Hey! thanks for the video, l just did the same procedure on my new dt M 1900 , same spline as you but it seems a bit thight so the freewheel pushes the transmission forward
Hi wanna ask about freehub body. Do you know which brand using steel freehub body? Most brand using aluminum and after several years the cassette chew the body really bad
Hi, I have old specialized stumpjumper fsr 650b, with wheelset Roval 650b, alloy, 29mm inner width, 24/28h, with rear hub Specialized, Hi Lo disc, 4x sealed cartridge bearings, 12mm thru-axle, 28h. . Can I use this to upgrade my stumpy from 10 speed to 11/12 speed?
Great videos. Im looking at picking up a decent bike but with a not so decent groupset (eagle SX). Rear hub is Novatec Boost 12x148mm. Can I change to microspline same as in this video to allow an SLX / XT groupset upgrade?
Like the video but, it's a costly upgrade shifter, cassette, derailleur, and freehub. Many are going with the 11 speed 11-46 or 11-50 sunrace cassette. It's noisier, but works
Hi. I have a brand new dt swiss 350. But we changed the free hub to microspline. Right now, it doesn't sound like the original sound. Can u help me? Thank you
Hi, is this possible with the 180 hubs in 142mm width and with ratchet EXP and straight pull spokes by using the HWYCBL00S5375S microspline driver? any thoughts much appreciated
hi im having issues putting this exact same microspline hub on the rear axle that previously held the old school shimano hg hub on my 2018 Diamondback Release 1 27.5. however the new MS body is not sliding all the way in as it hits a certain point it cannot pass on the rear axle, any suggestions?
Say I have DT Swiss EX 1501 Spline One with 240s ratchet with freehub that fits the cassette of Shimano 10 speed. Then the freehub is worn out by my 80Nm E-MTB motor. So I order an steel-made freehub on Amazon from the DT Swiss official retailer. It says "fits current 180 240 and 350 hubs". So does it really fit the hub without additional/different end cap?
@@FreeToCycle thanks for reply! Did you try it? Im thinking because i swapped my dt swiss 350 142mm to QR. The micro spline free body comes with 142 and 148 end caps. Hmmm..if QR fits 142, i dont see a reason why it shouldnt fit microspline..hmm I emailed DT SWISS, waiting for their reply
@@FreeToCycle i spoke to DT SWISS!!!! Theres a “microspline QR compatiable, with the Microspline QR end cap, which is different than the 142-148 end cap/ micro freebody. Only negative is i purchased the 8-11 speed QR end cap, and i just purchased the QR microspline end cap with QR microspline freebody Learned something new today
Yet again, you come to the rescue. A very trustworthy source of information.
Hi Many thanks for your great videos on you tube.Thank you for sharing your knowledge with fellow cyclists 👍👍👍
Better than DT's official video thank you
Thanks for sharing the information and video. I have upgraded my 10 speed to 12 speed base on your video. It went very well. Thanks once again!
Perfect & thanks. Just installed my MS & XT 1x12 cassette according to this, so thanks. I didn’t grease enough, so I’m glad I saw this.
Thank you. Just the video I need for changing standard to micro splin 12 speed.
Best cycling channel on YT. Thank you for all you do mate.
Thanks! There be lots more to come so stay tuned👍
Great info! Keep them coming!
very helpful indeed, thanks a lot.
Hey! thanks for the video, l just did the same procedure on my new dt M 1900 , same spline as you but it seems a bit thight so the freewheel pushes the transmission forward
thanks for the Video,Sunrace thought about putting a 12v cassette with hg body
Great tips for the guys new to diy bike repairs. What wheelset model are these?
does the shimano HG hub interchangeable with this DT freehub?
Can you put a rapid drive 6 pawl on that?
Will the DT micro spline freehub work on the DR350 **rim brake** hub?
Hi wanna ask about freehub body. Do you know which brand using steel freehub body? Most brand using aluminum and after several years the cassette chew the body really bad
Hi, I have old specialized stumpjumper fsr 650b, with wheelset Roval 650b, alloy, 29mm inner width, 24/28h, with rear hub Specialized, Hi Lo disc, 4x sealed cartridge bearings, 12mm thru-axle, 28h. . Can I use this to upgrade my stumpy from 10 speed to 11/12 speed?
Would this be the same procedure on the shimano splines
Not the same setup as a Shimano hub.
Great videos. Im looking at picking up a decent bike but with a not so decent groupset (eagle SX). Rear hub is Novatec Boost 12x148mm. Can I change to microspline same as in this video to allow an SLX / XT groupset upgrade?
Any chance you did this in the end? I'm looking to upgrade my SX drivetrain to XT soon!
hello! if my bike has 9x135qr on the back what kind of dtswiss hub can i get?? i also have 2x11 shimano
Can microspline free hub body compatible to bontrager wheelset?
Like the video but, it's a costly upgrade shifter, cassette, derailleur, and freehub. Many are going with the 11 speed 11-46 or 11-50 sunrace cassette. It's noisier, but works
Hi. I have a brand new dt swiss 350. But we changed the free hub to microspline.
Right now, it doesn't sound like the original sound.
Can u help me?
Thank you
which hub model ? nice video
Anyone know what bearings are on the wheel, I need to change mine but its hard to find the correct one.
Hi, is this possible with the 180 hubs in 142mm width and with ratchet EXP and straight pull spokes by using the HWYCBL00S5375S microspline driver? any thoughts much appreciated
Yes you can purchase the exp microspline freehub body and swap it over!
hi
im having issues putting this exact same microspline hub on the rear axle that previously held the old school shimano hg hub on my 2018 Diamondback Release 1 27.5. however the new MS body is not sliding all the way in as it hits a certain point it cannot pass on the rear axle, any suggestions?
are there micro spline bodies that have different clearances for axles?
Say I have DT Swiss EX 1501 Spline One with 240s ratchet with freehub that fits the cassette of Shimano 10 speed. Then the freehub is worn out by my 80Nm E-MTB motor. So I order an steel-made freehub on Amazon from the DT Swiss official retailer. It says "fits current 180 240 and 350 hubs". So does it really fit the hub without additional/different end cap?
The freehub body should be a direct swap!
Thanks for video, its possible to instal freehub MS with ratchet ? thanks
Yes you can get a ratchet version of the Micro Spline Freehub
@@FreeToCycle thanks for answer, after question I saw your video regarding that ...so many thanks again ;)
Can you change out any free hub body to the DT microspline?
Any MTB DT Swiss 11 speed through axle freehub can be swapped for a Micro Spline freehub body!
Hi is this the same for the DT X 1900 wheelset?
Yes!
Does this fit onto the G 1800 gravel wheel?
Yes!
@@FreeToCycle thanks for reply.
1 more. Do they come with the conversions to quick release end caps my frame.doesnt support thru axle
Thur Axle only for the microspline freehub!
@@FreeToCyclethanks for answering so quick.
Thanks for the video. Do you use grease or oil on the paws???? I have been told oil before....
DT Swiss grease on the pawls!
@@FreeToCycle Thanks, I just ordered the upgrade for the ratchets and the micro spline so fingers crossed.
@@FreeToCycle Thanks for the help, I just switched my Santa Cruz wheel over and upgraded to more teeth at the same time. It was easy peasey
Worked like a charm, now I have a back up wheel for my 12 speed
Can micro spline fit Dt swiss 350 hub with QR end caps?!
If i swap the freebody to microspline
Not compatible with QR caps!
@@FreeToCycle thanks for reply!
Did you try it?
Im thinking because i swapped my dt swiss 350 142mm to QR.
The micro spline free body comes with 142 and 148 end caps.
Hmmm..if QR fits 142, i dont see a reason why it shouldnt fit microspline..hmm
I emailed DT SWISS, waiting for their reply
142/148 are thru axle end caps, QR caps are for 130 or 135mm rear dropouts. You can't use QR in a 142mm rear dropout!
@@FreeToCycle i spoke to DT SWISS!!!!
Theres a “microspline QR compatiable, with the Microspline QR end cap, which is different than the 142-148 end cap/ micro freebody.
Only negative is i purchased the 8-11 speed QR end cap, and i just purchased the QR microspline end cap with QR microspline freebody
Learned something new today
Still won't work with a 12 speed mtb cassette in a 130 or 135mm frame! I have already done a video all about it on the channel!
Does it fit a DT swiss 370 hub?
Yes!
My free hub body won’t click in-the springs push it out and the endcap it’s not holding it
i noticed that non Shimano Micro-spline only have 22 splines. Shimano has 23 splines.
I just can’t remove the freehub… tried both ways 🥺
ruclips.net/video/BhViK5Mmj0U/видео.html