How do I properly simmulate two connected threaded parts where both male and female parts are important in the analisys? I tried running a 3d static study using extruded threads modeled with the swept boss and cut features with helix path and ISO metric screw thread profile and no penetration connection between parts. This study resulted in poor meshing and points of high stress that indicate failure. I also tried axisymmetric 2d study with no penetration as well and it worked fine with FOS just a bit smaller than expected in project, but a understant that this study is not very accurate. Now i am trying to remove the extruded threads and work only with smoth surfaces, therefore i need to change the study connections between part for the simmulation to work. I understand that bolt conectors would work fine for the female parts, but i dont understand how to set a simmilar connection for the male threaded part. Can anyone help me with that? My simmulation is a pressure study of a aquatubular boiler casing with flat threaded heads as male parts, for a academic project.
how to sync two circle example:- one circle dia75mm and secound circle dia1000mm dia1000mm (1000mm-100mm=900mm) so change dia 75mm change (75mm+100=175mm) mins i one circle dia minuse so secound dia pluse is value how create बहुत बढ़िया पर मुझे ऐसा काम कुछ इस तरीके से करना हो तो कैसे करे कृपया बताये जैसे के एक circle 75mm dia का हे और दूसरा circle 1000mm dia का हे अगर में इन दोनों में से किसी की भी साइज़ बदलता हु तो वो एक दुसरे में pluse minus खुद्ब्खुद हो जाये जैसे के अगर में 75 mm dia में 25 mm जोड़ता हु तो वो dia 100mm हो गया पर जो दूसरा dia जो 1000 mm का हे वो 975mm खुद्ब्खुद हो जाये बस ऐसे कोई भी एक dia अगर pluse होता हे तो दूसरा dia खुद्ब्खुद minuse हो जाना चाहिए और कोई भी एक dia minuse होता हे तो दूसरा dia खुद्ब्खुद pluse हो जाना चाहिए हा पर जितना हम pluse या minuse करते हे उतना ही value एक दुसरे dia में pluse minuse होना चाहिए कृपया करके ये बताये ये कैसे हो सकता हे solidwork में ?
To calculate the stresses on a bolt the real bolt geometry is needed, i.e. the CAD part of the bolt, which leads in a highly complex simulation. If the bolt connector is used, as described in the video, no stresses are calculated for the bolt, since a virtual model is used in the analysis. However, a pass or fail criterion is established internally by the software and it informs you whether your bolt connector is strong enough to withstand the external loads (axial, shear, bending).
wow, i've always been in need for such deep tutorials. THANK YOU!
Thank you sir.
Hi sir, what type of contact set of 2 part in this situation
How do I properly simmulate two connected threaded parts where both male and female parts are important in the analisys? I tried running a 3d static study using extruded threads modeled with the swept boss and cut features with helix path and ISO metric screw thread profile and no penetration connection between parts. This study resulted in poor meshing and points of high stress that indicate failure. I also tried axisymmetric 2d study with no penetration as well and it worked fine with FOS just a bit smaller than expected in project, but a understant that this study is not very accurate.
Now i am trying to remove the extruded threads and work only with smoth surfaces, therefore i need to change the study connections between part for the simmulation to work. I understand that bolt conectors would work fine for the female parts, but i dont understand how to set a simmilar connection for the male threaded part. Can anyone help me with that?
My simmulation is a pressure study of a aquatubular boiler casing with flat threaded heads as male parts, for a academic project.
how to sync two circle example:-
one circle dia75mm and secound circle dia1000mm
dia1000mm (1000mm-100mm=900mm) so change
dia 75mm change (75mm+100=175mm)
mins i one circle dia minuse so secound dia pluse is value
how create
बहुत बढ़िया पर मुझे ऐसा काम कुछ इस तरीके से करना हो तो कैसे करे कृपया बताये
जैसे के एक circle 75mm dia का हे और दूसरा circle 1000mm dia का हे
अगर में इन दोनों में से किसी की भी साइज़ बदलता हु तो वो एक दुसरे में pluse minus खुद्ब्खुद हो जाये
जैसे के अगर में 75 mm dia में 25 mm जोड़ता हु तो वो dia 100mm हो गया पर जो दूसरा dia जो 1000 mm का हे वो 975mm खुद्ब्खुद हो जाये
बस ऐसे कोई भी एक dia अगर pluse होता हे तो दूसरा dia खुद्ब्खुद minuse हो जाना चाहिए
और कोई भी एक dia minuse होता हे तो दूसरा dia खुद्ब्खुद pluse हो जाना चाहिए
हा पर जितना हम pluse या minuse करते हे उतना ही value एक दुसरे dia में pluse minuse होना चाहिए
कृपया करके ये बताये ये कैसे हो सकता हे solidwork में ?
Thanks for video.
How to automatically(in solidworks) calculate stresses in the bolts?
For example in ansys or creo simulate such a possibility.
To calculate the stresses on a bolt the real bolt geometry is needed, i.e. the CAD part of the bolt, which leads in a highly complex simulation.
If the bolt connector is used, as described in the video, no stresses are calculated for the bolt, since a virtual model is used in the analysis.
However, a pass or fail criterion is established internally by the software and it informs you whether your bolt connector is strong enough to withstand the external loads (axial, shear, bending).