I just installed these lights in my 2020 F150 XLT and added the switchback LED. Super happy with them! Pro tip: Test the switchback LED's BEFORE you install them in the light housings. You have a 50/50 chance that you will need to reverse the LED bulb in the connector to make it work. It's a 10-second fix if you haven't put the housings back on the truck. If you have, you now have a vocabulary expansion project and another 15 minutes of work.
If you're planning to install these yourself you should read this review since I already went through it. First off I'm very pleased with the headlights the DRLs are crisp and the brightness of low and high beams are a significant upgrade. Morimoto is top notch quality and with the 5 year warranty you get what you pay for. As far as the installatiRead more about review stating Better than OEM, installation video misleading for 2020on, the video was misleading in some aspects. I have a 2020 F-150 Lariat and do NOT try to remove the fender flares the way it shows in the video. the clips are made differently and if you attempt to take it off like the video you'll break the clips. I broke one of mine until I realized the clips were positioned different on my truck compared to the video. The fender flares need to be pulled up and out they don't just pry off with ease like in the video. Second, when removing the grill the video fails to mention that there are 2 additional bolts underneath the grill, one on each side. I was wondering why it was so difficult to get the grill to come off until I realized there are 2 more bolts. Again these are differences that are for the 2020 F-150s. I'm unsure what year they started to make these slightly different manufacturing changes. Maybe the 2018-2020 trucks. When it came down to replacing the blinker bulbs is where I ran into most trouble. I bought the exact GTR lighting LED blinker bulbs shown in the installation video because I was not planning to spend $900 on new LED headlights to have halogen blinker bulbs. During the installation process I found out the stock blinker bulb housing would not fit in the morimotos socket as shown in the video. Furthermore the blinker bulb housing that came with the morimotos did not fit with the GTR LED bulbs. After reading some forums online, apparently if you have red rubber seals on your stock housings it has 3 plastic secure tabs and if you have blue seals on the stock housing it has 4 secure tabs. The stock housing with 4 tabs is the one that fits inside the morimotos. My truck of course had the red seal with 3 tabs. I had the front end of the truck apart and I couldn't afford to wait for the right parts to come in so I had to improvise. If you're handy with a dremel you could easily shave off part of the socket where the housing clicks into. I measured it by eye where the tabs would sit and it ended up clicking in place. I also tend to overengineer things so I put a little bead of all weather silicone to keep the housing from popping out of the socket just in case. Let it set for couple hours and it was pretty secure. Basically if you want the LED blinkers make sure you have the correct blinker bulb housings. I also used a dremel to make a notch on the fuse box cover and a notch on the fuse box itself. I find that if you don't make a little notch, the wire that runs to the DRLs gets pinched too much. Overall I made everything work and it all looks great. The installation was fairly easy for the average person that does any other car maintenance. Very happy with the LEDs the visibility at night is way better than stock halogens and the appearance just looks more sharp. In the dark the headlights look similar to the older raptor style which I like. I also don't know the hype with the switchback LED blinker bulbs. The amber LEDs compliments the white low and high beam nicely and looks better. Headlight Revolution should make an updated video and be specific with parts when purchasing headlights for 2020 trucks. Figured it all out during the installation which is why I wrote this in depth review. Hope this helps.
I have a 2020 f-150 xlt and all the crazy comments about the turn signals bulbs not fitting is making me nervous about the install. I know my wife wants the white turn signal switchback. The morimoto hybrids are sitting in my garage waiting to get installed but I’ve been reading the horror stories of bulbs not fitting . Still unsure of which turn signal bulbs I should purchase.🤦♂️
Caution! Getting the trim piece out from under the headlights on a 2020 does not use this method! Only one screw in each wheel well. The fender flare is attached to the trim piece in two spots with clips that impossible to remove by pulling as shown in this video. They will break if you pry on the flare. I believe the whole flare needs to be removed to separate the under headlight trim from the flare. Then, you can decouple the flare from the trim piece.
Ordered the led turn signal you recommended im the video but it does not fit! It slides in but is too loose and doesn't click in. It will fall right out. Is there something I'm missing?
@@HeadlightRevolution Figured it out. The socket that comes with these headlights does NOT fit that bulb. I had to reuse the socket from my old housing (which I now realize is what you show in the video), but I have a 2018. A few people w/ 2019/2020 say their OEM socket doesn't fit that new housing. Also I really agree with other comments on here you should update both Morimoto videos for the two 8mm bolts at the bottom of the grill. Took me awhile to find those and figure out why my grill wasn't coming out as easily as in the video. Otherwise, great walkthrough of the process. My install went relatively smoothly.
@@ak-zw8jv I have a '19 and my OEM socket wouldn't fit the new housing. My OEM socket has 3 tabs, while the new housing has 4 tab openings. Luckily I had bought the recommended GTR amber bulbs and it fit in the new socket, and then of course fit well in the new housing. I did have a brief moment of panic however, as I thought I had taken everything apart for nothing lol.
Thanks for the great install video. One question in regards to your truck, where did you get the side door stripes from? They appear to be black reflective which looks great!
What's the difference between ck and non ck. I have the exact truck and just ordered the exact morimoto xb hybrids. Not sure what turn signal switchback to order. Thxxx
Its how they are grounded, this link will help you out!. blog.headlightrevolution.com/do-i-have-ck-or-standard-wiring?gclid=CjwKCAjwrPCGBhALEiwAUl9X00iughHD6vNEdcI1gQI_JwlsF11Kg0VI4KAAfGHIAkbIv6fP1RRDshoCljQQAvD_BwE
Did you buy the XBs or XB Hybrids? Hybrid headlights are not compatible with OEM LED trucks 😔 Shoot us an email if you need help - sales@headlightrevolution.com
You will need the 7443 Carbide 2.0 Standard Wiring bulbs, that part number is GTR.LED590 for the all amber versions! I have linked that for you here: www.headlightrevolution.com/7440-7443-gtr-lighting-carbide-bulbs-LED.BUL.7443.CAR2_2?quantity=1
Most of the time they should come preset for the vehicle, but sometimes you will need to adjust them when you install them. To do this, it is super simple, you will just loosen or tighten the adjuster screws on the back of the headlight housings, and that will move the headlight up, down, left, and right! If you have any other questions, let us know!
Having issues with the led running light staying on well after truck is turned off. Sometimes stays on as long as 10min. Do you suggest a different fuse location?
Fuse 36 will stay hot in some specific models of that truck, if this is the case you will want to swap that fuse tap harness over to either fuse 35 or fuse 37 so that the lights do not stay on so long. Let me know if you need anything else!
I had the same problem and sent an email to Headlight Revolution. They replied with fuse spot #16 (10a fuse) and it worked as expected. The drl’s will turn off when the ignition is off.
I want to know when are you going to make a video for the XB lights for the 2015-2018 Yukon Denali I seen the clip of the 2021 lights on a 2018 or 2019 Yukon
I have a set of the original XBs and one of my biggest pet peeves is the top LED bar on the DRL is not as bright as the side and bottom ones. Are all three equally bright on these new ones?
Yes, the top LED bar for the DRL should be the same brightness as the side and the bottom. Please shoot us an email, and we can get this taken care of for you! Sales@HeadlightRevolution.com
Here's a Link: headlightrevolution.com/2018-ford-f-150-led-front-turn-signals/ You'll want to decide if you want a solid Amber/Amber Turn Signal, or if you want the Switchback White/Amber Signal, totally up to you!
Two questions. First, can you add your part numbers for the LED Switchback turn signal bulbs for the 18 F150 (Pretty Sure it is LED.BUL.7443.CAR2.CK) But want to make sure Second, does the DRL fuse tap harness come with the lights, or does it need to be ordered separately? If separate....part number please.... Great looking lights !!! Will be ordering soon!
The DRL fuse tap comes with the lights, Yes. This is the turn signal bulb you need: headlightrevolution.com/gtr-lighting-carbide-series-2-0-canbus-7440-7443-led-bulbs-standard-style/
No. I just ran into that same issue with mine after being installed for three days. I unplugged the DLR fuse tap and replaced the original fuse. The strip still works but it doesn't have the brighter setting when the lights are off. I'm going to find another slot to use and see if they work properly.
I contacted the dealer and they said the led strip will stay on constantly as the daytime running light from now on. I think its a stupid idea. Let me know what fuse you happen to try out.
@@richf2834 I tried a couple of different slots and neither worked. I found the same issue as we are having on F150forum.com and the guy tried all kinds of things, nothing was working. Then he noticed that he had condensation in his aftermarket tail lights and when he replace them back to stock the DRL strips were working correctly from then on. I installed aftermarket ANZO tail lights at the same time that I installed my headlights. I noticed in the instructions on Morimoto's website that it states that if the vehicle is equipped with anything besides OEM tail lights(full assemblies, LED bulbs, etc.) that the resistors can cause an impedance problem with the OEM settings and that this is not a fault of the headlights. So I just unplugged the DRL fuse tap and I'm not running them until I can come across a solution. It sucks but it is what it is for now. I'll keep you posted if I can find anything.
@@richf2834 Ialso found some others that are having the same issue with the Alpha Rex headlights and one person said that they used fuse slot #18 and everything is working normally. I may just give that a try.
We’ll do more pictures on our social media, but it’ll be awhile before we update the video. We usually wait for the product to change or evolve before making a new video.
I'm thinking about getting these but I have the raptor style lights on my 2018 truck that connect into the amber/turn signal bulb with a Y connector. Could I still use that with these headlights or do I have to splice them in?
@@HeadlightRevolution yes they said it would void the warranty, the stock headlights (are unsafe). I was told I could upgrade them with something as Sylvania Silverultra lights
If you leave the factory turn signal bulb...would the middle light be amber ...and is it on always with the head lights....the canbus bulb is a switch back? But with the drl only that center signal bulbs would not be illuminated correct?
Yes it would be amber just like how your factory headlights are set up. We show a canbus compatible switchback bulb in this headlight. The center bulb will not be illuminated when DRL is on.
Why is the lux output from the original video at 630 lux( with the quad morimoto headlights) and this video 230 lux. Something seems weird with that? I'm getting these as replacements due to insurance only covering up to 1k
When comparing lux numbers, they need to be from the same test as lux numbers will vary. The amount of light in the room and distance from the light to the lux meter will affect the lux readings. Just a 5 inch distance between the light and the lux meter will result in a different lux reading.
I beleive that those came on that vehicle with that model F-150, but I am not sure. You will have to get those somewhere else, as that is not a product we carry or have information on. Sorry about that!
It depends on what bulb you go with for the turn signals. Since these are the Hybrid headlights, they come with incandescent bulbs that will only be amber. You can upgrade to the GTR Lighting Carbide 2.0 switch back bulbs, which will run white and then flash amber though! headlightrevolution.com/2018-ford-f-150-led-front-turn-signals/
Headlight Revolution ok thanks. Does the low beam come on during the day on these? My factory 2020 halogens the low beam is the running light. I would prefer if it was just the led ring on these. Regardless I will be ordering a set when there in stock
Headlight Revolution I just realized I missed the sale! Anyway you can extend it because these are what I’m looking for but the 20% off made it affordable?
I have 2020 F-150 XLT and was wondering if there was anything else in addition to the 7443 bulbs I have to buy to install these? I heard people complaining that the old sockets don’t fit new housing so does Morimoto provide the new sockets?
We had an issue right at the beginning with the Hybrid Superduty models, that has been resolved so all you will need is the pair of turn signal bulbs!🤘
I just installed these today the oem sockets still don't fit. I had to purchase 7444na bulbs to install into morimotos... They don't fit to loose, had to try to bend to connectors for more snug fit and super glue (rigged it up) to work. but just found out to can purchase 9E5Z-13411 B sockets and they will fit perfectly. So just in case you haven't purchased our deciding too.
@@brandoneyring5713 I’ve got a 2020 my set of lights are waiting in my garage but all this bull shit about problems with the socket and bulb sizes not fitting needs to be addressed by headlight revolution. Very bad business to mis-lead people
Just did the install yesterday on my '19 F-150. Thanks for the instructional video, it definitely helped. All went well, just had a little trouble getting the grill out at first, but it wasn't too bad. Went with the recommended LED turn signal bulbs (GTR) and they do look quite awesome. I ended up making a small notch in the fuse box to run the fuse tap wire through. I actually made a quick time lapse of my install just for the heck of it. ruclips.net/video/vcNfszwhJRY/видео.html
Right on my man! Glad you were able to get them figured out! I actually had to notch the fuse box on my personal vehicle as well, wish I didn't have to but it helps so much when you do that!👍 Thanks for linking your video!😃
You would need a pair of the Armor series 7443 bulbs, and a pair of resistors! I have linked both of them for you, and if you have any other questions, let me know! LED Bulbs: headlightrevolution.com/gtr-lighting-armor-series-7440-7443-led-bulbs/ Turn Signal Resistors: headlightrevolution.com/gtr-lighting-50-watt-6-ohm-gold-style-resistors-for-custom-installation/
I am not sure if that is in the works, haven't heard of that happening as of right now. We will of course keep you posted if we get anything new like that!
I just installed these lights in my 2020 F150 XLT and added the switchback LED. Super happy with them! Pro tip: Test the switchback LED's BEFORE you install them in the light housings. You have a 50/50 chance that you will need to reverse the LED bulb in the connector to make it work. It's a 10-second fix if you haven't put the housings back on the truck. If you have, you now have a vocabulary expansion project and another 15 minutes of work.
Reverse polarity is something to watch out for, it does apply to almost all of those LED bulbs! Thanks for commenting and for the support!🙏
Headlight Revolution did you have any fitment issues? I’ve read in forums that ford changed the Turn signal size in late 2018
Brenny627 The fitment was perfect for me. No issues whatsoever on the headlights or the switchback LED’s. Couldn’t be happier with the whole setup!
You never need resistors. With FORSCan and a OBD adapter you can program it the hyper flash out.
While you certainly can use FORSCan, most people do not have the ability to use it.
If you're planning to install these yourself you should read this review since I already went through it. First off I'm very pleased with the headlights the DRLs are crisp and the brightness of low and high beams are a significant upgrade. Morimoto is top notch quality and with the 5 year warranty you get what you pay for. As far as the installatiRead more about review stating Better than OEM, installation video misleading for 2020on, the video was misleading in some aspects. I have a 2020 F-150 Lariat and do NOT try to remove the fender flares the way it shows in the video. the clips are made differently and if you attempt to take it off like the video you'll break the clips. I broke one of mine until I realized the clips were positioned different on my truck compared to the video. The fender flares need to be pulled up and out they don't just pry off with ease like in the video. Second, when removing the grill the video fails to mention that there are 2 additional bolts underneath the grill, one on each side. I was wondering why it was so difficult to get the grill to come off until I realized there are 2 more bolts. Again these are differences that are for the 2020 F-150s. I'm unsure what year they started to make these slightly different manufacturing changes. Maybe the 2018-2020 trucks. When it came down to replacing the blinker bulbs is where I ran into most trouble. I bought the exact GTR lighting LED blinker bulbs shown in the installation video because I was not planning to spend $900 on new LED headlights to have halogen blinker bulbs. During the installation process I found out the stock blinker bulb housing would not fit in the morimotos socket as shown in the video. Furthermore the blinker bulb housing that came with the morimotos did not fit with the GTR LED bulbs. After reading some forums online, apparently if you have red rubber seals on your stock housings it has 3 plastic secure tabs and if you have blue seals on the stock housing it has 4 secure tabs. The stock housing with 4 tabs is the one that fits inside the morimotos. My truck of course had the red seal with 3 tabs. I had the front end of the truck apart and I couldn't afford to wait for the right parts to come in so I had to improvise. If you're handy with a dremel you could easily shave off part of the socket where the housing clicks into. I measured it by eye where the tabs would sit and it ended up clicking in place. I also tend to overengineer things so I put a little bead of all weather silicone to keep the housing from popping out of the socket just in case. Let it set for couple hours and it was pretty secure. Basically if you want the LED blinkers make sure you have the correct blinker bulb housings. I also used a dremel to make a notch on the fuse box cover and a notch on the fuse box itself. I find that if you don't make a little notch, the wire that runs to the DRLs gets pinched too much. Overall I made everything work and it all looks great. The installation was fairly easy for the average person that does any other car maintenance. Very happy with the LEDs the visibility at night is way better than stock halogens and the appearance just looks more sharp. In the dark the headlights look similar to the older raptor style which I like. I also don't know the hype with the switchback LED blinker bulbs. The amber LEDs compliments the white low and high beam nicely and looks better. Headlight Revolution should make an updated video and be specific with parts when purchasing headlights for 2020 trucks. Figured it all out during the installation which is why I wrote this in depth review. Hope this helps.
Thanks for the review, Frank!
For those that have the 2019 the 7443 didn't work for me. I ended up getting the 7444NA Sylvania (non LED).
Thanks for the info!
Wow 🤩 .. that truck look 👀 so so good! Specially watching it on 90in. HDTV 👍
I’m glad you like it!
I have a 2020 f-150 xlt and all the crazy comments about the turn signals bulbs not fitting is making me nervous about the install. I know my wife wants the white turn signal switchback. The morimoto hybrids are sitting in my garage waiting to get installed but I’ve been reading the horror stories of bulbs not fitting . Still unsure of which turn signal bulbs I should purchase.🤦♂️
Crickets 🦗 week later @headlightrevolution
Hey did the install work out for you man?
Caution! Getting the trim piece out from under the headlights on a 2020 does not use this method! Only one screw in each wheel well. The fender flare is attached to the trim piece in two spots with clips that impossible to remove by pulling as shown in this video. They will break if you pry on the flare. I believe the whole flare needs to be removed to separate the under headlight trim from the flare. Then, you can decouple the flare from the trim piece.
Good tip! THanks!
With headlights ON and when activating the turn signal, do the headlights deactivate on that particular side?
They do not, They remain on like normal.
Ordered the led turn signal you recommended im the video but it does not fit! It slides in but is too loose and doesn't click in. It will fall right out. Is there something I'm missing?
This could be due to a few things. Shoot us an email, and we'll get this fixed right away!
Sales@HeadlightRevolution.com
@@HeadlightRevolution Figured it out. The socket that comes with these headlights does NOT fit that bulb. I had to reuse the socket from my old housing (which I now realize is what you show in the video), but I have a 2018. A few people w/ 2019/2020 say their OEM socket doesn't fit that new housing. Also I really agree with other comments on here you should update both Morimoto videos for the two 8mm bolts at the bottom of the grill. Took me awhile to find those and figure out why my grill wasn't coming out as easily as in the video. Otherwise, great walkthrough of the process. My install went relatively smoothly.
@@ak-zw8jv I have a '19 and my OEM socket wouldn't fit the new housing. My OEM socket has 3 tabs, while the new housing has 4 tab openings. Luckily I had bought the recommended GTR amber bulbs and it fit in the new socket, and then of course fit well in the new housing. I did have a brief moment of panic however, as I thought I had taken everything apart for nothing lol.
Thank you.
Great video thanks!
Thank you!
Thanks for the great install video. One question in regards to your truck, where did you get the side door stripes from? They appear to be black reflective which looks great!
Chris is no longer with us so unfortunately I don't have a way to ask him. Sorry!
@Joshua Henry - its available on the Special Edition trims of the F150
What's the difference between ck and non ck. I have the exact truck and just ordered the exact morimoto xb hybrids. Not sure what turn signal switchback to order. Thxxx
Its how they are grounded, this link will help you out!.
blog.headlightrevolution.com/do-i-have-ck-or-standard-wiring?gclid=CjwKCAjwrPCGBhALEiwAUl9X00iughHD6vNEdcI1gQI_JwlsF11Kg0VI4KAAfGHIAkbIv6fP1RRDshoCljQQAvD_BwE
I just ordered these and my 2019 f150 stock led lights have different harness than these lights do….is there a harness I need to buy?
Did you buy the XBs or XB Hybrids? Hybrid headlights are not compatible with OEM LED trucks 😔 Shoot us an email if you need help - sales@headlightrevolution.com
@@HeadlightRevolution unfortunately I did not buy the correct ones. I purchased the hybrids. I didn’t buy them off here
So what is the specific part number for the LED switchbacks with no resistor for a 2020 F-150 lariat?
Following
You will need the 7443 Carbide 2.0 Standard Wiring bulbs, that part number is GTR.LED590 for the all amber versions! I have linked that for you here: www.headlightrevolution.com/7440-7443-gtr-lighting-carbide-bulbs-LED.BUL.7443.CAR2_2?quantity=1
@@HeadlightRevolution so by standard you mean the non CK version, correct?
This may be a stupid question, but do the lights need to be adjusted after they are installed, or do they come out of the box ready to go?
Most of the time they should come preset for the vehicle, but sometimes you will need to adjust them when you install them. To do this, it is super simple, you will just loosen or tighten the adjuster screws on the back of the headlight housings, and that will move the headlight up, down, left, and right! If you have any other questions, let us know!
@@HeadlightRevolution Thank you! I am going to order mine within the next couple of months! Talk to you all soon.
Not a problem, glad I could help with that! If you have any other questions or concerns, let us know and we will be happy to help! Have a good one!
Hi, how did you guys pop back in the fender flares, i cannot clip them back in especially the first clip, they are staying like sideburns pls help
Oh man that sucks did you get it fixed?
anyone know why they stay on for so long once you cut the truck off
What fuse can I tap becides #36? Trying to eliminate the drls staying on after the truck is off. TIA
Shoot us an email and we can assist you Sales@headlightrevolution.com
Having issues with the led running light staying on well after truck is turned off. Sometimes stays on as long as 10min. Do you suggest a different fuse location?
Fuse 36 will stay hot in some specific models of that truck, if this is the case you will want to swap that fuse tap harness over to either fuse 35 or fuse 37 so that the lights do not stay on so long. Let me know if you need anything else!
I had the same problem and sent an email to Headlight Revolution. They replied with fuse spot #16 (10a fuse) and it worked as expected. The drl’s will turn off when the ignition is off.
The title only mentions F150. Are they also a replacement for the halogen lamps in a 2019 F250?
This headlight does not fit the f250/f350, It’s only for the F150.
I want to know when are you going to make a video for the XB lights for the 2015-2018 Yukon Denali I seen the clip of the 2021 lights on a 2018 or 2019 Yukon
Soon!
I have a set of the original XBs and one of my biggest pet peeves is the top LED bar on the DRL is not as bright as the side and bottom ones. Are all three equally bright on these new ones?
Yes, the top LED bar for the DRL should be the same brightness as the side and the bottom. Please shoot us an email, and we can get this taken care of for you!
Sales@HeadlightRevolution.com
Hey I know this was a long time ago, but did you get it fixed?
What’s the link for the led turn signals. And do I pick amber or switchback?
Here's a Link: headlightrevolution.com/2018-ford-f-150-led-front-turn-signals/
You'll want to decide if you want a solid Amber/Amber Turn Signal, or if you want the Switchback White/Amber Signal, totally up to you!
Two questions.
First, can you add your part numbers for the LED Switchback turn signal bulbs for the 18 F150 (Pretty Sure it is LED.BUL.7443.CAR2.CK) But want to make sure
Second, does the DRL fuse tap harness come with the lights, or does it need to be ordered separately? If separate....part number please....
Great looking lights !!! Will be ordering soon!
The DRL fuse tap comes with the lights, Yes. This is the turn signal bulb you need: headlightrevolution.com/gtr-lighting-carbide-series-2-0-canbus-7440-7443-led-bulbs-standard-style/
I have a 2018 XLT is the Turn signal build CK or standard I hear mixed answers.
I installed mine and the led surround strip is on constantly even if the lights are turned off. Is this normal?
No. I just ran into that same issue with mine after being installed for three days. I unplugged the DLR fuse tap and replaced the original fuse. The strip still works but it doesn't have the brighter setting when the lights are off. I'm going to find another slot to use and see if they work properly.
I contacted the dealer and they said the led strip will stay on constantly as the daytime running light from now on. I think its a stupid idea. Let me know what fuse you happen to try out.
@@richf2834 I tried a couple of different slots and neither worked. I found the same issue as we are having on F150forum.com and the guy tried all kinds of things, nothing was working. Then he noticed that he had condensation in his aftermarket tail lights and when he replace them back to stock the DRL strips were working correctly from then on. I installed aftermarket ANZO tail lights at the same time that I installed my headlights. I noticed in the instructions on Morimoto's website that it states that if the vehicle is equipped with anything besides OEM tail lights(full assemblies, LED bulbs, etc.) that the resistors can cause an impedance problem with the OEM settings and that this is not a fault of the headlights. So I just unplugged the DRL fuse tap and I'm not running them until I can come across a solution. It sucks but it is what it is for now. I'll keep you posted if I can find anything.
@@richf2834 Ialso found some others that are having the same issue with the Alpha Rex headlights and one person said that they used fuse slot #18 and everything is working normally. I may just give that a try.
@@hdz12ez I will give it a try with # 18. But I do still have stock brake lights. I'm stumped. Time to just start trying different fuses. Thanks !
Will you guys be doing any more tests with these lights? And more pictures/ videos?
We’ll do more pictures on our social media, but it’ll be awhile before we update the video. We usually wait for the product to change or evolve before making a new video.
Headlight Revolution ok! Thanks for the fast reply! I’ll be looking out for those pictures
I'm thinking about getting these but I have the raptor style lights on my 2018 truck that connect into the amber/turn signal bulb with a Y connector. Could I still use that with these headlights or do I have to splice them in?
I'm honestly not sure on that one. I don't know of anyone with that setup yet. In theory, it should work just fine.
Are these full LED, or a projector with a LED bulb in it?
Thanks. Also if a buld, then what type of bulb are you using in the video?
Thanks again
These are a sealed LED headlight, They do not use bulbs at all.
Headlight Revolution what happens when it dies?
@@dojyr3130 Did their lack of response answer your question? 🤷♂️
@@HeadlightRevolution still waiting on a response to @Doja's question.
@@officeroinker440 they come with a 5 year warranty. Send them back and get new. Duhhhhhh
Hi, just purchased these headlights and want to upgrade to the GTR 2.0s. Do I order the CKs or non CKs? Thanks
Non-CK for this truck!
How can you find the switchback? On the sight it shows white amber or red?
Here are the turn signal bulbs that will fit these headlights:
headlightrevolution.com/2018-ford-f-150-led-front-turn-signals/
By switching out the housings and bulbs will this void any warranty? 2021 STX
I would call your dealership and ask.
@@HeadlightRevolution yes they said it would void the warranty, the stock headlights (are unsafe). I was told I could upgrade them with something as Sylvania Silverultra lights
Weird! It typically changes from dealership to dealership.
I've heard of customers, going TO the dealership and having them install them.
If you leave the factory turn signal bulb...would the middle light be amber ...and is it on always with the head lights....the canbus bulb is a switch back? But with the drl only that center signal bulbs would not be illuminated correct?
Yes it would be amber just like how your factory headlights are set up. We show a canbus compatible switchback bulb in this headlight. The center bulb will not be illuminated when DRL is on.
@@HeadlightRevolution do you have a link to that particular bulb...I couldn't find it on site
Sorry about that, Here you go! headlightrevolution.com/2018-ford-f-150-led-front-turn-signals/
@@HeadlightRevolution it says they come with resistors but in the video you said these are error free without resisitors?
It’s a mistake on the listing. These bulbs do not need resistors.
Forget resistors. Use FORScan to code it out. Super easy.
FORscan is really slick, Highly recommended.
Why is the lux output from the original video at 630 lux( with the quad morimoto headlights) and this video 230 lux. Something seems weird with that?
I'm getting these as replacements due to insurance only covering up to 1k
When comparing lux numbers, they need to be from the same test as lux numbers will vary. The amount of light in the room and distance from the light to the lux meter will affect the lux readings.
Just a 5 inch distance between the light and the lux meter will result in a different lux reading.
10-4
It was such a big swing. But that makes sense
Dammitt. I'm gonna have to order these. I'm not happy with my ebay specials. Lol.
I ordered these 6 weeks ago and it still shows shipment waiting under order status. Any indication as to when we’ll get these?
The Hybrid headlights are still on Pre-order. We're expecting to receive them and ship them right around the middle of June!
Great job,forgot one thing,disconnect the ground from your battery,then u work
Yes, you are right thanks
Is the amber side marker light LED or halogen?
For the Hybrid headlights, they are halogen. For the XB headlights, they are LED.
Great video! Looking to add the red Ford badge front and rear, any idea where I can pick them up?I need them shipped to Canada.
I beleive that those came on that vehicle with that model F-150, but I am not sure. You will have to get those somewhere else, as that is not a product we carry or have information on. Sorry about that!
@@HeadlightRevolution No worries, thanks for the reply!
Not a problem, have a good one!
I can send you a link for a company that custom paints them if you are still looking
@@davewilbur4686 That would be great thanks!
What bulb did you use? Non CK or CK?
You will want the Non-CK style bulbs! Let us know if you have any other questions, we are here to help!
I can’t find the led turning signal in your website
Here is exactly what you need: headlightrevolution.com/gtr-lighting-carbide-series-2-0-canbus-7440-7443-led-bulbs-standard-style/
Do these turn signals turn white when the signal goes off?
It depends on what bulb you go with for the turn signals. Since these are the Hybrid headlights, they come with incandescent bulbs that will only be amber. You can upgrade to the GTR Lighting Carbide 2.0 switch back bulbs, which will run white and then flash amber though!
headlightrevolution.com/2018-ford-f-150-led-front-turn-signals/
Headlight Revolution ok thanks. Does the low beam come on during the day on these? My factory 2020 halogens the low beam is the running light. I would prefer if it was just the led ring on these. Regardless I will be ordering a set when there in stock
The low beams will turn on with the DRL, yes. But you can disable the DRL's in the trucks settings so that doesn't happen.
Is there a discount code that we can use? I'm stuck between this and the Alpharex headlights.
Use code GARAGETIME to get a deal on these lights!
Headlight Revolution I just realized I missed the sale! Anyway you can extend it because these are what I’m looking for but the 20% off made it affordable?
I have 2020 F-150 XLT and was wondering if there was anything else in addition to the 7443 bulbs I have to buy to install these? I heard people complaining that the old sockets don’t fit new housing so does Morimoto provide the new sockets?
We had an issue right at the beginning with the Hybrid Superduty models, that has been resolved so all you will need is the pair of turn signal bulbs!🤘
@@HeadlightRevolution thank you for the reply!
Not a problem, let us know if you need anything else! Have a great day!
I just installed these today the oem sockets still don't fit. I had to purchase 7444na bulbs to install into morimotos... They don't fit to loose, had to try to bend to connectors for more snug fit and super glue (rigged it up) to work. but just found out to can purchase 9E5Z-13411 B sockets and they will fit perfectly. So just in case you haven't purchased our deciding too.
@@MD-eu7mx what year truck do you have?
Will these be made in a chrome finish?
I don't believe so, we haven't heard of any plans for a chrome version from Morimoto.
How can i buy it?
Check out the link in the description of this video!
Could you post the link to the LED bulbs?
This is what you need: headlightrevolution.com/gtr-lighting-carbide-series-2-0-canbus-7440-7443-led-bulbs-standard-style/
Excellent and in this video they are the switchback white/amber?
Yes they are! You’ll want to choose the switchback option.
Are these in stock yet?
When does your Garagetime sale end?
It’s ending April 3rd.
@@HeadlightRevolution Thanks for the Reply!
My order is being delayed until April 6th :(
Sorry about that, We’ve had some odd product delays due to Covid19 that are very unpredictable.
Sooo my original turn signal bulb, didn’t fit into the new morimoto headlight bulb? Anyone have this problem?
What year truck?
@@Bob-sp6fp 2019
@@brandoneyring5713 I’ve got a 2020 my set of lights are waiting in my garage but all this bull shit about problems with the socket and bulb sizes not fitting needs to be addressed by headlight revolution. Very bad business to mis-lead people
I’ve read one comment where a guy had to buy 9E5Z-13411B sockets to fit
@@brandoneyring5713 hope your not dead in the water
Does anyone know how much they cost. ?
These headlights are $800, and you can find them on our website!
headlightrevolution.com/ford-f150-18-20-morimoto-xb-hybrid-led-headlights/
Does anyone know how much they cost and is there a contract number ?
These headlights are $1,350, and you can find them on our website!
headlightrevolution.com/2018-ford-f-150-xb-led-headlights/
Did anyone else have the clips on the fender flares break on ya? I did. How come my shit never comes apart as easy as there’s?
Hate to hear that!
Just did the install yesterday on my '19 F-150. Thanks for the instructional video, it definitely helped. All went well, just had a little trouble getting the grill out at first, but it wasn't too bad. Went with the recommended LED turn signal bulbs (GTR) and they do look quite awesome. I ended up making a small notch in the fuse box to run the fuse tap wire through.
I actually made a quick time lapse of my install just for the heck of it. ruclips.net/video/vcNfszwhJRY/видео.html
Right on my man! Glad you were able to get them figured out! I actually had to notch the fuse box on my personal vehicle as well, wish I didn't have to but it helps so much when you do that!👍 Thanks for linking your video!😃
Could you provide a link to the turn signal bulb? I am having trouble finding it on the site. Thanks!
You would need a pair of the Armor series 7443 bulbs, and a pair of resistors! I have linked both of them for you, and if you have any other questions, let me know!
LED Bulbs: headlightrevolution.com/gtr-lighting-armor-series-7440-7443-led-bulbs/
Turn Signal Resistors: headlightrevolution.com/gtr-lighting-50-watt-6-ohm-gold-style-resistors-for-custom-installation/
@@HeadlightRevolution What about the Carbide series used in the video? He never mentioned if he used the CK or non CK style.
+HeadlightRevolution Are the DRL's the same brightness on the Hybrid model as they are on the XB series?
Yes they are! I’m glad Morimoto kept them bright on these models too, They are my favorite part.
@@HeadlightRevolution This video just sold me those then. Cant wait to get them. hopefully the preorder wait isn't too long.
Do you know if they have any plans to make the Hybrid version for the 4Runners?! Cause I’d definitely rather go that route.
I am not sure if that is in the works, haven't heard of that happening as of right now. We will of course keep you posted if we get anything new like that!