Thank you so much for the video. I just fixed the belt alightment issue with this video. You gotta keep adjusting back and forth and try until it works. I didn't touch the right side though. Just kept playing with the left side, thinking it would be too confusing if I adjust both sides
Unfortunately the video is wrong. If belt moves to right side, use wrench from right side and turn as clockwise. If belt moves to left side, use wrench from left side and turn clockwise.
Ben anlamadım. Sol Taraf sağa çekerse tam tersi soltaraf çeyrek döndürmeli, sağ da sıkıntı varsa sağa çekme sola çeyrek çevirmeli ama bende ayarlar ok gibide olsa üstüne çıkınca duruyor
Well, the manual also states to not overtighten the screws.. So instead of tightening from the left side, you could also turn it counter-clockwise from the right side to loose it. So you should check whether its already too tight and act accordingly...
What do I do if the right screw doesn't do anything? I've tried following the instructions and it kept going to the right. I understand now that it's probably because the right screw isn't doing anything.
you are not following the instructions correctly : they say , if the belt is left you turn clockwise the left screw. If the belt is right turn clockwise the right screw.
Is it me or this doesn't make any sense yes my belt is going on the right side and I adjust it from the left (Anticlockwise) and then I wanted to tighten the belt and I did both (clockwise) and now the belt is running on the left side again 😭😭😭😭
Thanks for the guide! This was more helpful than the official manual…
Thank you so much for the video. I just fixed the belt alightment issue with this video. You gotta keep adjusting back and forth and try until it works. I didn't touch the right side though. Just kept playing with the left side, thinking it would be too confusing if I adjust both sides
it worked. the manual was actually incorrect!
push speed+ and modechange for 3 secs to enter calibration mode.
Makes it easier
THANKS - IT WORKS - MAKE SURE THE TREADMILL IS STOPPED WHEN YOU ADJUST VIA THE WRENCH
Unfortunately the video is wrong.
If belt moves to right side, use wrench from right side and turn as clockwise.
If belt moves to left side, use wrench from left side and turn clockwise.
Ben anlamadım. Sol Taraf sağa çekerse tam tersi soltaraf çeyrek döndürmeli, sağ da sıkıntı varsa sağa çekme sola çeyrek çevirmeli ama bende ayarlar ok gibide olsa üstüne çıkınca duruyor
Thanks so much!
what happens if you do counter clock wise :c
Well, the manual also states to not overtighten the screws.. So instead of tightening from the left side, you could also turn it counter-clockwise from the right side to loose it. So you should check whether its already too tight and act accordingly...
What do I do if the right screw doesn't do anything? I've tried following the instructions and it kept going to the right. I understand now that it's probably because the right screw isn't doing anything.
But how do I replace the treadmill belt? I cannot find any video about that, and the online manual does not explain. If you can explain, thank you
THANK YOU!!
I can not move the key inside the hole. It's too tide screwed up and I don't know what to do!
I was adjusting the belt and I turned it counter clockwise will it break my threadmil? thanks - just read the instructions :c
my belt is not aligned. it has a huge gap on the right side and i tried to turn the left side clockwise and it is still the same. What do i do?
I have the little bit similar issue
@Nikos Tsotsolas anyone has resolved the issue yet? whatever I do the belt keeps moving to the right! very frustrating!
I loosened both screws so I could move the tape. Then tighten both screws relatively firmly.
you are not following the instructions correctly : they say , if the belt is left you turn clockwise the left screw. If the belt is right turn clockwise the right screw.
My screw on the right side doesn't work. I haven't used the pad yet... I feel like I got ripped off
Is it me or this doesn't make any sense yes my belt is going on the right side and I adjust it from the left (Anticlockwise) and then I wanted to tighten the belt and I did both (clockwise) and now the belt is running on the left side again 😭😭😭😭
After calibration I step on on M mod it doesnot slip stopa but motor Works why
How I change the belt at xiaomi a1 walking pad?
Thanks!
Thanks!