuki output or niche waale ka same address hein, es liye jab output on hua tab hi niche wala on ho gya..
acha same adress ki wjha se open switch bhi close ho gya acha thanks sir@@vidyatrans
Very good teaching skills
Never seen my life
Awesome teaching. Thank you
Glad it was helpful!
Nice helpful video sir
nc ko hum pehle bhi laga skte the na ?
Yes!...
Sir nc me address value konsi dalte hai
Input ka address
Very nice sir 👌👍
Supply kha jari he bhai i0.0 jo neeche vala he usse supply bina btn dbae kese jaegi n.o he bo
neeche vala i0.1 hai joki equal hai q0.0 ke tabhi to lach banega bhai
Sir video private kyun kar rakhy ho?
Bhai sahi hai ek dum videos
Tuje kis ne pucha …?????? Hmko pata hai ye best hi hai …..
Isme Q.0 no h to continue supply kaise mil rha h 7th video me
Same address ho to nc , no ho jata hai aur no , nc ho jata hai . Jab output ko supply milega to vahi address no ko bhi diya gaya hai to no , nc ho jayega aur output ko couninue supply milti rahegi
Thanks sir...nice video
Q0. 0 input band q nhi hota
Woh niche waale address s path le leta hai.. check next lecture
Q ki vo bhi no h na
Jo on rakhne ke liye Q0.0 liya h
Use Q0.0 hi ku liya kuch or nhi le skte
Kuchh bhi le sakte hai lekin output ek hi hai isiliye Q:0.0 liya hai ap 1 2 3..kuchh bhi le sakte ho lekin ek se jyada output ho to serial no. Me rahega to achha dikhega
It's like a Dol starter
Ab samajh gye
Thank you sir
thanku bhai ji. ..
Ismen galat hai sir off pb on pb se pehle lagega correction it .otherwise fundamental clear karenge please.
Bro please give acess to provate video
All lectures are paid you can whatsapp me at - 9027276360.
abey set reset bit ka bhi toh bta
Very nice sir
Awesome sir👍👍
धन्यवाद
Thanks sir
Pichli video ki galti thik kar li aapne
Maine pichli video mai bhi koi galti nhi ki..
Good
Latching min's use 1button and 1 press on and same button on press off but you use two button its not latching
Latching means become fixed in a particular state.
*this video wrong information.*
if i push (NC) button and hold motor not run but if i not hold push close than motor again run brother.
concept not clear.