Explaining the process just helped me a lot. One thing that might also be important is to wait a couple of minutes until the oscillators are warmed up. Thanks a lot!!!
I don't see why the trimmer has to be at the back of the module and I don't see why should you need a trimmer either. It doesn't make any sense to me. Like, when tuning a guitar, the pegs are easily accessible. In an ideal world to me, you should be able to tune them with just a knob at the front of the panel, without having to disassemble anything and without the need of tools like a screwdriver. Yes, I know this is not going to be a popular opinion.
is there any sort of confirmation the calibration is writing? I have tried following the video, but my outputs remain consistently off... the same measurements as before calibration
Thanks for the video helped a little bit. I got a Behringer 921B Oscillator which i messed up completely due to missing knowledge :-). This OSC has 3 trimers (VR1 FREQ ADJ, VR2 HI ADJ and VR3 SCALE). My main issue is, that at one point I can not trim further down (trimmer clicks, stops in the khz range). Is there any advice you can give to set the trimmers to an initial state like turn trimmer xyz completely left, right or to middle etc. before starting the calibration that I'm able to dial in the lower frequencies? Many thanks.
Hi. From our experience of you were running out of useful scale squeezing turns, usually going up or down one-two octaves helps to get into a useful range and try to tune again
Hi friend, thank you very much for this video! Just a little question: i need to calibrate my Doepfer Dark Energy III, and i ask to you (if you know) if the procedure is the same? Know you what is the trimmer to calibrate the oscillator? I try anyway to calibrate it! Thanks a lot!🙏🏻☮️
Explaining the process just helped me a lot. One thing that might also be important is to wait a couple of minutes until the oscillators are warmed up. Thanks a lot!!!
Wow. This was very helpful. And I was able to successfully calibrate my furthrrr generator. Thank you very much for this!
Now I am ready to tune my oscillators, thank you for making this video! :)
Yesss i know need to tune my Furtherrr thanks for this one
now i know how...looking good in silver to...🖤
Fantastic Video! Just what you need! Thank you!
Nice new front panels for that Furthrrrr!
I don't see why the trimmer has to be at the back of the module and I don't see why should you need a trimmer either. It doesn't make any sense to me. Like, when tuning a guitar, the pegs are easily accessible.
In an ideal world to me, you should be able to tune them with just a knob at the front of the panel, without having to disassemble anything and without the need of tools like a screwdriver.
Yes, I know this is not going to be a popular opinion.
Wir freuen uns, Ramses Electronic Imaging and Sound Systems unter uns zu sehen.
i got to do this with my grandmother moog lmao
is there any sort of confirmation the calibration is writing? I have tried following the video, but my outputs remain consistently off... the same measurements as before calibration
Thanks for the video helped a little bit. I got a Behringer 921B Oscillator which i messed up completely due to missing knowledge :-). This OSC has 3 trimers (VR1 FREQ ADJ, VR2 HI ADJ
and VR3 SCALE). My main issue is, that at one point I can not trim further down (trimmer clicks, stops in the khz range). Is there any advice you can give to set the trimmers to an initial state like turn trimmer xyz completely left, right or to middle etc. before starting the calibration that I'm able to dial in the lower frequencies? Many thanks.
Hi. From our experience of you were running out of useful scale squeezing turns, usually going up or down one-two octaves helps to get into a useful range and try to tune again
@@Endorphines I give it a try, thx
Where did you get the Supremesque Eurorack shirt?
Where did all the mushrooms go? No more cows? 😲
Hi friend, thank you very much for this video! Just a little question: i need to calibrate my Doepfer Dark Energy III, and i ask to you (if you know) if the procedure is the same? Know you what is the trimmer to calibrate the oscillator? I try anyway to calibrate it! Thanks a lot!🙏🏻☮️
Yes bro, the procedure is same for all the oscillators just the direction of the trimmer may be opposite
@@Endorphines Many thanks friend! I’ll let you know!🤞🤞