Greetings, very good video. Could you help me, I followed all the steps in the video but once the fuser was assembled, the film does not rotate. What could it be?
If you were rebuilding VersaLink B400/B405 series fuser and used the silicone oil from the oil application pad package, then try to re-apply the oil with the oil taken from the fixing film package (it looks yellowish). In some cases the yellowish oil from the fixing film package works better in VersaLink B400/B405 series fuser units. In Phaser 3610 / WorkCentre 3615 series both types of oil should work OK. Anyway, please double check the following: - proper attachment of the oil application pad cloth - proper assembling of the fixing film assembly - proper attachment of the springs that apply pressure between the upper roller and the fixing film - the surface of the fixing film and upper roller are cleaned from any oil with isopropyl alcohol All the above may cause the problem Good luck!
@@CETGroupUSAInc Regards, I cleaned everything and reapplied the oil. the fuser works fine 3 days and then it starts to wrinkle the paper. What fat do you recommend?
@@FranciscoRodriguez-vu9kf We recommend the following: 1. Check if there is any pieces of paper or other trash left in the paper path before the fuser unit, in the fuser unit and after the fuser unit. 2. It's possible the red silicone insert under the oil application pad cloth had some damage when you were rebuilding the fuser unit. If it was damaged, you may not resolve this issue as there is no replacement silicone insert available now. 3. Thoroughly clean the fuser unit metal entrance guide with acetone to remove any toner contamination. Check if the surface of the guide is smooth. 4. Thoroughly clean the fuser unit plastic exit guides with acetone to remove any toner contamination. Check if the ribs on both guides are smooth. 5. Clean the upper roller picker fingers with acetone to remove any toner contamination. Check if the picker fingers are not damaged and properly seated. 6. Clean the exit rollers and exit section guides, that are located in the machine (not in the fuser unit) with isopropyl alcohol. Good luck!
Greetings, very good video. Could you help me, I followed all the steps in the video but once the fuser was assembled, the film does not rotate. What could it be?
If you were rebuilding VersaLink B400/B405 series fuser and used the silicone oil from the oil application pad package, then try to re-apply the oil with the oil taken from the fixing film package (it looks yellowish). In some cases the yellowish oil from the fixing film package works better in VersaLink B400/B405 series fuser units. In Phaser 3610 / WorkCentre 3615 series both types of oil should work OK.
Anyway, please double check the following:
- proper attachment of the oil application pad cloth
- proper assembling of the fixing film assembly
- proper attachment of the springs that apply pressure between the upper roller and the fixing film
- the surface of the fixing film and upper roller are cleaned from any oil with isopropyl alcohol
All the above may cause the problem
Good luck!
@@CETGroupUSAInc Regards, I cleaned everything and reapplied the oil. the fuser works fine 3 days and then it starts to wrinkle the paper. What fat do you recommend?
@@FranciscoRodriguez-vu9kf
We recommend the following:
1. Check if there is any pieces of paper or other trash left in the paper path before the fuser unit, in the fuser unit and after the fuser unit.
2. It's possible the red silicone insert under the oil application pad cloth had some damage when you were rebuilding the fuser unit. If it was damaged, you may not resolve this issue as there is no replacement silicone insert available now.
3. Thoroughly clean the fuser unit metal entrance guide with acetone to remove any toner contamination. Check if the surface of the guide is smooth.
4. Thoroughly clean the fuser unit plastic exit guides with acetone to remove any toner contamination. Check if the ribs on both guides are smooth.
5. Clean the upper roller picker fingers with acetone to remove any toner contamination. Check if the picker fingers are not damaged and properly seated.
6. Clean the exit rollers and exit section guides, that are located in the machine (not in the fuser unit) with isopropyl alcohol.
Good luck!
How compatible is this stove with the B405? Has anyone tried it?
The fuser unit being rebuilt works in the
Xerox Phaser 3610N/3610DN, WorkCentre 3615DN, and VersaLink B400/B405. Hope that helps!
You should change name of video to “why buy a new fuser”