TPLINK CPE210 / 220/ 510 / 610 Access Point and Client Complete Setup
HTML-код
- Опубликовано: 16 июл 2021
- #AccessPoint
#TPLink
If you find this video helpful,
Donation accepted at any amount.
GCASH 09167555337
You may want to have internet access for your nearby farm house to monitor CCTV, or control SMART SWITCH for generator or equipment, refill water for pets, or enjoy browsing while you're with your work away from home where fiber line is not available. Access Point answer this. So here's the simple and complete set-up and configuration. Remember to attach Router at the CLIENT CPE for WIFI Access..
Needed equipment:
2PCS pair
TPLINK CPE210 or CPE510
2PCS CAT6 OUTDOOR LAN CABLE needed to connect adapter to CPE
2PCS INDOOR CAT6 LAN CABLE needed to connect router to adapter.
TAKE NOTE: Router must be attached at the CLIENT CPE Power Adapter LAN PORT to enjoy browsing the internet
CPE210 Range tested: Best Performance if less that 1000m distance from the Access Point
If distance is more than 1km, it is better to use CPE510
You cannot use CPE210 and match with CPE510
You must use same frequency CPE, means if you use CPE210 as Access Point, then your Client must be CPE210 
Хобби
the best explanation thank you .
This was a great video to follow. My distance is just under 100 metres, but your video was by far the easiest to follow.
This was a life saver. Went seamlessly until I forgot a password at the very end. I got back on track with client, and all panned out. THANK YOU!!!
Thank you! Id had trouble with these for 3years. And now its finally working 😍
Thanks, no one else said to change the Client computer’s IP back to automatic
Laking tipid dahil dito naipasa ko ang internet 3km away.. Salamat
perfect video for cpe setup from A to Z
Superb, Thanks buddy... Very easy setps I have done my work by your tutorial...
simply the best by far thanks
Made life easy, great assist 👍
Thanks, best ever!
Thanks sir very helpful video
Muchas gracias, perfecto
Question is it possible to make 2 separate nanostation but all are in one location broadcast one Access point as if it was one nanostation?
thanks so much great job
thank you very much "CoolRider"..I use wireless TP-Link CPE210,,speed until 300Mbps it's very good 👍
Pls do visit my channel watch videos and ads to support me if you have time. Thank you in advance
Thank you bro
Hello,
Does it support multiple subnets?
is this an omni directional or directional connectivity
Thank you
Does this work for 220 bridges
Thank you so much for a very easy to follow video. I have MacBook and use MacOs. I have a couple questions: Both devices are configured and set up, but there is no internet connection between them. Where have I done wrong? Does the device have to be connected by cable every time a change needs to be made, or is it possible to do it online without a cable? Answer will be appreciated.
You need to connect AP(the 1st CPE configured in the video)to your ISP router. Then the last (client) CPE connect to your new router this will be the one to distribute internet
Great job
thankyou natapos ko din yung proj ko salamat po
Enjoy po..
Anyone know why it’s limited to 100 down despite using Cat 6 cables and having 700+ down from the modem?
Thx so much
Perfect
Hello! nice video ... I bought it after seeing you .. but a question: on the instructions that serve the grounding for the antenna .. did I understand correctly? a good shielded ethernet cable is not enough? !!
You may add grounding wire thats theoretically effective. But lightning wont spare anything if it will directly hit by it. Tried once my cpe directly hit by lightning, both cpe and router dead instantly. To sum up, grounding not that really effective.
Hi. To test alignment / signal strength when the Client and the AP are up so high did you need to have a long cable to the CPE or were you connected to the CPE via wifi?
you can use your phone once CPE is connected to the router. just manually set ip addfess of your phone
Does the first unit need to be physically connected to the router of my ISP? Let us say my ISP router is downstairs and the unit is upstairs. Can't they communicate wireless? I would need a long cable and holes in the walls
It cannot communicate wirelessly if the setup is like in the video. You need to connect router via lan cable.
@@iceicepogi Thank you
Darn wondering why my Access Point isnt showing in the Client Configuration part... hmmm
Hello, nice video! I wonder - I need help with my setup. Is this correct? Internetmodem -> router -> CPE210 access point -> CPE210 client -> Ubiquiti LR Access point -> Wifi connection to my computer, phone, appleTV. The router where the internet connection is could route the connection through this setup?
I want to share internet from one house to another house 500 m away, not only have one connection but multiple? Or do I need a router to create new ip-adress in the distant location and have that connected in between? internetmodem -> router -> CPE210 access point -> CPE210 client -> router - > Ubiquiti LR Access point -> wife connection to devices?
DHCP SHOULD BE ON OR NOT?
this may be a stupid question but can i connect wirelessly to the Client (eg. via a wireless camera) or do I need another router connected via ethernet cable to the client.
If you set as AP then check configuration of your camera if it can detect wifi..
I set it up via another router connected to the client I'm using the 710 5G version and have some devices that will only take 2.4. I could never find the client as a wifi network only the AP one but seems CoolRider is possibly suggesting you can have an AP to AP configuration?
I recently installed cpe210 AP and client but internet dropped completely frequently even if Tx and RX signal showing. Can you please help me?
Make sure of the line of sight
Thank you❤ . What is the provider's speed and the customer's speed up to 1km?
You can get same speed. Thats very short distance
I have one TP-link Cpe 510 . in client mode it is possible to connect to any wifi network or only to another tp-link cpe 510 ?
Yes. It is better if you pair it with the same CPE. Ordinary wifi function well with wifi gadgets. CPE is created to pair with CPE. It is better if you have another CPE. All you need to do is to configure AP mode so your client can work with it..
i think if u comnect ur cpe to another wifi other than another cpe's u won't get the long distance i will be used as a wifi adapter but i should have some good range
Can the receiver unit then connected to wifi router so that at the receiver house can get wireless Internet?
Yes you can connect to wifi router (client or known as reciever) as intended function. Just make sure that the AP is connected too to the main isp router
The Best ang explanation mo sir. Thank you. How about sa client na router sir Kung cpe510 gagamitin need po ba na 5g yung router?
Kahit 2.4ghz or dual 2.4 / 5ghz pwde
Sir after finishing configuring client cpe can i disconnected the lan line from pc???
Ans me please
I want to learn how to setup this device with pc and phone......
Yes disconnect it, then connect AP LAN to Router that is connected to the internet. Connect LAN Client CPE to router then enjoy the internet..
I have 210 and UBNT loco m2. 210 is a AP and loco M2 is client. But i am having a problem to connect AP. From client side i can see AP in. Site survey but I am not able to connect it. Please advise
Make sure they have the same frequency. 210 is 2.4ghz
Do I require internet connection in the laptop for configuration?
It is not required since you only configure the two device to exchange data with each other. Once done then you can connect the internet to the AP
Hi, I'm facing the issue of "failure to get data"
Have you any idea about it?
Make sure ap and client have good line of sight
I did all the steps and it worked. Thank you. Just a question please, the distance separating the two devices is approximately 400 meters. The signal he picked up is 50%. Is it good or should I try to answer 70 or 80%?
At 400m you should get full signal bar if no objects in line of sight. Check your line of sight between your cpe again..
If I connect the client to a router do I need to reconfigure the client? or no need?
Here's diagram.. Configure AP CPE, Configure Client CPE, Connect router.. Configuration is once only..
I want to have extended wifi to my garage, I have 2 of cpe210, how I need configure it to have extendef wifi? Can it work if first cpe210 i config like AP, second one config as repeater, and from repeater I can connect wifi?
You should configure as AP and Client as shown in this video. You need router in Client CPE.
@@iceicepogi so from client I must have LAN to router? Because I have router In my house, garage is 50 meeters from house, wifi to weak, so I need connect thes two cpe as in video, one cpe210 connectet to my main router in house and i install it outside house wall with lan cabel, then second cpe client i install on garage wall outside, then from client cpe i need conned LAN cabel to SECOND router in my garage? And from this router i can have wifi, do i understood right?
@@edvinas4072 you got it right!
funguje 🙂👍
Hello sir ung pnkta mong speedtest ano jto during setup ba or nung nakasetup n s malayo ung client ?
Nung malayo na sir. Basta maganda signal quality nya, mabilis ang speed..
only three lights lighting in client cpe what to do
Re align and monitor connection signal
@@iceicepogi re align the antenna or what to realign
Good day sir, is this set up compatible for omada piso wifi voucher type?
Yes fully compatibe with omada and eap.
Thank you po sir. Sa client side po ay need pa ba maglagay ng EAP for access point or hindi na po?
@@freefree8047 Yes need po maglagay ng eap client side para sya ang mag distribute ng wifi signal. I think parang ganito po sya: Client Cpe510-Router-Omada Controller-Eap
Hi! Pwede ba to CPE510 as AP then 210 for client?
Di pwde sir. Dapat parehas sila ng band. 2.4ghz kasi ang 210. Tas 5ghz ang 510.
sir kung naka ap mode ang base station pwede ba madaming client na cpe kumonek?
Pwede sir..
Sir possible po ba iconnect ang cpe510 sa cpe605 for p2p? 500m lang po distance ng dalawa..
Pwede pwde. 500m napakalapit lang
Boss pede ko ba i hide ssid ni AP,. May 10 stations na connected. Hindi ba maapektuhan mga ito sir pag naghide ako ssid ni AP
Pwde mo i hide AP
Is it compatible with starlink?
It should be. Because all routers are standardized to adapt other equipment such as these cpe to work together.
hi can i get wifi from the access point
Yes you can connect to it
If the distance is just 300 m can just use one
Boss pwede pagawa tutorial paano mag config ng Multi AP isang EAP 110 at CPE210. TY
Eap110 pwede multi AP sya. Pati CPE210 pwde din multi AP
boss hindi ba maglalagay ng distance settings sa sender/Ap? naka zero lang kasi DISTANCE SETTINGS. samantala sa RECEIVER/client nilagyan mo ng 1Km.
Automatic yan sir basta nag bind na yang dalawa..
I follow all your step,but when I connect the access point to ISP,it's still can't internet
What model do you use for AP and Client?
@@iceicepogi CPE210
napunta ako dito dahil sa shopee..hahaha
Yes shopee din ako kumuha
@@iceicepogi ilang kilometers aabot sir
@@ByahingJoPH CPE210 medyo hirap na sa 1km nung nag test ako marami matataas na kahoy, i think kulang sa height ang pole ko. Pag lampas 1km mas maganda CPE510 kana mas reliable, kunti lang naman dagdag sa presyo
Good im trying to configure cpe510 in AP ROUTER mode, pero pag mag click na ako sa AP ROUTER mode may warning message na ganito
"the status of Port0 will change to WAN, and the management access will be disabled on this port.
If you want to managr the cpe device through Port0, go to MANAGEMENT>Web server to configure the Remote Login IP Address"
Paano ito ma solve, mas preferred ko kasi AP ROUTER mode to control download and upload speed ng client
Pa send screenshot Messenger sir sa E-Link Rosario para ma check ko..
idol paano lagyan ng pisowifi ang receiver side? Ganyan ksi na setup gusto ko pero dagdagan ko vendo
Gamitan lang ng router tas ikabit mo na sa piso wifi client mo
Kung mga 150m lang walang line of sight ano pwedeng gamitin?
Mas maganda mag FOC ka na lang pag wala LOS.
Paano po setup cpe210 sa vlan? Di ko po masave yung vlan settings sa network vlan management
May i know kung paaano hardware setup nyo sir? Haven't tried aa vlan. Although may vlan ako nakita sa portal nya, try nyo lang tignan.
All I would suggest is that you make backups of both the Access Point & Client configurations. Otherwise one of the most concise videos ... Thank you!
yes all my cpe have thier own config file.. Pretty good idea
Sir okay lang ba iisa lang yung CPE? kasi medyo kapos pa sa budget. I mean, Modem (Converge) > CPE (AP) > Router (tenda). Bali yung tenda na yung mag rereceive and nasa 250m po yung layo.
Pwede naman siguro kung kaya ng signal sir try nyo po..
Hi .. Pareho lang ba config nito sa CPE605?
Yes same sila
what is best signal rate please sir
80 and up
lods san ka sa papaya
Papaya?
Boss pwd ba cp mag set up
Di pwde.
@@iceicepogi kahit anung tplink na antena?
@@WarikTV dapat match frequency. 2.4 ghz di pwde sa 5ghz
Haha y lame sound rs