I use 1/16th clear setting blocks under my glass to ensure it never sags. I also silicone my holes before screwing down clamps then over the top of the screw and finally I go around the clamps with crystal clear silicone as I do the perimeter. I had a clamp that allowed water to flow to the outside of the shower. Few more tips. I always line the entire curb with 1/16th shims and I tape some to the wall especially to protect the corners of the glass. Once I have positioned it I remove all shims except bottom near each corner
Great Vid buddy. Here's a hint for installing the brackets. When you drill through tile, start it with the bit you got, BUT change to the CIRCULAR DIAMOND BIT and finish with that. ALSO, I kinda like your idea of cutting the screws shorter, BUT don't worry about penetrating the rubber barrier with a longer screw>> As for cutting it shorter, there is no way to guaranty you won't cut through the barrier so ,Just pre-install the screw to get a nice hole going into the wood, and then inject with pressure a clear silicone that will seal the wood. Re-install the screw a few times with added silicone to make sure its well coated and Add additional silicone to the screw when you re-install it the final time and the hole will be well filled with silicone and won't leak.
@@ramsareit you could make a simple template using a strip of cardboard, painters tape or anything that's straight to mark the holes on the glass. Then attach to the shower wall and transfer the marks. No measuring necessary.
I have been binge watching your channel for hours now. Very impressed with your level of detail, the way you explain things and your overall attitude. I am baffled why you don't have 500K subscribers. I am getting ready to tackle my shower, and I can now see all the things the previous person did incorrectly. Thank you.
Hey Coach! I think I watched about 50 of your videos . ITS GOOD TO see skilled trades people.e at work! A question about the curb, is it possible to slope the top inwards toward the pan 1/4" per foot, or move the glass to the inside instead of the outside edge? To eliminate standing water?
I bought the Bosch suction jig and water pump system for drilling tile. works amazing. I always throw some silicone in the holes before putting the screws in.
Use rubber setting block and you can cut them out after glass is set and clamps tightened. Plastic shims are much more difficult to get out. But, it does look good. That is one of the easiest glass installs to do.
When you measured I watched the shim bend up. That's why your measurement was off. I'd have measured and then added in the thickness of the shim, it would be perfect. You really should show how to silicone the gap on the wall and floor, it's not something people can just do. Taping the edge of the glass is easy, but taping the wall on each side so sillcone doesn't exceed the thickness of the shower glass is worth explaining. The one glass wall I've done so far it's very difficult to see the clear silicone - I'm very detail oriented like you so worked hard to ensure a perfect application, it's important.
@@curtiscrane2749 Always create an angle into the shower to drain the curb top. It doesn't need much but is important to avoid water dripping outside the shower, and standing water which will result in ugly stains where there is hard water. 2 degrees is enough, and not noticeable by the human.
Awesome Dave! They are seriously the best workpants out there. Did you use the TILECOACH15 code at checkout to get the 15% off? truewerk.com?sca_ref=539863.kgOEqdxQ87
@@TileCoach I had to go back and look right now to see where the link was. I didn't click on it. I just saw the tagline that said something like "checkout these pants @truewerks. I got 15% off but I jump at the opportunity to give back to you for all you do so I bummed I didn't see your link. If they're half as good as the reviews I'll order more. I just wanted to find my size first.
The only thing I would tell you different is when your bringing the panel in, you need rubber pads everywhere along the bottom. Now your doing a 1/2 glass which is very hard to break but you can still chip a chunk off the corner . And if you have the 1/16 rubber under each corner then its easy to lift aside to add more rubber blocks so that you get the desired height. I typically do 3/8 shower panel just to save my back, but if the customer absolutely wants it then I do it but they get charged ALOT. I also usually sell the customer a panel that has a special coating on it on the inside.Also you can drill straight down , silicone the hole and plus you should be siliconing the inside bracket . Its super nice that you do the tile too, that way you got it nice and square, I just do the glass shower installations, we had one yesterday 1 1/8 out of square, thats the kind of drywallers that are out there...just don't give a crap. Anyway overall looks like ya did a great job
Another perfect install! Thank you so much for showing this. Based off your advice and videos, I created a curbless shower in my master bath that I absolutely LOVE. I am trying to convince my boss to install a screen like this instead of a cheesy sliding door with metal frames and made in China crap. Keeping fingers crossed. Thanks again for the great video!
Put the panel up on 1/8 clear shims, center it and level it and have someone on the inside holding it leveling it at the same time as well as the uc-79 and drill the holes at an angle, screw them in and seal it with clear silicone. Saves a lot of time.
We set the glass on the curb on setting blocks and the mark our holes and the drill the holes. Elimination of measurements and assured of center of notches. Sometimes we are even able to drill the holes with the glass in place.
Beautiful bathroom! Thanks for all you do on this channel. I’ve learned a lot. Get home from a long day of bathroom remodeling..... watch someone else remodel a bathroom. 👍
Going with floor to ceiling hotel shower curtains because I have the room. There’s more privacy in than glass and they should keep in the warmth and moisture .
Great video guys thanks. Hey I’m thinking furring ceiling on down to be flush with doors in case deciding to be able utilize shower as a make shift steam sauna Thoughts?
Another cool video. I’m considering using a clear glass fixed panel @ 32-36”Wx78”H onto right side of curb of a Dreamline 30x60 shower pan. Glass probably to have have 3 quadrants with black matte trim. Directly in front is toilet on right side then the vanity. Flooring most likely to be LVT on wood subfloor. Could utilize waterproof product similar to Red Guard or alternative option to attain max water proofing if opting to leave rear portion of pan left open without using typical glass door. What do you advise with flooring to be most conscious about ? 🙏
Spade bits are terrible for making holes in tile. They’ll only last you like two holes on hard porcelain. I’ve found that Milwaukee’s diamond max bits are good. They usually last be around two houses and two houses is roughly 8 showers total. Each shower is approximately 18 holes for three grab bars each. They’re the most cost effective bits I’ve found thus far and I’m no Milwaukee fan
LOVE that style of shower. I like doorless and open showers personally. Don’t think ppl realize just how HEAVY glass that size is, not to mention installing it can be nerve racking; as it takes just one wrong move.....to have a BAD day🤦🏼♂️😉 WELL DONE Guys👍🏻 Out of curiosity....?? 9:08 You concerned about going through water proofing on the vertical walls when installing the hardware for glass? Know the highest one is above spray/wet zone, so wouldn’t necessarily matter if did; but what about the lower one? Thx for another beautiful shower, and gonna be redoing my little bathroom soon; think might go this style; as really does look gorgeous. I do wanna hopefully mount my toilet into the wall instead of having it bolted to floor; so will see if it’s “doable” when demo back to studs. L8R ✌🏻
Hey bro great info and video!! I would like to ask you why you don't use the pre fab shower pans? Like Laticrete shower pans and curbs? I'm getting ready to do my shower with laticrete pre fab shower pan I remove my bath tub now installing shower.. Would you have any tips or suggestions? Thank you bro!!
Nice video. Question our glass around the shower only have too brackets to hold the glass lot the bottom that sits on top of marble slab. I guess the builder messed up or not sure what the case was. But they just got caulking around the bottom and the side. Very insecure. What’s the best solution without having to change the entire glass
I'll take full length screws with silicone in the holes into the waterproofing over shortened screws.. between silicone on the hole , screw threads , screw heads, the minimal water that hits and stays, not a big concern.. that heavy glass I want supported
ALWAYS have a stud behind the door hinge locations, on both sides of the door actually, sliding doors are less reliant on the studs because they're not supporting the weight but hinged doors 100% need a stud behind the tile
Questions to make sure my walking shower walls are built correct: Am I using the right steps in the shower walls and is the drywall ok : 1. Install drywalls on framing 2. Cover the drywalls with waterproof Aqua paper. Is this correct ? 3. Install lath on top of the drywalls and waterproof paper 4. Float the walls with cement , how thick it should be and what kind ? 5. Thin set and tiles . What kind of thin set for big tiles What am I missing ? Am I correct ? Is the drywall correct to have waterproof paper, lath , and concrete on top of it ? Can you correct me and advise me ? What are the correct steps and materials step by step?
Set the diverter to the water comes out the handheld sprayer, then direct the spray against the wall. Easy, I do it every day in my shower. If you remember to set things that way on exit you just walk in and turn it on.
Good morning I’m currently remodeling my bathroom and I have a bathtub shower and I installed Durarock and I waterproof the tiles in the shower are 12 by 24 porcelain what type of thin set do you recommend to install the tile I live in north New Jersey so we see all 4 seasons and summer gets super humid and winter gets super cold I have been watching you since September learning and finally at the end of December I took the dive into gutting the entire bathroom bringing it down to studs on the walls and adding exhaust fan it’s a lot of work but watching your videos helped me pull through it thank you for all you do you are amazing so can you help me find a thunder to apply the tile and a good grout there are way to many options out there and now I’m just confused please help me pick the correct products for the region I live in please 😊🔥😊🔥
@@TileCoach how tall was it,we paid 600 or so, but only 72x34, inch high,and 3/8 thick w design in glass,screen,linea surf,dreamline,amazon delivered to garage,depot sells also,just wanted a comparrison,...do you happen to know if tempered glass can be drilled, or no?
@@TileCoach 1/2" Holy crap... no wonder it's heavy! Really wish you lived near me, I have a bunch of bathrooms to remodel. Started doing one myself (also want door-less), but if I knew I could hire someone as meticulous as you, I'd pay to have it done right. I've had better luck with DIY than contractors, unfortunately. Wanna fly out to Florida to do an episode? :)
Also---very important to remember---you SHOULD be using a CLEAR PLASTIC SHIM (different thicknesses) and once fit properly MUST be LEFT INSTALLED with silicone sealant covering the shim to help hold it in place. This will ensure the glass WON'T slip or change positions. IF the glass come in contact with the tile, it can shatter. Sorry about that.
yes indeed. I just put in a glass warehouse screen today. came with the clear rubbery-plastic shims for the heel support, then I siliconed the tile to the glass edge. My shower pan is not quite level so this was very necessary to keep it an even 1/8" from to the plumb wall.
Hi there. Great video. Do you know if I can use brackets that do not require notching or holes in the glass? Also, for the screws, do you need any type of plugs or does the screw goes directly in the hole you made in the tile? Thank you!
I'm wondering about that too. I've been in a number of hotels that have half walls like this, and there is always a lot of water all over outside the shower that needs to be mopped up. Also wondering how much flex there is in the corner of the the glass panel that isn't attached to anything. Would it take a 250lb guy slipping in the shower and falling into it? I have some doubts
Question that may be silly- but I’ve seen a lot of the one glass kinda style for modern showers and I’m always baffled and confused on how ppl would avoid not getting water everywhere since there’s just that big open gap. Is this just for aesthetic purposes or it’s actually practical? Haha 😅
I installed a vigo enclosure and had leaking around the clamps. I'm going to be installing an inline door for my master bath, I'm going to fill the clamp with CRL and a touch underneath to beat the leaks.
Going the same route with zero door. I'm currently shopping for frame-less glass shower screen, and all I'm finding are vendors selling with a frame. I like to find what coach is installing with just the clips.
Can anybody advice me how much length of shower I need cover with the glass panel before I can have the opening so there not much splash out from the shower area?
looking for advice.... we had a contractor remove our shower insert and tile the shower entirely.... from what I saw during the install, he covered the walls and floor as well as a creating built in shelf all with Durock. Then used Uncoupling Membrane Mortar (not the actual membrane just the mortar) to adhere the tiles to the Durock... He didn't cover the surface with the mortar, just back-buttered the tiles and stuck them to the Durock. then of course finished off with grout.... *no redguard, no pan liner, nothing (curbless shower) should I trust this or have it re-done? we have not used the shower yet but it is in our master and will eventually use it often.
Yep, water doesn't sit on the vertical surface and it's there long enough to get past any silicone - do seal the bracket just for that little more insurance.
If you would like to show your support please consider purchasing an T-Shirt from our webstore at www.tilecoach.com/shop. Love you guys!
I still jam some silicone in the holes before I screw the brackets down. Just an extra step that prevent any water penetration.
Me too . Always.
I use 1/16th clear setting blocks under my glass to ensure it never sags. I also silicone my holes before screwing down clamps then over the top of the screw and finally I go around the clamps with crystal clear silicone as I do the perimeter. I had a clamp that allowed water to flow to the outside of the shower. Few more tips. I always line the entire curb with 1/16th shims and I tape some to the wall especially to protect the corners of the glass. Once I have positioned it I remove all shims except bottom near each corner
That’s a professional tip and something I’ve been looking for. These are the tips that should be highlighted!
Absolutely !!!
I love that door-less design.
Great Vid buddy. Here's a hint for installing the brackets. When you drill through tile, start it with the bit you got, BUT change to the CIRCULAR DIAMOND BIT and finish with that. ALSO, I kinda like your idea of cutting the screws shorter, BUT don't worry about penetrating the rubber barrier with a longer screw>> As for cutting it shorter, there is no way to guaranty you won't cut through the barrier so ,Just pre-install the screw to get a nice hole going into the wood, and then inject with pressure a clear silicone that will seal the wood. Re-install the screw a few times with added silicone to make sure its well coated and Add additional silicone to the screw when you re-install it the final time and the hole will be well filled with silicone and won't leak.
Before you drill, put that glass up where you want, then mark the holes. That way it’s always perfect.
I th ought the same, but that glass is HEAVy...EVEN WITH THE SUCTIONS CUPS
@@ramsareit you could make a simple template using a strip of cardboard, painters tape or anything that's straight to mark the holes on the glass. Then attach to the shower wall and transfer the marks. No measuring necessary.
that’s what’s i do clamps works perfect every time
I have been binge watching your channel for hours now. Very impressed with your level of detail, the way you explain things and your overall attitude. I am baffled why you don't have 500K subscribers. I am getting ready to tackle my shower, and I can now see all the things the previous person did incorrectly. Thank you.
Welcome aboard!
Hey Coach! I think I watched about 50 of your videos . ITS GOOD TO see skilled trades people.e at work! A question about the curb, is it possible to slope the top inwards toward the pan 1/4" per foot, or move the glass to the inside instead of the outside edge? To eliminate standing water?
Just got a job doing shower inclosers really liked your post thanks.
Awesome job, same exact set up in my kids bathroom tiles/glass getting ready to set the glass and watching a few videos before I go for it.
Thank you for your video, it's very good, I had to install a glass door in a shawer and I had doubts, but your video served me a lot. God bless you.
I like the shower screen looks clean, great install coach and crew.!
I bought the Bosch suction jig and water pump system for drilling tile. works amazing. I always throw some silicone in the holes before putting the screws in.
I'm building one now. I lost count on showers/tub surrounds with frameless doors but this will only be my 5th doorless.
Very clean work Isaac
Use rubber setting block and you can cut them out after glass is set and clamps tightened. Plastic shims are much more difficult to get out. But, it does look good. That is one of the easiest glass installs to do.
I really like the simplicity of no door no hinges.
When you measured I watched the shim bend up. That's why your measurement was off. I'd have measured and then added in the thickness of the shim, it would be perfect. You really should show how to silicone the gap on the wall and floor, it's not something people can just do. Taping the edge of the glass is easy, but taping the wall on each side so sillcone doesn't exceed the thickness of the shower glass is worth explaining. The one glass wall I've done so far it's very difficult to see the clear silicone - I'm very detail oriented like you so worked hard to ensure a perfect application, it's important.
Do you build the top of the shower curb at a slight angle into the shower or just leave it flat?
@@curtiscrane2749 Always create an angle into the shower to drain the curb top. It doesn't need much but is important to avoid water dripping outside the shower, and standing water which will result in ugly stains where there is hard water. 2 degrees is enough, and not noticeable by the human.
When the music came on while he was drilling i thought his step mom was gonna walk in the bathroom
LOLOLOOL
😂😂
What are you doing step bro.
You can twist the bit whilst in the chuck by hand also. Listen for a small 'scrunch' it also provides a starter thread shaped to the bit.
Good job 👍 I’m doing one tomorrow. First stationary panels
Great looking shower
Just ordered the t2 truewerks pants. They look awesome!
Awesome Dave! They are seriously the best workpants out there. Did you use the TILECOACH15 code at checkout to get the 15% off? truewerk.com?sca_ref=539863.kgOEqdxQ87
@@TileCoach I had to go back and look right now to see where the link was. I didn't click on it. I just saw the tagline that said something like "checkout these pants @truewerks. I got 15% off but I jump at the opportunity to give back to you for all you do so I bummed I didn't see your link. If they're half as good as the reviews I'll order more. I just wanted to find my size first.
I hope he used the code. He would save 15% off
The only thing I would tell you different is when your bringing the panel in, you need rubber pads everywhere along the bottom. Now your doing a 1/2 glass which is very hard to break but you can still chip a chunk off the corner . And if you have the 1/16 rubber under each corner then its easy to lift aside to add more rubber blocks so that you get the desired height. I typically do 3/8 shower panel just to save my back, but if the customer absolutely wants it then I do it but they get charged ALOT. I also usually sell the customer a panel that has a special coating on it on the inside.Also you can drill straight down , silicone the hole and plus you should be siliconing the inside bracket . Its super nice that you do the tile too, that way you got it nice and square, I just do the glass shower installations, we had one yesterday 1 1/8 out of square, thats the kind of drywallers that are out there...just don't give a crap. Anyway overall looks like ya did a great job
Looks really nice great job yet again!
We pump silicone in the drilled out hole prior to the plug going in the curb for extra protection.
Nice job.
Great video! Everything you need to know for a quality installation, thanks!👌
So do you need to silicone along the inside joins?
Another perfect install! Thank you so much for showing this. Based off your advice and videos, I created a curbless shower in my master bath that I absolutely LOVE. I am trying to convince my boss to install a screen like this instead of a cheesy sliding door with metal frames and made in China crap. Keeping fingers crossed. Thanks again for the great video!
You can ask for wider cutouts for the clips and they'll normally do it, gives you a little more room to adjust
Glass vibes !!!!
Nice video tutorial, thank you very much
Put the panel up on 1/8 clear shims, center it and level it and have someone on the inside holding it leveling it at the same time as well as the uc-79 and drill the holes at an angle, screw them in and seal it with clear silicone. Saves a lot of time.
Why drill the holes at an angle?
We set the glass on the curb on setting blocks and the mark our holes and the drill the holes. Elimination of measurements and assured of center of notches. Sometimes we are even able to drill the holes with the glass in place.
Beautiful bathroom! Thanks for all you do on this channel. I’ve learned a lot. Get home from a long day of bathroom remodeling..... watch someone else remodel a bathroom. 👍
Going with floor to ceiling hotel shower curtains because I have the room. There’s more privacy in than glass and they should keep in the warmth and moisture .
Nothing better then a "nice tight screw"
Aman
I have seen other videos where the bottom hardware is just secured with double sided tape and silicone. Why risk the hole?
Great video guys thanks. Hey I’m thinking furring ceiling on down to be flush with doors in case deciding to be able utilize shower as a make shift steam sauna Thoughts?
Where the glass butts up against the tiles/wall do you also then put in some silicone sealant?
My question as well
Another cool video. I’m considering using a clear glass fixed panel @ 32-36”Wx78”H onto right side of curb of a Dreamline 30x60 shower pan. Glass probably to have have 3 quadrants with black matte trim. Directly in front is toilet on right side then the vanity. Flooring most likely to be LVT on wood subfloor. Could utilize waterproof product similar to Red Guard or alternative option to attain max water proofing if opting to leave rear portion of pan left open without using typical glass door. What do you advise with flooring to be most conscious about ? 🙏
Spade bits are terrible for making holes in tile. They’ll only last you like two holes on hard porcelain. I’ve found that Milwaukee’s diamond max bits are good. They usually last be around two houses and two houses is roughly 8 showers total. Each shower is approximately 18 holes for three grab bars each. They’re the most cost effective bits I’ve found thus far and I’m no Milwaukee fan
100% agree
Better than Lenox or montolit?
@@alexanderjamieson7971 yes, and they’re way cheaper. I’ve just about tried them all and the Milwaukee are the most cost effective
do you silicone around the door?
LOVE that style of shower. I like doorless and open showers personally.
Don’t think ppl realize just how HEAVY glass that size is, not to mention installing it can be nerve racking; as it takes just one wrong move.....to have a BAD day🤦🏼♂️😉 WELL DONE Guys👍🏻
Out of curiosity....??
9:08 You concerned about going through water proofing on the vertical walls when installing the hardware for glass? Know the highest one is above spray/wet zone, so wouldn’t necessarily matter if did; but what about the lower one?
Thx for another beautiful shower, and gonna be redoing my little bathroom soon; think might go this style; as really does look gorgeous. I do wanna hopefully mount my toilet into the wall instead of having it bolted to floor; so will see if it’s “doable” when demo back to studs.
L8R ✌🏻
Use the Bosch drill bits for tile. That are way better than those cheapies.
Hey bro great info and video!! I would like to ask you why you don't use the pre fab shower pans? Like Laticrete shower pans and curbs? I'm getting ready to do my shower with laticrete pre fab shower pan I remove my bath tub now installing shower.. Would you have any tips or suggestions? Thank you bro!!
Dude I like the idea with your Matt’s to protect the floor great idea. I’m gonna steak that one for sure.
Nice video. Question our glass around the shower only have too brackets to hold the glass lot the bottom that sits on top of marble slab. I guess the builder messed up or not sure what the case was. But they just got caulking around the bottom and the side. Very insecure. What’s the best solution without having to change the entire glass
I'll take full length screws with silicone in the holes into the waterproofing over shortened screws.. between silicone on the hole , screw threads , screw heads, the minimal water that hits and stays, not a big concern.. that heavy glass I want supported
Great video, as always. What do you mean about 30" clearance from the centre of the toilet drain to the glass door -- is that code?
30" total for toilet, 15" from centerline of toilet.
Slick -- what are the dimensions of this shower?
We are having ours installed now. Same type of set up. There is a small wiggle to it. Can you put your weight against it? Is that a hazard?
you are drilling through the tile on the wall, are you relying on the tile to hold the glass door or is it standard to have a stud right there?
ALWAYS have a stud behind the door hinge locations, on both sides of the door actually, sliding doors are less reliant on the studs because they're not supporting the weight but hinged doors 100% need a stud behind the tile
What do you think of using schluter deco sg to hold up the glass?
Questions to make sure my walking shower walls are built correct:
Am I using the right steps in the shower walls and is the drywall ok :
1. Install drywalls on framing
2. Cover the drywalls with waterproof Aqua paper. Is this correct ?
3. Install lath on top of the drywalls and waterproof paper
4. Float the walls with cement , how thick it should be and what kind ?
5. Thin set and tiles . What kind of thin set for big tiles
What am I missing ? Am I correct ? Is the drywall correct to have waterproof paper, lath , and concrete on top of it ? Can you correct me and advise me ? What are the correct steps and materials step by step?
So you don’t slightly slant the threshold into the shower so the water doesn’t puddle there and outside the shower?
Drilling in , do I need to waterproof the hole? I don’t want anything un-waterproofed after all this and the mold I had last time.
I would like a panel on an acrylic base. Do you have any recommendations?
Great video, bud 👍🏻
How are you going to turn the water on without getting sprayed with cold water?
Raincoat.
Set the diverter to the water comes out the handheld sprayer, then direct the spray against the wall. Easy, I do it every day in my shower. If you remember to set things that way on exit you just walk in and turn it on.
Good morning I’m currently remodeling my bathroom and I have a bathtub shower and I installed Durarock and I waterproof the tiles in the shower are 12 by 24 porcelain what type of thin set do you recommend to install the tile I live in north New Jersey so we see all 4 seasons and summer gets super humid and winter gets super cold I have been watching you since September learning and finally at the end of December I took the dive into gutting the entire bathroom bringing it down to studs on the walls and adding exhaust fan it’s a lot of work but watching your videos helped me pull through it thank you for all you do you are amazing so can you help me find a thunder to apply the tile and a good grout there are way to many options out there and now I’m just confused please help me pick the correct products for the region I live in please 😊🔥😊🔥
contact me at www.tilecoach.com
I did not know those types of bits would drill through porcelain. I just put a shower bar up and bought a diamond drill bit. Learn something everyday.
Come to Tennessee and install mine.
Did you use inserts into the tile to hold the screw in place?
Another great vid. How wide is the opening after install?
what size glass ,and about how much was it cost wise, nice job
1/2" clear. I think we paid $600 with hardware. Delivered to jobsite.
@@TileCoach how tall was it,we paid 600 or so, but only 72x34, inch high,and 3/8 thick w design in glass,screen,linea surf,dreamline,amazon delivered to garage,depot sells also,just wanted a comparrison,...do you happen to know if tempered glass can be drilled, or no?
@@sonofthunder.Tempered glass can not be drilled. It would explode in thousand pieces due to the internal high stress caused by the tempering process
@@TileCoach 1/2" Holy crap... no wonder it's heavy! Really wish you lived near me, I have a bunch of bathrooms to remodel. Started doing one myself (also want door-less), but if I knew I could hire someone as meticulous as you, I'd pay to have it done right. I've had better luck with DIY than contractors, unfortunately. Wanna fly out to Florida to do an episode? :)
It's easy but heavy glass, I like fix glass in bathroom better .
I work aluminum and Glass
Nice work ✊🏻
What’s the dimension of the fixed glass shower wall installed in this video, please?
Nice I stall. The shower faucet handle should have been on the opposite wall tho
Also---very important to remember---you SHOULD be using a CLEAR PLASTIC SHIM (different thicknesses) and once fit properly MUST be LEFT INSTALLED with silicone sealant covering the shim to help hold it in place. This will ensure the glass WON'T slip or change positions. IF the glass come in contact with the tile, it can shatter. Sorry about that.
Thats great info. Im not a tiler and knew this couldn't be the right way to do it. He simply made a band-aide to fix his mismeasurement.
yes indeed. I just put in a glass warehouse screen today. came with the clear rubbery-plastic shims for the heel support, then I siliconed the tile to the glass edge. My shower pan is not quite level so this was very necessary to keep it an even 1/8" from to the plumb wall.
Can these glass shower panels be installed over foam type curbs?
Hi there. Great video. Do you know if I can use brackets that do not require notching or holes in the glass? Also, for the screws, do you need any type of plugs or does the screw goes directly in the hole you made in the tile? Thank you!
I am thinking about getting one but anoth clip says his clients always come back asking for a door. What do you think? 🤔
What size is that shower? 60x32?
When the corner of the glass door in the shower is cracked, is it dangerous?
What's an acceptable shower size to have a walk in shower without having water splash everywhere outside during a shower? Thank you
I'm wondering about that too. I've been in a number of hotels that have half walls like this, and there is always a lot of water all over outside the shower that needs to be mopped up. Also wondering how much flex there is in the corner of the the glass panel that isn't attached to anything. Would it take a 250lb guy slipping in the shower and falling into it? I have some doubts
Wow, installing this shower glass looks really hard stuff..
Question that may be silly- but I’ve seen a lot of the one glass kinda style for modern showers and I’m always baffled and confused on how ppl would avoid not getting water everywhere since there’s just that big open gap. Is this just for aesthetic purposes or it’s actually practical? Haha 😅
So, Isaac, did you then silicone the glass?
Yes
I installed a vigo enclosure and had leaking around the clamps. I'm going to be installing an inline door for my master bath, I'm going to fill the clamp with CRL and a touch underneath to beat the leaks.
Did you put any type or sealer on?
Does the water splash from the (not covered side) ?
What size tiles are those? They look like 12x24
Excellent
Going the same route with zero door. I'm currently shopping for frame-less glass shower screen, and all I'm finding are vendors selling with a frame. I like to find what coach is installing with just the clips.
Go to a local glass supplier.
Can anybody advice me how much length of shower I need cover with the glass panel before I can have the opening so there not much splash out from the shower area?
66%
What is the minimum width of shower glass for a no-door shower? I plan on have a 6 foot wide shower.
looking for advice.... we had a contractor remove our shower insert and tile the shower entirely.... from what I saw during the install, he covered the walls and floor as well as a creating built in shelf all with Durock. Then used Uncoupling Membrane Mortar (not the actual membrane just the mortar) to adhere the tiles to the Durock... He didn't cover the surface with the mortar, just back-buttered the tiles and stuck them to the Durock. then of course finished off with grout.... *no redguard, no pan liner, nothing (curbless shower)
should I trust this or have it re-done? we have not used the shower yet but it is in our master and will eventually use it often.
Ouch! You better seal grout à lot, I would think. Ilniar drain ?
I have the shower installed and would like to have the glass screen like you have. Do you know what is the width of the glass?
can you install this type of glass on the side of a bathtub?
Yes
Coming from someone who installs shower glass daily there is definitely simpler ways that are quicker and pretty much fool proof
Like?
can I ask for the size of the glass?
Awesome
fucking awesome. now for the GE silicone supreme clear. and kick ass baby for 50 years. woohoo.
That a 5’ shower….how wide is the opening to walk in about 2’ ?
So it's OK to go through the waterproofing in the walls but not the curb?
Put silicone in the screw holes and on to the threads of the screw.
Yep, water doesn't sit on the vertical surface and it's there long enough to get past any silicone - do seal the bracket just for that little more insurance.
1.21 30 inch clearance needed and has 15 inch ???
What's a bathroom remodel like that cost for just labor ?
i BOUGHT USED GLASS WITHOUT THE HARDWARE , WHERE CAN I BUY THESE METAL ATTACHMENT HARDWARE PIECES.
thanks
Any dealer in Delhi